Galvin Engineering CliniLever TCWSC150C Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.08
Version 1, 12 July 2022, Page 1of 5
CliniLever®CP-BS Hospital Wall Sink Set Taps
w/ 190 Gooseneck Outlet
PRODUCT CODES:
- TCWSC150C -TCWSC80C
- TCWSJ150C - TCWSJ80C
SPECIFICATIONS
−The CliniLever®product range is primarily used for hand washing applications in hospitals, aged care
facilities, schools and in-home care.
−CliniLever®products provide state of the art features to comply with the latest healthcare guidelines.
−Contra rotating handles to ensure ease of use
−Laminar flow aerator supplied as standard to reduce the spread of legionella.
−Smooth round design to facilitate easy cleaning and to help reduce dirt and bacterial growth.
−Quick action SBA’s includes brass jumper valve / ceramic disc component, with red and blue indicator
buttons on 80mm or 150mm lever action handles.
IMPORTANT: All CliniLever®healthcare taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
1/2” BSP –Female
Outlet
Laminar Flow Aerator
Headwork
Jumper Valve / Ceramic Disc
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
65
Nominal Flow Rate (LPM)
5.5
Finish
Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Spanner and hex key
−Thread tape

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.08
Version 1, 12 July 2022, Page 2of 5
PRE-INSTALLATION - MOUNTING DETAILS
In-wall valve body
−In-wall valve body must have G5/8”
female head to body thred
connection.
−Body should be mounted between 0
and 15mm behind the finished wall
surface.
Wall spud
- Wall spud must be ½” BSP male thred and
protrude from the finished wall by no more than
15mm
Note: In some situations, a male thread
connection on the spout may be more suited. If
so, please contact us on 1300 514 074
Note: Before installation, all lines must be flushed. We
recommend that a line strainer be installed prior to taps
to eliminate any foreign material.
TCWSC80C/TCWSJ80C
TCWSC150C/TCWSJ150C

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.08
Version 1, 12 July 2022, Page 3of 5
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Fit Tap Assembly and Connect
−Remove the spout from the wall elbow
using a hex key. This is to enable easy
installation and prevent the spout being
damaged
−Place the wall flange over the elbow. Fit
the elbow to the protruding wall spud.
We recommend using thread tape or an
equivalent to ensure the connection
does not leak.
−Ensure spout connection is pointing up
(vertical).
2. Refit the spout
−Refit the spout to the elbow. Tighten
the grub screw using a hex key.
Note: Do not overtighten grub screw.
Ensure spout swivels freely once installed.
3. Fit Spindle Assembly
−Remove handle and flange from cartridge
assembly. Unscrew the ¼ turn ceramic
head part from the threaded sleeve
assembly and screw ceramic cartridge
into the valve body by hand, tighten using
a 17mm spanner.
−Refit threaded sleeve and spindle.
−The ¼ turn ceramic head part MUST be
fitted into the wall body prior to refitting
the threaded sleeve and spindle. DO
NOT tighten cartridge by using the
spindle or the threaded sleeve.
4. Fit Wall Flange
−Ensure o-ring is fitted to the bottom of the wall
flange, and then hand-tighten the wall flange
onto the threaded sleeve.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.08
Version 1, 12 July 2022, Page 4of 5
5. Fit handle
−Ensure the spindle is in the closed position
and firmly press the CliniLever®lever
handle onto the spindle in the desired
orientation.
−Check operation of CliniLever®lever
handle. They should turn freely for a full ¼
turn.
−Secure the handle in position using the
supplied washer and stainless steel cap
screw.
6.Fit water temperature indicator & testing
−Once CliniLever®lever handle is secure; fit the
appropriate water temperature indicator.
−Once temperature indicator is fitted, check the
operation of the unit and inspect for any leaks.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping water
Jumper valves are worn or damaged
Replace jumper valve
Ceramic discs are worn or damaged
Remove and inspect SBA.
Remove debris and/or
replace SBA if damaged.
Tap seat is damaged
Refurbish tap seat using a
reseating tool.
Water is leaking from spindle
O-ring on jumper valve spindle is
damaged or worn
Replace o-ring
Water is not flowing from tap
Water is turned off
Turn water on
Aerator or flow regulator is blocked by
debris
Remove aerator and/or flow
regulator from tap and remove
debris. Install an inline strainer.
Obstruction on spout
Check if there are obstructions
hindering the water flow in the
spout and take it out.
Spindle is difficult to turn
(jumper valve)
Build up of scale on spindle, spindle
worn or o-ring has been damaged
Remove jumper valve, clean and
regrease. Replace o-ring.
Complete SBA may need to be
replaced.
Handle is loose
Screw has come loose
Tighten handle screw
Flange does not screw down
onto basin/sink surface
Tap bodies are set too far out
Re-position tap bodies and breach
piece

Version 2, 12 July 2022, Page 5of 5
Product Installation Guidelines
Document No.: 001.00.10.08
Version 1, 12 July 2022, Page 5of 5
SERVICE AND MAINTENANCE
JUMPER VALVE TAPWARE
CERAMIC DISC TAPWARE
1. Turn off the water supply and turn on the tap
handle to drain water from the bodies.
2. Remove the temperature indicator from the
handle.
3. Remove the handle from the tap.
4. Unscrew the top assembly from the body.
5. Check the o-ring on the spindle and the
jumper valve for wear and damage.
Replace if required.
6. Clean the spindle and body of debris.
7. Place a new o-ring (if required) onto the
spindle and re-grease with potable water
approved grease.
8. Re-assemble top assembly. Follow the product
installation guidelines for the relevant product
to re-assembly method.
1. Turn off the water supply and turn on the tap
handle to drain water from the bodies.
2. Remove the temperature indicator from the
handle.
3. Remove the handle from the tap.
4. Unscrew the ceramic head part from the
body.
5. Check the o-ring on the ceramic head part
for wear and damage. Replace if required.
6. Clean the head part and the body of any
debris.
7. Replace the cartridge and hand tighten back
into the body.
8. Follow the product installation guidelines for
the relevant product to re-assemble.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering
Pty Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or
implied. Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied,
including but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule
in the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance
or alteration of the product.