GLP IMPRESSION WWC STATIC User manual

Instruction Manual
from software version 1.00/30
(Instruction version 1.00)
e-mail: [email protected]
Internet: http://www.glp.de
W
W
W
W
W
W
C
C
C
&
&
&
C
C
C
C
C
C
W
W
W
S
S
St
t
ta
a
at
t
ti
i
ic
c
c

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 2
Preface
This manual serves for both systems the I IM MP PR RE ES SS SI IO ON N W WW WC C as well as the
I
IM MP PR RE ES SS SI IO ON N C CC CW W. . The two systems differ from each other only by the number of
cold- respectively warm- white LEDs.
WWC version: 30x LEDs cold white, 60x LEDs warm white
CCW version: 60x LEDs cold white, 30x LEDs warm white
Notes:

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 3
Table of content
1 Description of Device..............................................................................................4
1.1 Safety Instructions............................................................................................5
2 Preparation and Installation...................................................................................6
2.1 Mounting...........................................................................................................6
2.1.1 Mounting on the Floor (Upright)...........................................................7
2.1.2 Mounting in hanging Position (Head first)............................................7
2.1.3 Mounting in sidewise Position..............................................................8
2.2 Secure the Device ............................................................................................9
2.3 Connections......................................................................................................9
2.3.1 Power Supply.......................................................................................9
2.3.2 DMX.....................................................................................................9
3 The Menu Field......................................................................................................10
4 DMX Channel Selection (DMX Protocol) .............................................................11
5
5 Maintaining and Cleaning the I IM MP PR RE ES SS SI IO ON N.......................................................14
5.1 Safety regulations...........................................................................................14
5.2 Circumference and Interval (rule-of-thumb)....................................................14
6 Technical Specifications ......................................................................................15
7 Index.......................................................................................................................16

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 4
1 Description of Device
1. Moving head (actively and
passively cooled)
2. Arm with various cooling
vents
3. LCD-Display/Menu (data
entry)
4. Base with various
connectors and Camlock
mounting system
1
2
3
4
5
base side 1
6
base side 2
7
8
9
10
10
FUSET4A
5. Power On/Off
6. DMX- Output (3 pole)
7. DMX- Input (3 pole)
8. Micro-fuse 5x20mm, T4A
9. Mains supply (Powercon)
10.2x Safety eyes

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 5
1.1 Safety Instructions
The I IM MP PR RE ES SS SI IO ON N is a High-Tech Product. To guarantee a
smooth operation, it is necessary to respect the following rules.
The manufacturer of this device will not take responsibility of
damages through any disregard of the information in this
manual. Warranty claims also will be cancelled in case the
system casing is opened.
1. Make sure before putting the system into operation, that the fan and the air
inlets are clean and not blocked by anything.
2. It must be assured that the system-head can rotate unhindered throughout
his complete rotating range. A safety distance of at least 0.5 m to any easily
inflammable material (e.g. decoration material) must be adhered.
3. Attention! Don’t touch the device during the operation. This can cause
injuries or damages.
4. The system doesn’t contain any maintainable parts. Don’t open it!
5. It is necessary to wait at least 15 minutes after disconnecting the AC before
changing the optical carrier. Pay attention to possibly hot parts of the
system. -- Danger of BURNING --
6. Never look directly into the beam of light or one of the LEDs. Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M. You'll risk a serious injury of your eyes and in
particular of your retina.
Attention:
LED Class 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Hence: Avoid direct radiation of your eyes!
7. To allow a secure operation, follow also the Installation guide described in
chapter 2. Operating the I IM MP PR RE ES SS SI IO ON N without suitable safety aids like
Safety cables or clamps/hooks can increase the risk of an accident.
8. Repair-, maintenance- and installation work shall be done by qualified or
GLP certified staff only. You need to pay attention to the common rules of
technology that are not explicit mentioned in this manual.
9. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 6
2 Preparation and Installation
2.1 Mounting
The I IM MP PR RE ES SS SI IO ON N is fully operational whether it hangs or is mounted to the
wall. It can also be operated while standing on the floor. Keep a safety distance
of 0.5 m towards any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217.
The installation shall be done by qualified staff only.
For the various mounting positions of the I IM MP PR RE ES SS SI IO ON N(standing on the floor,
sideways or hanging) different accessories kits are available. Through this a
safe and firm installation is assured. You'll find special connectors on the
bottom side of the system which are put to use here. In addition the front side of
the system is marked with (FRONT) as this is important for a even orientation
during installation.

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 7
1x M10
(length max.16mm)
2x Camlock
quick release
fasteners
front side of the fixture
2.1.1 Mounting on the Floor (Upright)
To operate the I IM MP PR RE ES SS SI IO ON Nin an upright position, please use the
dedicated tripod which is mounted to the bottom side of the system. It is
fixed with fasteners called Camlock quick-release connectors. Turn the
two fasteners both 90° to lock them. Do the opposite to release them
again. On both sides you'll find eyelets to pull though a fixing strap. This
allows an additional bracing of the system during the upright operation.
2x Camlock
2x eyelets
2.1.2 Mounting in hanging Position (Head first)
To operate the I IM MP PR RE ES SS SI IO ON Nin an hanging position, please use a half-
coupler (clamp) which is mounted directly to the bottom side of the
system. It is fixed centrically with a M10x16 mm thread bolt.

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 8
M10x16
2.1.3 Mounting in sidewise Position
To operate the I IM MP PR RE ES SS SI IO ON Nin a sidewise position, please use an
addition mounting bar. Also this is fixed by two Camlock quick-release
connectors. Two half-couplers (clamps) are now used to mount the
system to a standard truss bar. This technique is necessary to cope with
the torque which accrues in this mounting position. In addition it allows a
concentrically position between two truss belts. Never use the "Mounting
in hanging Position" technique described above to fasten the system in
the sidewise position. A safe and sound installation can not be assured
in this way. This can also damage the system base.
2x 90°
Half-coupler (clamp) 1
Half-coupler (clamp) 2

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 9
without mounting bar
2.2 Secure the Device
Regardless of the mounting method of the I IM MP PR RE ES SS SI IO ON N you'll have to use a
stipulated safety wire. Therefore you have to pull the safety wire through to two
provided holes on the bottom side of the system and connect it with the truss-
support. Pay attention to a safe and proper fastening. Install a safety wire that
can hold at least 10 times the weight of the fixture. Never use the carrying
handles for this purpose.
The safety wire must be attached in a way that the height of drop is
minimised. A height of drop of more that 0.2m is strictly forbidden (

BGI
810-3).
2.3 Connections
2.3.1 Power Supply
~100-240 Volt AC, 50-60 Hz, earth contact type plug - Powercon
Connected load 350 VA (W) <=> T4A (micro-fuse 5x20mm)
Please see printing on the case for the right electronic supply!
Disconnect from the mains supply for changing the fuse and use
only the above described micro-fuse type.
2.3.2 DMX
USITT DMX-512 Standard input/output in 3 pole connectors.
3 pole: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+]
The DMX- Addressing starts at the DMX- Address [001].

W
W
WW
W
WC
C
C &
&
& C
C
CC
C
CW
W
W S
S
St
t
ta
a
at
t
ti
i
ic
c
c
GLP German Light Products GmbH (Instruction version 1.00) / from software version 1.00/30) 10
3 The Menu Field
You’ll find the control board on the side part of the arm. It allows you to
make all necessary adjustments of the I IM MP PR RE ES SS SI IO ON N. .With the Mode-
key you get into the main menu. Afterwards you can navigate through
the menu with the Up/Down-keys. Push the Enter-key to get in the next
menu level or to confirm your settings. Make them and set functions
ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key
(the display shows OK). Push the Mode-key to cancel the entry and go
back to the main menu.
Mode
Down
Enter
Up


MODE - ENTER 


Level1
Level 2
Level 3
Level 4
Remark
DMX Start
Address Define the DMX start address
Special Manual DMX
Manual control of all system functions
Special Activate the White- or Full-Power Mode; see also
DMX table
Dimmer Manual control for Dimmer

 
DOWN - UP 
 

Shutter Manual control for Shutter
1/3 White Manual control for 1/3 white, 30x LEDs (either
warm- or cold white depending on the system)
2/3 White Manual control for 2/3 white, 60x LEDs (either
warm- or cold white depending on the system)
Display
Contrast Adjustment for the Display contrast
Default Set Resetting all functions to original values
Set Dimmer
Frequency Changes PMW frequency between 600Hz and
1200Hz
Adjust
Key code
xxxx Use the code for entering the calibration menu (for
authorized persons only)
Clear
EEPROM Erase EEPROM memory
Diagnose Diagnose functions
Anz Ti0
-
Int
-
Err Internal data and function diagnosis
Dimmerwert
für DIM1 Internal data and function diagnosis
Dimmerwert
für DIM2 Internal data and function diagnosis
Dimmerwert
für DIM3 Internal data and function diagnosis
PFC
Voltage Shows the present PFC voltage
Temperature
Arm Indicates the arm temperature
Temperature
Head Indicates the head temperature
DMX Hold Defines whether the last DMX signal is stored or the
lamp is switched OFF in case of signal interruption
Position
Feedback Automatically position feedback (correction) for
Pan/Tilt movement
Set DMX
Image Stores the Scene currently sent to the unit