Goldmedal 2499-00-200 User manual

© 2020 Gold Medal Products Co.
Part No. 110280
Instruction Manual
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
Counter B.I.B. Dispenser
Model No. 2499-00-200

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 2
gmpopcorn.com
Table of Contents
SAFETY PRECAUTIONS ...................................................................................................................................3
INSTALLATION INSTRUCTIONS ...................................................................................................................5
Inspection of Shipment .......................................................................................................................................5
Manual.......................................................................................................................................................................5
Model Description.................................................................................................................................................5
Items Included with this Unit ...........................................................................................................................5
Setup...........................................................................................................................................................................5
Electrical Requirements .....................................................................................................................................6
Before You Plug In Machine ..............................................................................................................................6
Attaching the Butter Flavored Topping Bag ...............................................................................................7
OPERATING INSTRUCTIONS .........................................................................................................................8
Controls and Their Functions...........................................................................................................................8
Adjusting Dispense Settings..............................................................................................................................9
Prime Unit for Use..............................................................................................................................................10
Operating the Dispenser..................................................................................................................................10
Auto-Dispense Mode:..................................................................................................................................10
Manual Dispense Mode: .............................................................................................................................10
Care and Cleaning .................................................................................................................................... 11
Daily Cleaning Instructions ............................................................................................................................11
Sanitizing the Tubing and Pump ..................................................................................................................11
Troubleshooting....................................................................................................................................... 13
MAINTENANCE INSTRUCTIONS ................................................................................................................ 15
ORDERING SPARE PARTS............................................................................................................................ 16
Cabinet Front View –Parts Breakdown ....................................................................................................17
Cabinet Rear View –Parts Breakdown ......................................................................................................18
Tower View –Parts Breakdown...................................................................................................................20
Wiring Diagram ........................................................................................................................................21
WARRANTY...................................................................................................................................................... 22

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 3
gmpopcorn.com
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 4
gmpopcorn.com
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 5
gmpopcorn.com
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
2499-00-200 –Countertop pedestal style topping dispenser with an LED lighted sign, unit holds
one 35 lb. bag of butter flavored topping.
Items Included with this Unit
•Small Screwdriver (PN 55554), used for making pump adjustments
•Manual and Warranty Registration Card
Setup
1. Remove all packaging and tape.
2. Place unit on a sturdy, level surface.
3. Unit is preset at factory to dispense a measured amount of topping.
To adjust the dispense amount or speed, see Adjusting Dispense Settings in the
Operating Instructions.
4. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of
this manual).

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 6
gmpopcorn.com
Electrical Requirements
The following power supply must be provided (reference unit Data Plate for Wattage requirement):
120 V~, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle (reference unit Data Plate for model specific Volts AC, Hertz, and Wattage
requirements). We recommend this equipment be on a dedicated and protected circuit. Failure
to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal
Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The use of
extension cords is not recommended due to safety concerns, and may cause sacrificed and/or
reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure the power switch is OFF before plugging unit into receptacle.
2. Make sure wall outlet can accept the grounded plug on the power supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 7
gmpopcorn.com
Attaching the Butter Flavored Topping Bag
Use a maximum of 35 pound bag of topping for this unit.
IMPORTANT: This product is not intended for use with volatile food products
(i.e. real butter).
1. Remove the drip pan/insert and top cover from the holding pan base.
2. Remove the cap from the topping bag nozzle.
3. Attach the Universal Bag Connector (located in the holding pan) to the topping bag
nozzle (see steps below).
4. Place the topping bag in the unit. Be sure the connection end is put in first and is
located on the bottom side of the bag.
5. Replace the top cover, drip pan, and insert.
Step 2: Grasp the Bag Nozzle
and slide the Bag Connector
on from the side.
Step 3: With the hose connector
in place, press plunger forward
to lock.
Step 4: Connector shown
with plunger fully forward
in lock position.
Bag Nozzle
Plunger OUT in
open position
Universal Bag
Connector
Step 1: Pull the Universal Bag Connector’s plunger out until it clicks into the open position.
Steps to Attach the Universal Bag Connector

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 8
gmpopcorn.com
OPERATING INSTRUCTIONS
Controls and Their Functions
HEAT SWITCH (Power Switch): Three position rocker switch.
HEAT ONLY (up position)—activates the LED lights, unit heating (to maintain topping
temperature), and photo-eye sensor—pump is de-activated in heat only
setting.
CENTER position—power OFF
PUMP & HEAT (down position)—activates the pump, LED lights, unit heating (to
maintain topping temperature), and photo-eye sensor.
PUSH BUTTON PUMP SWITCH (Manual Dispense): Press the push button to manually
dispense topping continuously, release button to stop dispensing.
Note: When a push button is activated, the sensor is deactivated. When popcorn leaves the
photo-eye detection area, the sensor becomes active again.
TIMED SWITCH
Two modes are selectable (Timed and Not Timed). In either mode, sensor must detect
popcorn for 0.5 sec. before pump is automatically activated.
Note: To switch between Timed and Not Timed Modes, power the unit OFF for the mode
change to take effect.
Timed Mode –The pump turns on for a pre-determined length of time when photo-eye
detects a cup of popcorn. To adjust time, see Adjusting Dispense Settings section.
Note: The pump stops if popcorn is removed prematurely (if popcorn is brought
back within one second, the timer will resume and finish the timing period).
Not Timed Mode –The pump runs continuously as long as the photo-eye detects a cup
of popcorn.
PHOTO-EYE SENSOR (Auto-Dispense): Photo-eye must detect popcorn within about 5 inches
(13 cm) of the sensor for 0.5 sec. before pump is automatically activated (see image below
for sensor indicator lights).
Note: A slight delay is required after the popcorn is removed for the sensor to reactivate.
When wiping off the unit, shiny objects such as a watch can activate the photo-eye
at distances greater than 5 inches.
PUMP SPEED ADJUSTMENT: Use adjustment to set how fast topping is dispensed (see
Adjusting Dispense Settings on next page).
DISPENSE TIME ADJUSTMENT (Auto-Dispense): Use adjustment to set how long topping is
dispensed (settable from 3.0 to 9.4 sec.) (see Adjusting Dispense Settings on next page).
1 AMP FUSE: Protects pump from overload condition.

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 9
gmpopcorn.com
Adjusting Dispense Settings
To switch between Timed and Not Timed Modes, power the unit OFF for the mode change to
take effect.
Auto Dispense:
Timed Mode - Adjust the pump speed, pump time (from 3.0 to 9.4 sec.), or both.
Not Timed Mode - Adjust the pump speed only.
Manual Dispense: Adjust the pump speed only.
1. Use a small flat screwdriver to turn adjustment (located on rear control panel).
2. Turn clockwise to increase setting.
Turn counter-clockwise to decrease setting (full counter-clockwise is the lowest setting).
3. Test the setting.
1 AMP
Fuse
Power Switch
Pump Speed
Adjustment
Dispense Time
Adjustment
Push Button
Pump Switch
Push Button
Pump Switch
Green Indicator = sensor ready
Amber Indicator = popcorn detected
Photo-eye Sensor
(with Red indicator beam)
Rear Panel Controls
(use a small flat screwdriver to adjust Pump Speed or Time)
Photo-eye Sensor
Drip Pan/Insert
(sits in cover)
Timed
Switch

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 10
gmpopcorn.com
Prime Unit for Use
Prime the dispenser lines after adding topping.
1. Set Heat Switch to HEAT & PUMP.
2. To properly prime the unit—hold a
cup under nozzle and press a dispense
button until topping comes out in a
steady, bubble free liquid stream.
Operating the Dispenser
Prime the dispenser lines after adding topping, then unit is ready for dispensing. (For any sensor
issues and indicator light descriptions reference the Troubleshooting section.)
1. Set Heat Switch to HEAT ONLY for 30 minutes to allow topping to preheat—pump is
deactivated in this position.
2. After topping is warmed, set Power Switch to HEAT & PUMP.
3. Set Timed Switch to TIMED or NOT TIMED dispense mode.
Note: To switch between modes, power the unit OFF for the mode change to take effect.
4. Use Auto or Manual Dispense Mode shown below.
Auto-Dispense Mode:
1. Place popcorn about 5” (13 cm) under sensor.
2. Sensor will auto-detect popcorn and dispense
topping (sensor must see product for 0.5 sec. to
begin dispensing).
Note: A slight delay is required after popcorn is
removed for the sensor to reactivate.
To adjust the dispense settings, reference
Adjusting Dispense Settings section.
Manual Dispense Mode:
1. Place popcorn about 5” (13 cm) under nozzle.
2. Press and hold a dispense button for desired
amount of topping.
Note: If button is released before desired
amount is dispensed, remove popcorn
and wait 2 sec., then repeat step 2.
To adjust the dispense speed, reference
Adjusting Dispense Settings section.
3. Release button to stop dispensing.
Sensor
Indicator
Beam

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 11
gmpopcorn.com
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet.
Always unplug the equipment before cleaning or servicing.
025_111616
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners).
For surfaces needing further cleaning or degreasing, Watchdog Stainless Cleaner (Item No. 2088)
or Watchdog Concession Equipment Degreaser (Item No. 2580) is available for use accordingly.
For any cleaning products used, follow the manufacturer’s instructions on the product. DO NOT
use oven cleaners or abrasive materials as they will damage parts of machine.
Daily Cleaning Instructions
1. Turn machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. Lift the drip pan and insert from cover and wash them at the sink with mild soap and
warm water, then rinse and dry.
3. Wipe unit surfaces clean with a SLIGHTLY damp cloth (cloth may be SLIGHTLY
dampened with soap and water, then wipe again to remove any cleaner).
4. Nozzle is designed to be drip free. Butter flavored topping can accumulate and cause
the nozzle to clog.
If nozzle becomes clogged, use a paperclip or small diameter rod to clear the opening
(3/32” hole).
5. Reassemble the unit.
Sanitizing the Tubing and Pump
Items Needed: (2) Empty Pails, (1) Cleaning Bracket (Item No. 12594)
Gold Medal Chlor-Tech Sanitizer (Item No. 1109)
Medium Size Container (for priming unit)
1. Make sure the unit has cooled completely before attempting to clean.
2. Fill a clean bucket half-full with hot water and Gold Medal Chlor-Tech Sanitizer
(reference instructions on sanitizer container for appropriate amount).

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 12
gmpopcorn.com
3. Nozzle is designed to be drip free. Butter flavored topping can accumulate and cause
the nozzle to clog.
If nozzle becomes clogged, use a paperclip or small diameter rod to clear the opening
(3/32” hole).
4. Disconnect Universal Bag Connector from topping bag and connect it to cleaning
bracket as shown below. Make sure the plunger is engaged on pin.
5. Place hose with cleaning bracket into pail of sanitizing solution.
6. Place an empty pail under dispensing nozzle to receive cleaning solution pumped
through unit.
7. Use a dispense button to dispense solution until tubes are clean and free of topping.
8. When pumping is complete, discard dirty solution, clean the pail, and refill with clean
hot water.
9. Remove hose with bracket from solution pail and place it in the hot water.
10. Place an empty pail under nozzle.
11. Use a dispense button to dispense hot water until tubes are cleared of sanitizer.
12. When cleansing is complete, remove pail from dispenser.
13. Remove hose with bracket from hot water, disconnect bracket, and wipe hose and bag
connector dry.
14. Reconnect dispenser to bag of topping.
15. Purge and prime the lines—hold a measuring cup (or medium sized container) under
nozzle and press a dispense button until all water has been purged and tubes are
primed with topping. After cleaning, always discard the topping dispensed in priming.
16. Sanitize cleaning items for next use.
Cleaning
Bracket
Push Plunger IN to
lock onto bracket.
Plunger OUT in
open position.
Step 1:
Step 2:
Slide Connector
onto Bracket
Step 3:
Plunger ENGAGED on pin.

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 13
gmpopcorn.com
Troubleshooting
Issue
Possible Cause
Solution
No Power to the Unit
A. No power to the unit
A. Make sure unit is plugged in and Power Switch
is ON (green switch light should be ON). If
switch light does not turn on, have a qualified
electrician check the power supplied to unit.
Unit Does Not Dispense or
Delayed Dispense
A. Pump Fuse
A. Check fuse. If replaced and trips again, check
with a qualified service person for
inspection/repair.
B. Topping empty
B. Make sure there is topping in the bag.
Reference the Topping Installation section in
the Installation Instructions.
C. Clogged nozzle –Topping
can accumulate and cause
the nozzle to clog.
C. If nozzle becomes clogged, use a paperclip or
small diameter rod to clear the opening
(3/32” hole). Reference the Cleaning and Care
section.
D. Pump needs to be primed.
D. See Prime Unit for Use in the Operating
Instructions.
Unit Does Not Dispense or
Delayed Dispense
A. Sensor wait time in
Auto-Dispense Mode
A. Sensor must see popcorn within 5” of sensor
for 0.5 sec. to begin dispensing. A slight delay
is required after popcorn is removed for the
sensor to reactivate (reference, Operating the
Dispenser section).
B. Dispense delay in
Manual Dispense Mode
B. Unit dispenses continuously when dispense
button is held. If button is released, remove
popcorn and wait 2 sec. to reactivate the pump.
Sensor –Indicator Lights
C. Sensor faulty (sensor
indicators)
C. Check side of sensor for indicator lights. If an
indicator light does not come on as specified,
photo-eye may be faulty. Check with a
qualified service person for inspection/repair.
Green Indicator = sensor ready, powered
Automatic Mode: Popcorn must be
approx. 5” from photo-eye for sensor to
detect it.
Amber Indicator = object detected
Automatic Mode: Amber light turns on
when sensor detects popcorn for 0.5 sec.
(remove popcorn from sensor area for 2
sec. for sensor to reactivate).
Manual Mode: When dispense button is
pressed, control ignores photo-eye sensor
and manually dispenses.
Red Indicator Beam = photo-eye detection
Green Light = sensor ready
Amber Light = object
detected
Photo-eye Sensor
with Red indicator beam
(red beam shown enhanced
for reference purposes)

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 14
gmpopcorn.com
Issue
Possible Cause
Solution
Wrong Dispense Amount
A. Pump needs to be primed
A. See Prime Unit for Use in the Operating
Instructions.
B. Pump settings need
adjustment.
B. Pump Speed Adjustment: Use adjustment
on rear control panel to set how fast topping
is dispensed (see Adjusting Dispense Settings
section in the Operating Instructions).
Dispense Time Adjustment: Use adjustment
on rear control panel to set how long topping
is dispensed (settable from 0.2 to 2.0 sec.) (see
Adjusting Dispense Settings section in the
Operating Instructions).

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 15
gmpopcorn.com
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 16
gmpopcorn.com
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to Parts Department, Gold Medal Products Co., 10700
Medallion Drive, Cincinnati, Ohio 45241-4807
or place orders by phone or online:
Phone: [phone]
[phone]
Fax: [phone]
[phone]
E-mail: [email protected]
Web Page: gmpopcorn.com

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 17
gmpopcorn.com
Cabinet Front View –Parts Breakdown
1
4
3
2
20
19
See Tower View for
parts breakdown.
See Cabinet Rear View
for parts breakdown.
5
8
7
6
13
12
9
10
11
14
15
12
16
17
18
Item
Part Description
Part Number
2499-00-200
Item
Part Description
Part Number
2499-00-200
1
LID (storage tank cover)
114576
2
DRIP PAN
69148
3
DRIP PAN INSERT
69201
4
MAGNETIC CATCH
16141
5
PAN WELDMENT
114573
6
DISPENSE LABEL
114652
7
PUSHBUTTON SWITCH AMBER
55658
8
FOIL ELEMENT 300W 120V
39949
9
INSULATION WRAP (2 req’d)
38294
10
SCREW #8-32X3/8 PAN HD PH
74141
11
BOTTOM COVER
114574
12
8-32 SERRATED FLANGE NUT
61151
13
SPACER .180"ID X 1.030"LG (for
studs on pan weldment, 4 req’d)
88594
14
8-32 X 1 PH PAN M/S S.S.
12219
15
RUBBER FEET 3/4IN HIGH (4 req’d)
47155
16
UNIVERSAL BAG CONNECTOR
79100G
17
SINGLE WIRE HOSE CLAMP
75110
18
PLASTIC FOOD TUBING (sold by
the foot)
91375
19
1/4-20 X 1/2 P/H PHIL
12471
20
FLAT WASHER 1/4 STAINLESS
87261

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 18
gmpopcorn.com
Cabinet Rear View –Parts Breakdown
*CAUTION: If supply cord is damaged, it must be
replaced by Gold Medal Products Co., its service
agent, or similarly qualified persons in order to
avoid a hazard.
1
4
5
6
7
3
2
Tubing sold
by the foot.
Hose Clamp
(fastens tubing)
Small Screwdriver
(not shown, used for making
pump adjustments)
27
14, 15*
18
19
12
21
22
16, 17
23
20
24, 25
11
12, 13
10
9
8
Interior view shown without outer cabinet for parts reference only.
Wire Connector
(2, 3, or 5 position)
26

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 19
gmpopcorn.com
Cabinet Rear View –Parts List
Item
Part Description
Part Number
2499-00-200
1
PLASTIC FOOD TUBING (sold by the foot)
91375
2
HOSE CLAMP 7/16in - 1/2in
67843
3
8-32 X 1/4 PHIL PAN M/S
87314
4
PUMP BRACKET 2499 (2 required)
69157
5
GROMMET
69159
6
PUMP
79888
7
GROMMET
69158
8
BUSHING, SNAP 1.125 IN
82221
9
BUSHING, SNAP .875 IN
45396
10
BUTTER DISPENSE PCB
69175
11
POWER SUPPLY, 12VDC
55231
12
6-32 X 3/8 PHIL PAN M/S
39000
13
6-32 GRIP NUT ZINC PLATED
47517
14
STRAIN RELIEF SR-6P3-4
76026
15*
POWER SUPPLY CORD 15 AMP
22038
16
8-32 X 1/2 PH PAN W/SEMS (fastens ground)
47124
17
HEX NUT #8-32 STAINLESS (fastens ground)
89129
18
DECAL CONTROL FOR 2499A
69162
19
3 POSITION ROCKER SWITCH
39410
20
SWITCH, ROCKER SPDT
55050
21
REAR COVER
114575
22
SCREW #8-32X3/8 PAN HD PH (fastens cover)
74141
23
UNIV WARN LBL HORZ
115180
24
FUSEHOLDER
74636
25
FUSE, 1 AMP
79341
26
2 POSITION WIRE CONNECTOR
55621
3 POSITION WIRE CONNECTOR
55244
5 POSITION WIRE CONNECTOR
55245
27
SMALL SCREWDRIVER (not shown)
55554

Counter B.I.B. Dispenser Model No. 2499-00-200
Page 20
gmpopcorn.com
Tower View –Parts Breakdown
Item
Part Description
Part Number
2499-00-200
1
PUSHBUTTON SWITCH AMBER
55658
2
DISPENSER DECAL LABEL
114619
3
DISPENSE HEAD COVER
114630
4
12V LED SIDE EMITTING WHT
114618
5
DISPENSE HEAD BODY
114629
6
8-18 X 1/2 SS PH TYPE BT (fastens head cover)
114616
7
MOUNT BRACKET WELDMENT
114405
8
MALE ELBOW TUBE FITTING
114583
9
3/8IN SS TUBE 5IN LONG
114727
10
DISPENSER BODY WELDMENT
114104
11
8-32X1/2 FLANGE HEX SCREW (fastens bracket
to body weldment)
114770
12
MOUNT PLATE - PHOTO EYE
114408
13
8-32 X 1/2 PHIL PN M/S SS
42226
14
12V LED SPOT LIGHT
114617
15
NO DRIP SPOUT
114450
16
PHOTOELECTRIC SENSOR
69174
17
PLASTIC FOOD TUBING (sold by the foot)
91375
18
HOSE CLAMP 7/16in - 1/2in
67843
19
HEATED ROPE WIRE ASSY
39471
20
BUSHING, SNAP 1.500 IN
74621
8
9
10
7
3
5
6
2
1
4
LEDs (fitted in housing,
not shown)
Assembled View
15
16
12
17
14
15
16
12
11
18
Tubing sold by the
foot (not shown).
Hose Clamp
(fastens tubing)
13
20
19
Heated Rope for
pedestal tubing
(not shown).