GE 51209 User manual

Do not use in wet locations
Personal Security
Motion Sensor
with Keypad
User Manual

Motion Sensing Alarm
With Remote Control
Low Battery Indicator
The Motion Sensing Alarm has a low
battery indicator light. When the batteries
need to be replaced, the indicator will
flash slowly. Average battery life for
typical usage is up to one year.
Wall
Mount
Alarm/Chime Switch
Motion Sensing Alarm
Indicator Light

4
INSTALLING BATTERIES
The battery compartment is located on
the back of the unit.
Remove the battery compartment
screw and slide off cover in the
direction of the open arrow.
Insert (3) AA batteries (not included) .
Take care to note the polarity diagram
inside the battery compartment.
Replace the cover and secure screw.
Battery Compartment
Learn
Button
Learn
1.
2.
3.

5
CREATING YOUR PERSONAL ALARM CODE
The 4-digit keypad allows you to set a
personal code for arming and disarming
the alarm.
Remove the battery compartment
screw and slide off cover in the
direction of the open arrow.
Press the LEARN button once; the
red indicator light on the front of the
alarm will blink for 15 seconds. During
this time, input your 4-digit code. A
beep will confirm each input. The
unit will flash a green light 3 times
to confim your new 4-digit code has
been saved.
Replace the cover and secure screw.
INSTALLATION
The alarm is designed to be wall mounted
with the ball and socket mount (included).
The ball and socket mount will provide the
1.
2.
3.

6
flexibility to aim the motion sensor in a
particular direction.
Choose your desired location, such
as the corner of the room. This will
provide maximum coverage. NOTE:
The sensor has a 15-20 ft. detection
zone, with approximate angles of 110
degree horizontal x 70 degree vertical.
Recommended installation height is 6
to 8 feet.
110˚
20'
5'
20'15'10'5'
Feet
Feet
6'-8'
10'
15'
70˚
1.

7
Secure ball and socket mount to the
wall using either the provided wall
anchors or by screwing directly into a
wall stud. Once installed securely on
the wall, slide insert bracket of mount
into the back of the unit and lock
in place. The mount will click when
secured to the alarm.
OPERATING IN THE ALARM MODE
Locate the ALARM/CHIME switch on
the side of the alarm.
2.
1.

8
Slide switch to ALARM mode.
Arming the Alarm
Arm the alarm by pressing your 4-digit
code. A beep will sound after each
button is pressed.
When the 4-digit code is entered
correctly the unit’s indicator light
will flash green once. If entered
incorrectly, the unit will sound and
the indicator light will flash red three
times.
A red light will immediately begin to
flash indicating the 45-second exit
delay has started. The delay allows
time for you to leave the protected
area without triggering the alarm.
When motion is detected, the alarm
unit will sound a short tone and a red
light will flash. The alarm will activate
2.
1.
2.
3.
4.

9
in 30 seconds. The siren will sound
for 30 seconds (unless disarmed by
the remote) and then turn off. In 15
seconds the alarm will check for
motion. If motion is detected, the siren
will sound again. The cycle will repeat
until the unit is disarmed with the
remote.
Disarming the Alarm
When returning to the protected area,
simply enter your 4-digit code within
30 seconds to disarm the alarm.
When the fourth digit of your code is
entered, the unit will respond with two
tones and the indicator light will flash
green twice.
The unit will beep once if motion is sensed.
If the correct code is not entered within
30 seconds, the alarm will sound. Enter
correct code anytime after the alarm has
1.
2.

10
sounded to deactivate. NOTE: To test, a
cloth can be used to cover the alarm to
reduce risk of hearing damage.
Incorrect Code
If an incorrect code is entered the unit will
sound a louder beep and the indicator
light will flash red 3 times. Re-enter
correct code after indicator light stops
flashing.
OPERATING IN THE CHIME MODE
The chime is used to notify you when
motion is sensed in the area.
Slide switch to CHIME mode; the
chime will sound once.
Activating the Chime:
The chime will go off immediately
when motion is sensed. No code is
required. The motion sensor will retest
the area 15 seconds after chime
sounds.
1.
•