geo-FENNEL FSM 130 User manual

User’s Manual
Sound Level Meter

(1)Make the following buttons and function switch settings.
Display: dB, A, Hi or Lo, F
Function: A-Weighting
Response Time: FAST
Level range: 30 to 100dB(Lo) or 60 to 130dB(Hi)
Measurement mode: MAX Hold and Data Hold Mode
function disable.
(2) Insert the microphone housing carefully into the insertion
hole of the calibrator.
(3) Open battery cover and remove the battery to adjust the
CAL94dB potentiometer of the unit. The level display will
indicate the desired level.
Our products are all well calibrated before shipment
C O ntents
Title Page
I. Safety Information..............................................1
II. General Description............................................1
III. Specifications................….................................. 2
IV. Name And Functions.......................................... 4
V. Measurement Preparation .................…............ 7
VI. Operating Precautions....................................... 7
VII. Measurement ...................................................... 8
VIII￡
￡￡
￡Calibration Procedures..................................... 10
11

B
BB
B. Safety information
Read the following safety information carefully before attempting
to operate or service the meter.
Use the meter only as specified in this manual; otherwise, the
protection provided by the meter may be impaired.
Environment conditions
1 Altitude up to 2000 meters
2 Relatively humidity 90% max.
3 Operation Ambient 0~40@
Maintenance & Clearing
1 Repairs or servicing not covered in this manual should only
be performed by qualified personnel.
2 Periodically wipe the case with a dry cloth. Do not use
abrasives or solvents on this instruments.
Safety symbols
Meter is protected throughout by double insulation or
reinforced insulation.
When servicing, use only specified replacement parts.
Comply with EMC
C
CC
C. General Description
Thank you for using our Sound Level Meter. To ensure that you
can get the most from it, we recommend that you read and follow
the manual carefully before use.
VIII￡
￡￡
￡Calibration Procedures
Using a standardAcoustic Calibrator (94dB, 1kHz Sine wave)
1 10

(4) Hold the instrument comfortably in hand or fix on tripod and
point the microphone at the suspected noise source, the
sound pressure level will be displayed.
(5) When MAX (maximum hold) mode is chosen. The
instrument captures and holds the maximum noise level for
a long period using any of the time weightings and ranges.
(6) When HOLD (data hold )mode is chosen.The hold function
freezes the reading in the display. Press the HOLD button
momentarily to activate or to exit the HOLD function
(7) Turn OFF the instrument and remove and remove battery
when not in use.
This unit conforms to the IEC651 type 2, ANSI S1.4 type 2 for
Sound Level Meters.
This Sound Level Meter has been designed to meet the
measurement requirements of safety Engineers, Health,
Industrial safety offices and sound quality control in various
environments.
Ranges from 30dB to 130dB at frequencies between
31.5Hz and 8 KHz.
Display with 0.1dB steps on a 4-digits LCD.
With two equivalent weighted sound pressure levels, A and
C.
D
DD
D. Specifications
Standard applied : IEC651 type 2, ANSI S1.4 type 2
Frequency range : 31.5Hz~8KHz
Measuring level range : 30~130dB
Frequency weighting : A/C
Microphone
: 1/2 inch electret condenser microphone
Calibration
: Electrical calibration with the internal
oscillator (1kHz sine wave)
Display : LCD
Digital display : 4 digits
Resolution: 0.1dB
Display Up data: 0.5 sec.
Time weighting : FAST(125mS), SLOW(1 sec.)
Level ranges : Lo: 30-100dB
9 2

Hi : 60-130dB
Accuracy
: + 1.5dB (under reference conditions)
Alarm function : “OVER” is show when input is out of
range
Maximum hold : Hold readings the Maximum Value, with
decay < 1dB/3minutes.
Auto power off : Meter automatically shuts down after
approx. 15 minutes of inactivity.
Power supply
: One 9V battery, 006P or IEC 6F22 or
NEDA 1604.
Power life
: About 50hrs(alkaline Battery)
Operation temperature : 0 to 40@(32 to 104
o
F)
Operation humidity : 10 to 90%RH
Storage temperature
: -10 to 60@( 14 to 140
o
F)
Storage humidity
: 10 to 75%RH
Dimensions : 210(L)X55(W)X32(H)mm
230g(including battery)
Weight : 9V battery, carrying case, Instruction
manual..
(2) To achieve more accurate measurement, use an extension
cable to separate the Microphone from the main body so
that the effect of unexpected sound reflection can be
eliminated.
(3) Calibrate the instrument before operation if the instrument
was not in use for a long time or operated at bad
environment.
(4) Do not store or operate the instrument at high temperature
and high humidity environment.
(5) Keep microphone dry and avoid severe vibration.
(6) Please take the battery and keep the instrument in low
humidity environment. When not in use.
VII. Measurement
(1) Open battery cover and install a 9-volt battery in the battery
compartment.
(2) Turn on power and select the desired response Time and
weighting. If the sound source consists of short bursts or
only catching sound peak, set response to FAST. To
measure average sound, use the slow setting.
Select A- weighting for general noise sound level and
C-weighting for measuring sound level of acoustic material.
(3) Select desired Level
3 8

w
ww
wMAX/ Hold button MAX/HOLD
The max. Hold position is used to measure the maximum level
of sounds. The maximum measured level is up dated
continuously. Press once again the button, will release the hold
and allow a further measurement.
Data Hold button: Press and hold the Button for over 2
second to turn on or off data hold function.
The hold function freezes the reading in the display.
x
xx
xMicrophone
1/2 inch Electret Condenser microphone
y
yy
y
Battery Cover
V. Measurement Preparation
(1) Battery loading
Remove the battery cover on the back and put in one 9V
Battery.
(2) Battery Replacement
When the battery voltage drops below the operating voltage,
mark “BAT” appears. If it appears, battery should be
replaced with new one.
VI. Operating Precautions
(1) Wind blowing across the microphone would bring additional
extraneous noise.
Once using the instrument in the presence of wind, it is a
must to mount the windscreen to not pick up undesirable
signals.
V. Name and Functions
7 4

BAT
F
dB
S
p
pp
p!
!!
!Windscreen
If you operate at wind speed over 10m/sec, please put protective
accessories in front of the microphone.
q
qq
q!
!!
!Display
SYMBOL FUNCTION
LCD 4digits
MAX Maximum Value hold
OVER Over range
F Fast response
S Slow response
A A-Weighting
C C-Weighting
Lo Low Range (30~100dB)
Hi High Range (60~130dB)
BAT Low-Battery
r
rr
rPower ON/OFF button
Turn the meter power ON/OFF
s
ss
sBacklight Button:
Turn the meter backlight ON/OFF
t
tt
tA-weighting / C-weighting select button A/C
A: A – Weighting. For general sound level measurements.
C: C – Weighting. For checking the low- frequency content of
noise.
(If the C-Weighted level is much higher than the
A-Weighted level, then there is a large amount of
low-frequency noise)
u
uu
uTime weighting select button F/ S
F (fast response): for normal measurements (fast varying
noise)
S (slow response): for checking average level of
fluctuating noise
v
vv
vLevel range select button Lo/Hi
Lo: 30~100dB; Hi: 60~130dB
When “OVER” is indicated, the ranges switch to another
range for measurement.
5 6