Galvin Engineering GalvinSafe 190.80.10.12 Instruction sheet

Version 3.1, 13tth Aug. 2021, Page 1of 7
GalvinSafe®Free Standing Combi Shower, Axion®
MSR Eye/Face Wash, Hand Activated (HAWS)
PRODUCT CODE:
Galvin Engineering: 190.80.10.12
HAWS: 8330-A
PRE - INSTALLATION
LOCATION OF UNIT: The Model 190.80.10.12 (8330-A) Stainless Steel combination
Shower Eye/Face Wash should be installed in close proximity to potential accident
areas. It should be clearly identified, free from obstructions and easy to access.
SUPPLY LINE: The minimum recommended line size is 1-1/4” BSPT with 210 –600 kPa
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet supply is male 1-1/4” BSPT. Waste outlet is male 1-
1/4” BSPT.
INSTALLATION
Refer to installation drawing to clarify installation procedure.

Version 3.1, 13tth Aug. 2021, Page 2of 7
PARTS BREAKDOWN
ITEM
ITEM CODE
DESCRIPTION
1
190.92.00.10
SHOWER HEAD
2
190.92.04.30
VALVE ASSEMBLY
3
190.92.30.20
PULL ROD
4
190.92.12.10
EYE/FACE WASH HEAD
5
190.92.41.30
VALVE ASSEMBLY
6
-
STRIPE TAPE*
7
190.95.90.90
EMERGENCY EYE & SHOWER SAFETY SIGN
8
190.92.22.20
BOWL
9
190.91.22.12
FOOT TREADLE (OPTIONAL)
10
190.91.80.33
TEST TAG
11
-
L-STRAINER*
12
-
SS DUST COVER ASSEMBLY* (OPTIONAL)
* spare parts will require special order or may not be available (contact
Galvin engineering for more details).

Version 3.1, 13tth Aug. 2021, Page 3of 7
INSTALLATION PROCEDURE
Refer to Installation Drawing for clarification. Check parts list to ensure all required
parts are included. Use AS 4020 approved pipe joint sealant on all connections.
STEP 1: Prepare the emergency shower foundation by using the floor flange as a
template. Locate the three holes for the 3/8-16 UNC x 6” anchor bolts. (Not
supplied). They should extend 1” above the floor level.
STEP 2: Once the concrete foundation is ready (dry), assemble the floor flange to the
anchor bolts; then securely fasten with 3/8-16 UNC Hex nuts and 3/8”
washers (Not supplied). Seal and tighten floor flange and (1-1/4”) tee making
certain the waste tee is facing the proper location and the foot control holes
are facing side to side.
STEP 3: Assemble nipple (1-1/4” x 24”) to the tee and tighten with a pipe wrench.
STEP 4: Assemble the eye/face wash loop assembly to the (24”) nipple from Step
three. Connect the pipe wrench to the nipple between the two tees to avoid
damage.
STEP 5: Assemble in the following order:
Attach nipple (1-1/4” x 24”) onto the loop assembly.
Attach nipple (1-1/4” x 24”) onto the tee.
Attach tee (1-1/4” x 1-1/4” x 1”) onto nipple.
Attach nipple (1” x 8”) and valve assembly onto tee.
Attach street elbow (1”) and nipple (1” x 12-1/2”) onto valve.
STEP 6: Assemble showerhead onto street elbow (1”).
STEP 7: Assemble the sign onto theunit. Use the strap, screws, washersand nuts
provided to mount the sign onto the upright. The sign should be
positioned for maximum visibility.
STEP 8: Insert the plug into the optional supply line tee that is not used. Before
connecting the supply water line to the emergency shower; CHECK IF THE
ASSEMBLY IS RIGIDLY TIGHTENED AND FLUSH THE LINE
THOROUGHLY.

Version 3.1, 13tth Aug. 2021, Page 4of 7

Version 3.1, 13tth Aug. 2021, Page 5of 7
For more information about GalvinSafe®(Haws) products, see our website.
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1. No Flow.
1. Check the main shut-off valve.
2. Insufficient water flow.
2. Verify minimum 210 kPa flowing supply
line pressure.
3. Insufficient water flow on eye/face
wash, however, shower is sufficient
3. a. Verify minimum 210 kPa flowing supply
line pressure
b. Probable clogging of flow control due
to inadequate line flushing. Unscrew
eye/face wash head and remove the
four screws to disassemble head.
Clean flow control and reassemble
Head.
c. Remove plug located on L –Strainer
using a 9/16” wrench to access
clean filter screen.
4. Eye/face wash streams do not meet
desired eye level.
4. Possible blocked flow control, see above
solution. Possible non-leveled eye/face
wash assembly
5. Water does not drain properly.
5. Check your drain system for debris. Check
the main waste line of your building to see
if it does handle the capacity required for
the entire drainage system
6. Water leak between joints or fittings.
6. Tighten loose connections. If leak persists,
the application of hot water will sometimes
reseat improperly applied joint compound.
After 30 minutes wait and retest. A
persistent leak will necessitate reassembly
and additional sealant.
7. Insufficient water flow from shower,
however, eye/face wash is sufficient.
7. Probable clogging of flow control inside
showerhead. Unscrew showerhead off of
elbow and clean rubber flow control.

Version 3.1, 13tth Aug. 2021, Page 6of 7

``
Version 1, 12th April 2021, Page 7of 7
Version 3.1, 13tth Aug. 2021, Page 7of 7
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.