Galvin Engineering WaterMark 46638 Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document Number: 001.00.70.13
Version 1, 4 November 2022, Page 1of 4
BS Lever Action SBA
PRODUCT CODES:
- 46638 - 46714
- 46642 - 46722
- 46649 - 46726
- 46656 - 46730
- 46664 - 46748
- 46672 - 46755
- 46680 - 46763
SPECIFICATIONS
−The Galvin Engineering CliniLever®product range is primarily used for hand washing applications in
hospitals, aged care facilities, schools and in-home care.
−CliniLever®products provide state of the art features to comply with the latest healthcare guidelines.
−The main body is made of solid dezincification resistant (DR) brass rod, with a DR brass fixed outlet.
−Quick action SBA’s include ceramic cartridge components
IMPORTANT: All CliniLever®Healthcare taps are tested in accordance with AS/NZS 3718 and leave our
premises in good working order.
TECHNICAL DATA
Inlet
G 5/8”BSP –Male
Outlet
N/A
Headwork
Jumper Valve/ Ceramic Disc
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature (°C)
Min
5
Max
65
Nominal Flow Rate (LPM)
N/A
Finish
Brass
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without notice.
TOOLS REQUIRED
−Spanner and hex key
−Thread tape

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document Number: 001.00.70.13
Version 1, 4 November 2022, Page 2of 4
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and
in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply
conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
Note: Tapware body used as an example only. SBAs can fit on different kinds of Ezy-Wash bodies.
1. Remove Handle
−Prior to installation turn off the water supply.
−Remove the handle assembly. To prevent
damage, carefully pry off plastic indicator from
the handle. (Use a small flat bladed screwdriver
if necessary).
2. Replace spindle assembly
−Unscrew the head part from the threaded sleeve
using a 17mm spanner.
−Check seat inside tap body for pitting or damage.
Re-seat if necessary
3. Refit new head
-Refit new head into tap body.
Note: do not tighten cartridge using the
handle as this will result in damage to the
cartridge
4. Reassemble Handle
-Refit adaptor and reassemble handle by
reversing step 1.
-When installation is complete, slowly open
water supply and inspect for leaks.
New ceramic head
New head

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document Number: 001.00.70.13
Version 1, 4 November 2022, Page 3of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping water
Jumper valves are worn or damaged
Replace jumper valve
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Tap seat is damaged
Refurbish tap seat using a reseating
tool.
Water is leaking from spindle
O-ring on jumper valve spindle is
damaged or worn
Replace o-ring
Water is not flowing from tap
Water is turned off
Turn on water
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Spindle is difficult to turn
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Build up of scale on spindle, spindle
worn or o-ring has been damaged
Remove jumper valve, clean and
regrease. Replace o-ring. Complete
SBA may need to be replaced.
Handle is loose
Screw has come loose
Tighten handle screw

Product Installation Guidelines
Document Number: 001.00.70.13
Version 1, 4 November 2022, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not limited
to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s warranty
are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property
which is damaged if this product does not work properly, other costs resulting from labour charges, delays,
vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical,
electrical or any other circumstances over which Galvin Engineering has no control. This warranty shall be
invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of
the product.