Galvin Engineering CliniLever TCBTC80CC User manual

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.00
Version 1, 23 November 2021, Page 1of 5
CliniLever®Basin/Sink Top Assembly
PRODUCT CODES:
- TCBTC80CC - TCBTJ80CC
- TCBTC80HC - TCBTJ80HC
- TCBTC150CC -TCBTJ150CC
- TCBTC150HC - TCBTJ150HC
SPECIFICATIONS
−The CliniLever®product range is primarily used for hand washing applications in hospitals, aged care
facilities, schools and in-home care.
−Our highly sought after lever design is easily operated with elbows or wrist to avoid hand contact.
−Quick action SBA’s includes brass jumper valve / ceramic cartridge component, with red or blue indicator
button on 80mm or 150mm lever action handles.
−CliniLever Top Assemblies are designed to screw directly into any 15mm body to Australian Standards
AS/NZS 3718.
IMPORTANT: All CliniLever®healthcare taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
5/8 BSP
Outlet
N/A
Headwork
Jumper Valve /
Ceramic Disc
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Jumper Valve / Ceramic Disc
Min
5
Jumper Valve / Ceramic Disc
Max
80
Construction
Brass
Finish
Chrome
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Spanner or adjustable crescent
80mm Handle - SERIES
150mm Handle - SERIES

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.00
Version 1, 23 November 2021, Page 2of 5
PRE-INSTALLATION - MOUNTING DETAILS
Note: Before installation, all lines must be flushed. We recommend that a line strainer be installed prior to top
assembly to eliminate any foreign material.
TCBTC80CC/TCBTC80HC/TCBTJ80CC/TCBTJ80HC
TCBTC150CC/TCBTC150HC/TCBTJ150CC/TCBTJ150HC
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions and
in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply
conditions must also comply to the applicable National and/or State standards. Failing to comply with these provisions
shall void the product warranty and may affect the performance of the product.
1. Disassemble & Fit
- Disassembly the top assembly per part
and fit the spindle to the basin body
- The top assembly is designed to screw
directly into any 15mm body that
complies with Australian Standard
AS/NZS 3718. Check that the existing
valve body complies to AS/NZS 3718.
2. Fit basin/sink flange
−Tighten the vanity flange onto the threaded basin
body.
−Take care not to overtighten
Spindle
Basin body
(Not Supplied)

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.00
Version 1, 23 November 2021, Page 3of 5
3. Locate handle
−Insert the adaptor bush onto the spindle
−When the spindle is in the closed
position, firmly press the lever handle
onto the spindle with levers facing
forward.
−Check the handle operation. It should
turn freely for a ¼ turn.
4. Fit handle
- Secure the handles in position using the supplied
screws and washers.
5. Fit water temprature indicator & testing
−Once the lever handles are secure, fit the
appropriate water temperature indicators.
−Hot/warm on the left handle, cold on the
right.
−Once secured, connect the hot and cold
water.
−Open the lever handles and ensure that
there is flow from both hot and cold
inlets.
−Inspect the tap and check for any leaks.
Spindle
Adaptor bush
Lever handle

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.10.00
Version 1, 23 November 2021, Page 4of 5
SERVICE AND MAINTENANCE
JUMPER VALVE TAPWARE
CERAMIC CARTRIDGE TAPWARE
1. Turn off the water supply and turn on the tap handle
to drain water from the bodies.
2. Remove the temperature indicator from the handle.
3. Remove the handle from the tap.
4. Unscrew the top assembly from the body.
5. Check the o-ring on the spindle and the jumper
valve for wear and damage. Replace if required.
6. Clean the spindle and body of debris.
7. Place a new o-ring (if required) onto the spindle and
re-grease with potable water approved grease.
8. Re-assemble top assembly. Follow the product
installation guidelines for the relevant product to
re-assembly method.
1. Turn off the water supply and turn on the tap handle to
drain water from the bodies.
2. Remove the temperature indicator from the
handle.
3. Remove the handle from the tap.
4. Unscrew the ceramic head part from the body.
5. Check the o-ring on the ceramic head part for
wear and damage. Replace if required.
6. Clean the head part and the body of any debris.
7. Replace the cartridge and screw tighten back into the
body.
8. Follow the product installation guidelines for the
relevant product to re-assemble.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping
water
Jumper valves are worn or damaged
Replace jumper valve
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove debris
and/or replace SBA if damaged.
Water is leaking from
spindle
O-ring on jumper valve spindle
is damaged or worn
Replace o-ring
Spindle is difficult to
turn (jumper valve)
Build up of scale on spindle, spindle
worn or o-ring has been damaged
Remove jumper valve, clean and regrease. Replace
o-ring. Complete SBA may need to be replaced.
Handle is loose
Screw has come loose
Tighten handle screw
Flange won’t screw
down onto basin/sink
surface
Tap bodies are set too far out
Re-position tap bodies and breach piece

Version 2, 23 November 2021, 5 of
5
Product Installation Guidelines
Document No.: 001.00.10.00
Version 1, 23 November 2021, Page 5of 5
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.