Galvin Engineering GalvinCare CP-BS Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 17 November 2022, Page 1 of 4
GalvinCare®CP-BS Lead Safe Mental Health Anti-Ligature Ceiling
Mounted Shower Rose Stainless Steel Plate
PRODUCT CODES:
- 121.70.10.00
SPECIFICATIONS
−The GalvinCare®Mental Health Ceiling Mounted Shower Rose provides anti-vandalism and anti-ligature
features.
−Used extensively in high risk, high security applications such as prisons, correctional facilities, and
detention centres.
−Constructed from heavy duty components and comes complete with special tamper resistant screws.
−For use with high pressure plumbing systems between 150 & 500kPa.
−Special consideration may be required when used with low water pressure systems and components.
−Chrome plate finish for easy cleaning and added durability
−Lead Safe™brass construction*
IMPORTANT: All GalvinCare®vandal resistant ceiling mounted shower roses are tested in accordance with
AS/NZS 3662 and leave our premises in good working order.
*As ‘lead free’ is not currently defined by law in Australia and New Zealand, we have based our definition of Lead Safe™ on the requirements of s1417 of the USA’s Safe Drinking Water Act (SDWA)
and the relevant US standards NSF61 / NSF372. The SDWA defines ‘lead free’ as “not more than a weighted average of 0.25% lead when used with respect to the wetted surface of pipes, pipe
fittings, plumbing fittings and fixtures”.
TECHNICAL DATA
Inlet
½” BSP - Male
Outlet
Shower Rose
Headwork
N/A
Working Pressure Range (kPa)
Min
150
Max
500
Working Temperature Range (°C)
Min
5
Max
70
Nominal Flow Rate (LPM)
6.6
Finish
Chrome
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.

© Galvin Engineering Pty Ltd
Version 1, 17 November 2022, Page 2of 4
Product Installation Guidelines
Version 1, 17 November 2022, Page 2 of 4
PRE-INSTALLATION - MOUNTING DETAILS –HOLE CENTRES
−If the mounting holes do not already exist, mark out and drill the holes as shown
in face plate hole dimensions. Ensure drill to suit suitable mounting methods.
−Recommended installation height above floor level is 2 metres (6’6”). Spread
pattern using mains pressure 500kP as shown in side image
Spread pattern
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Specialised products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
IMPORTANT: Whilst our product designs take into account a broad range of installation types and surfaces, it
is important that surfaces which fixtures are mounted to are flat and free from defect. Additionally, ensure any
protruding connecting thread is square to the wall so that the outlet sits flat against the wall when installed,
ensuring that there are no gaps between the wall and outlet. This is especially important when installing product
ranges that have been designed for correctional and health facilities, where special attention is required to
minimise ligature points and areas for concealment of contraband. In addition to ensuring the products are fitted
securely and in accordance with the following instructions, consideration shall be given to the use of non-pick
mastics such as BASF Sonolastic “Ultra” to ensure a high quality and safe installation.
FRONT MOUNTING
1. Secure shower assembly
−Fit the shower assembly into cealing cut out
spud hole.
−Secure shower assembly with suitable
fastenings as shown.
2. Connect the water line
−Connect water supply to the inlet.
−Use suitable sealant to prevent leaks.

© Galvin Engineering Pty Ltd
Version 1, 17 November 2022, Page 3of 4
Product Installation Guidelines
Version 1, 17 November 2022, Page 3 of 4
TESTING
−Turn on water supply, inspect the shower and check for any leaks.
Note: Never operate without a flow restrictor, as GalvinCare®Vandal Resistant Shower Rose will deliver full
mains pressure with unrestricted flow.

Version 1, 17 November 2022, Page 4of 4
Product Installation Guidelines
Version 1, 17 November 2022, Page 4 of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Wall shower is dripping water
Head-works are worn or
damaged
Remove and inspect the head-works,
remove debris and replace head parts if
damaged
Wall shower has inconsistent
flow
Blocked flow restrictor
Remove flow regulator from the body
and remove debris. Install an inline
strainer to stop further blockages.
Leak from behind body
Insufficient sealant
Apply more sealant
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.