Getinge CS100 User manual

Note: This is an abbreviated guide
for proper baery operation and
maintenance for the CS100 and CS300.
For complete product instructions,
please refer to the CS100 and CS300
Operating Instructions.
CS100/CS300 Baery Operation
Quick Reference Guide

2
CS100/CS300 BATTERY OPERATION
Intro
Introduction
This Quick Reference Guide is designed to highlight the location,
functionality, alarms and maintenance of the lead acid batteries that
accompany the CS100 and CS300 Intra-aortic Ballon Pumps.
The CS100 and CS300 batteries are designed to be used during transport
or portable operation and it is critical to keep these batteries charged at
all times to avoid interruption in power during transport. Additionally, it is
important to maintain the batteries in accordance with CS100 and CS300
Operating Instructions.
CS100 CS300

3CS100/CS300 BATTERY OPERATION
Table of Contents
Table of Contents
Section Page #
Baery Overview 4-6
Baery Status 7-14
CS300 Baery Operation 15-20
CS300 Baery Preventive Maintenance 21
CS100 Baery Operation 22-30
CS100 Baery Preventive Maintenance 31
Key Baery Warnings and Cautions 32

4
CS100/CS300 BATTERY OPERATION
CS100/CS300 Internal Battery Specifications
Baery Overview
Type: 24 VDC (nominal), 17.2 Amp-hours
Sealed lead acid, maintenance free
Run Time: (full charge) 2.25 hours minimum (from full charge, 120 bpm, 22 ± 5 °C)
Approximately 3.0 hours typical with new baery (from full
charge, 90 bpm, 22 ± 5 °C)
NOTE: A reduction in runtime can occur over a baery's life for reasons such as age,
storage temperature and discharge depth.
Recharge Time: 18 hours minimum (from complete discharge to full charge,
22 ± 5 °C), 8 hours to achieve at least 90 percent charge
(typically).

5CS100/CS300 BATTERY OPERATION
CS100/CS300 Battery Information
CS100/CS300 Batteries
The IABP includes a battery pack which contains two sealed lead acid
batteries. The batteries are maintenance free. There is no need to add
water or electrolyte. The batteries are sealed to prevent leakage from the
terminals or case.
Replace batteries as required. Batteries should be replaced after 100 full
discharge cycles, at no more than three (3) year intervals, or if run time is
less than the minimum run time of 135 minutes minimum at 120 bpm.
Disposal of batteries should be conducted in accordance with local
statutes and the labeling shown on the battery pack.
Baery Overview

6
CS100/CS300 BATTERY OPERATION
CS100/CS300 Optimum Battery Performance
To obtain optimum battery performance and expected battery life the following guidelines should be observed.
• The batteries should be maintained at full charge when the IABP is not in use. It is required that the IABP be plugged
into an AC outlet when the system is not in use. Verify the battery is charging by observing the charge indicator on
the pump module. If the unit must be stored for an extended time period (2 months or longer} and AC power is not
available to maintain the internal battery, or if the unit is stored in an ambient exceeding the maximum operating
temperature, disconnect the system battery pack from the system console. Due to battery self-discharge the
disconnected batteries must be fully recharged at least every four months.
• The battery contains a safety vent that will allow gases to be released should its rating be exceeded. If this vent is
actuated do not operate the unit and contact a qualified service representative.
• Do not short circuit the battery or battery pack terminals. Keep battery pack covers on at all times to avoid objects or
liquids falling on batteries.
• Excessive heat is very detrimental to battery life. Do not operate the system in ambients above the maximum
operating temperature.
• DO NOT attempt to repair the battery. If the case is cracked or terminal leads are broken replace with the same
rate battery.
• DO NOT disassemble battery. The battery contains an electrolyte which can injure skin or damage clothing. In the
event that electrolyte gets on skin or in eyes, immediately flush with water for 15 minutes and get prompt medical
attention.
• Batteries must be replaced as pairs, (i.e., same lot/date code).
• When a Low Battery message is displayed after any system operation, the battery should be recharged within several
hours to prevent battery damage
Baery Overview

7CS100/CS300 BATTERY OPERATION
Viewing Battery Status on Front Panel
Baery Status
IABP ON/OFF
This is the ON/OFF switch for the IABP console and monitor module. Operation of
this switch does not affect the status of the internal baery charger.
Baery Charging LED
This indicator has three states:
• It illuminates continuously when the internal baeries are fully charged
• The LED indicator flashes when the internal baeries are charging
• CS300: It is not illuminated when system is using the baery as a power source, or
when AC power is not available to the system, or when the system baery is faulty.
CS100: The Baery In Use status message and the Baery Indicator are displayed
when the system is operating from the internal rechargeable baery.
IABP ON/OFF
CS300
Automated Counterpulsation
INTELLIS ENSE TECHNOLO GY
Front Panel
Battery
Charging LED
FOR CS100:
CAUTION: The internal baeries are charging only when the
AC Mains plug is connected to an active AC Mains source,
the AC Mains switch is “On”, and the baery charging status
LED is illuminated. This charging condition must be maintained
even when the system is not in use. Note that 18 hours of charging
is required to fully charge the baeries.
FOR CS300:
CAUTION: The system should be configured to charge the
internal baeries whenever AC power is available. Hence, keep the
system connected to a live AC receptacle with the Mains On/Off
switch in the “On“position. If the system is to be stored for extensive
periods of time, or in ambient temperatures above the operating
range, see the Baery Section of the User Maintenance Chapter in
the Operating Instructions for additional information.
CAUTION: When AC power operation is intended, insure that the
system is plugged into AC mains, that the mains switch is in the “On”
position, and that the Baery in Use informational message in
NOT displayed.
It is extremely important to know the status of the IABP baeries at all times, as the status of the internal baeries affects the performance and
operation of the unit. There are two ways to determine the baery status, on the front panel and on the display screen.

8
CS100/CS300 BATTERY OPERATION
Viewing Battery Status on Display Screen
Baery Status
Note: The display shown is for
illustrative purposes and does not
represent actual clinical conditions.
Alarm and Advisory Messages Area
This section of the screen displays alarm and advisory messages. The top-most line is reserved
for high priority alarms. The lower three (3) lines are shared to display any medium/low level
alarms or informational messages. If more than one message is displayed, they are posted in
priority order. See Alarms and Advisory Messages on page 9 of this document, for more
information regarding priority. As conditions are corrected, the corresponding message is
cleared and the next highest priority alarm or informational message is displayed. Pressing
the HELP key will access the appropriate help screen for the displayed condition. See “Help
Screens” in the Operating Instructions for more information.
Baery Indicator Icon
This icon indicates the approximate charge remaining in the internal baeries.
This indicator is displayed only when the system is powered by the internal baeries.
NOTE: The Low Baery Medium Priority Alarm is displayed when less than 30 minutes (approximately) of
internal baery life remains. When this message appears, the baery symbol is displayed as empty and
starts flashing. See the Troubleshooting and User Maintenance Chapters in the Operating Instructions for
additional information.
TRIGGER
HEART RATE
bpm
MEAN
mmHg
AUG.
mmHg
AUG. ALARM
mmHg
SYSTOLIC
mmHg
DIASTOLIC
mmHg
IAB STATUS
PRESSURE
SOURCE
IAB FILL MODE
SLOW GAS
ALARM
•LEAD
•GAIN
ECG
OPERATION
MODE
ALARM &
ADVISORY
MESSAGES
Automated Counterpulsation
II
Normal
External
Auto
On
Auto
19 mm Auto
Threshold
80
94
40
72
Helium
115
94
120
80
40
0.5 mV
Infl. Defl.
0.0
Pressure
AUTO
Unassisted 99
Unassisted 51
22 min in
Standby
Check IAB Catheter
Battery In Use
Low Battery
Auto Zeroing
HELP Available for Alarm/Advisory Battery
!!
!!!
Off
Display Screen
Alarm & Advisory
Messages Area
Battery
Indicator Icon
Battery
Associated Help Screen
Probable Cause Corrective Actions
The IABP is being powered from the
internal baeries.
1. Verify that it is necessary to operate from the internal baery. If appropriate, switch to the AC power source.
2. Verify MAINS power switch, located above the AC power cord connector, is ON.
CAUSE AND RESPONSE:
Operation
Trigger Mode
Trigger
Source Detailed Cause System Response Reset
All All Indicates System is operating
from an internal baery.
Unaffected Message clears when power is received from AC power source.
BATTERY IN USE

9CS100/CS300 BATTERY OPERATION
Battery Alarms and Advisory Messages
Baery Status
The IABP utilizes both auditory and visual alarm signals to communicate the need for attention or awareness by the
pump operator. Auditory alarm signals (tone sequences) are primarily intended to attract the attention of the
operator. They were carefully developed to communicate the urgency of the response, as well as the pump’s location.
Auditory signals are effective over a relatively broad range of operator positions.
CAUTION: Do not set the alarm volume to such a low level that it cannot be readily heard over the ambient
noise level of the venue in which the IABP is used.
Visual alarm signals consist of both display panel symbols and text. The displayed information further reinforces the
urgency of the alarm (symbol shape, color & flashing property) and also identifies the alarm via a specific text
message. Textual information is legible at the operator’s position, up to 1 meter from the front of the display panel.
Additionally, alarms are further complimented by an option to display context sensitive help information to aid in the
understanding and guide in the resolution of the alarm condition.
Alarm and advisory messages are grouped into the following categories in order to facilitate operator awareness and
understanding:
• Technical Alarms
• High, Medium and Low Priority Alarms
• Informational Messages.
These messages are displayed based upon the priority of the condition(s) that prompted them. Technical Alarms and
High Priority Alarm messages are displayed in the top line of the Alarm and Advisory Messages section of the display.
Medium/low level alarms or informational messages are displayed in the 3 lines below the top line. When a Medium
Priority Alarm – such as a Battery Alarm – is displayed, IAB assist is not suspended and the Medium Priority Alarm
tone is sounded. Medium Priority Alarms require the Operator’s prompt response.

10
CS100/CS300 BATTERY OPERATION
Medium Priority Alarms
Baery Status
Medium Priority Alarms indicate situations in which a prompt Operator
response is required. This class of alarm does not suspend pumping but
may indicate a need for corrective action. A yellow flashing alarm icon with
two (2) exclamation points denotes Medium Priority Alarms.
All Medium Priority Alarms have a uniform audio tone. The combination
of three (3) notes for Medium Priority Alarms is played in the following
sequence: three notes apause and then this cycle repeats.
NOTE: A “Low Battery” is categorized as a Medium Priority Alarm.
!!
Medium Priority Alarm Icon