Goldmedal 2666 User manual

6 Oz. Twin Pop
Popcorn MachineInstruction Manual
Model #2666
PartNo.16169
RevisedJune 1996
Cincinnati, OH 45241-4807 USA

SAFETY PRECAUTIONS

6 Oz. Twin Pop
MODEL #2666
1
INTRODUCTION
Your new 2666 Twin Pop is shipped completely assembled, ready to operate. After removing the
corrugated carton from the machine, check thoroughly for any damage which may have occurred
in transit. Claims should be filed immediately with the transportation company.
Remove all cardboard packing and tape from the machine. Wipe all exposed surfaces with a
damp cloth to remove fingerprints, smears, etc... which may have occurred during unpacking and
handling.
ELECTRICAL REQUIREMENTS
Standard voltage for the Twin Pop is 120V, 60 cycle, single phase, A.C. current. The unit should
be placed on its own 20 AMP electrical circuit. The switches to control the heaters, kettles, and
lights are located at the top on the inside of the cabinet.
CONTROLS
There are three switches on each side of the machine.
LIGHT AND WARMER SWITCH
Turns on heat to bottom corn pan and flood light.
KETTLE MOTOR SWITCH
Turns on motor which drives kettle agitator shaft.
KETTLE HEAT SWITCH
Turns on heat element.
AMOUNT OF POPCORN AND OIL CHARGE
Your new popper is equipped with a six ounce corn measure cup. We recommend flavored and
colored coconut oil. Popcorn popped in coconut oil stays fresher longer. Coconut oil does not
leave the black deposits in your kettle like other oils.
CORN CHARGE - 6 Ounces
OIL CHARGE - 2 Ounces
FLAVACOL - 1 Tablespoon

6 Oz. Twin Pop
MODEL #2666
2
POPPING INSTRUCTIONS
1. Turn kettle heat and kettle motor switch on.
2. Make test pop with 3 kernels of corn and 1 oz. of oil.
3. Load corn, oil charge, and seasoning into kettle.
4. When corn has popped dump kettle.
5. Repeat cycle starting with step 3.
6. Always pop three to five batches for best results.
CARE AND CLEANING
The aluminum frame of the popcorn machine is easy to keep clean. Usually a damp cloth will
remove all dirt and grease spots. NEVER USE ABRASIVES on the aluminum framework. The
glass should always be clean and sparkling. Remember the inside of the glass must be cleaned
too. Empty the old maid drawers and wipe clean. Remove bottom cabinet pans and clean out any
stray debris.

6 Oz. Twin Pop
MODEL#2666
3
ORDERING SPARE PARTS
1.Identify the desired part by checking it against the photos, illustrations, and/or the parts list.
2.When ordering, please include part number, part name, and quantity desired.
3.Please include your model name and machine serial number (located on the machine
nameplate) with your order.
4.Address all parts orders to: Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
or, place orders at:
(513) 769-767
Fax: [phone]
E-mail: [email protected]
NOTE:We do not ship glass, obtain replacement glass from your local glass shop or
hardware store. Always purchase double strength type glass. Sizes are:
FRONT GLASS 28 3/16" x 22 15/16" x 1/8"
SIDE GLASS 28 3/16" x 15 3/8" x 1/8"
MAINTENANCE INSTRUCTIONS
THE FOLLOWING SECTIONS OF THIS MANUAL ARE IN-
TENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO
ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE
NOT INTENDED FOR THE OPERATOR.
Adequate eye protection must be used when servicing this
equipment to prevent the possibility of injury.
Do NOT immerse the equipment in water.
Unplug your machine before servicing.

6 Oz. Twin Pop
MODEL #2666
4
6 Oz. RIGHT HAND KETTLE ASSEMBLY

6 Oz. Twin Pop
MODEL #2666
5
PARTS LIST - 6 Oz. R.H. KETTLE ASSEMBLY
Domestic
& Antique
Item No. Part No. Description
1-0 41742 Set Screw #10-32 x 3/16"
1-1 46649 Set Collar
1-2 47059 Spur Gear
1-3 47106 Needle Bearing
1-4 47107 C Ring
1-5 47120 Knob Lid Lift
1-6 49011 Stir Rod
1-7 49013 Agitator Weight
1-8 49016 Rear Kettle Lid
1-9 49423 Agitator Shaft Assembly
1-10 47053 Nut, Hex #10-24
1-11 47273 #16AWG Mgt. Nickel Wire
1-12 47298 Heat Element Retainer
1-13 47676 Kettle Thermostat
1-14 49075 Thermostat Bracket
1-15 49122 Bolt, 5/16-18 x 1" Sq Hd
1-16 49127 Lock Nut, Electric Conn.
1-17 49177 Screw, #8-32 x ¾" Hx Hd
1-18 49316 Kettle Shell
1-19 49317 Nut, Whiz Lock 5/16-18
1-20 49328 6 Oz Kettle Lead Assembly
1-21 46241 Connector 90 Degree
1-22 49086 Kettle Lead Wire, Red
1-23 49087 Kettle Lead Wire, White
1-24 49159 Kettle Lead Wire, Green
1-25 49329 Plug, 15A Twist Lock
1-26 49357 Heat Element, 850W
1-27 74135 Hex Nut, 5/16-18
1-28 74137 Washer, 5/16 Int Tooth
1-29 47001 Pop Rivet, Open End
1-30 47110 Knob, Dump Handle
1-31 47702 Nut, Acorn #8-32
1-32 49350 Conduit, Caution Label
1-33 89125 Screw, #8-32 x ¾" Hx Hd
RIGHT HAND DUMP KETTLE ONLY
2-6 49366 6 Oz. Steel Kettle Complete
2-7 49424 Agitator/Lid Assembly R.H.
2-8 49017 Front Kettle Lid R.H.
2-9 49367 6 Oz. Steel Kettle Bottom
2-10 49314 Dump Handle R.H.
2-11 49356 Kettle Crossbar R.H.

6 Oz. Twin Pop
MODEL #2666
6
PARTS LIST - 6 Oz. L.H. KETTLE ASSEMBLY
Domestic
& Antique
Item No. Part No. Description
1-0 41742 Set Screw #10-32 x 3/16"
1-1 46649 Set Collar
1-2 47059 Spur Gear
1-3 47106 Needle Bearing
1-4 47107 C Ring
1-5 47120 Knob, Lid Lift
1-6 49011 Stir Rod
1-7 49013 Agitator Weight
1-8 49016 Rear Kettle Lid
1-9 49423 Agitator Shaft Assembly
1-10 47053 Nut, Hex #10-24
1-11 47273 #16AWG Mgt. Nickel Wire
1-12 47298 Heat Element Retainer
1-13 47676 Kettle Thermostat
1-14 49075 Thermostat Bracket
1-15 49122 Bolt, 5/16-18 x 1" Sq Hd
1-16 49127 Lock Nut, Electric Conn.
1-17 49177 Screw, #8-32 x ¾" Hx Hd
1-18 49316 Kettle Shell
1-19 49317 Nut, Whiz Lock 5/16-18
1-20 49328 6 Oz Kettle Lead Assembly
1-21 46241 Connector, 90 Degree
1-22 49086 Kettle Lead Wire, Red
1-23 49087 Kettle Lead Wire, White
1-24 49159 Kettle Lead Wire, Green
1-25 49329 Plug, 15A Twist Lock
1-26 49357 Heat Element, 850W
1-27 74135 Hex Nut, 5/16-18
1-28 74137 Washer, 5/16 Int Tooth
1-29 47001 Pop Rivet, Open End
1-30 47110 Knob, Dump Handle
1-31 47702 Nut, Acorn #8-32
1-32 49350 Conduit, Caution Label
1-33 89125 Screw, #8-32 x ¾" Hx Hd
LEFT HAND DUMP KETTLE ONLY (not shown)
2-6 16133 6 Oz. Kettle L.H. Complete
2-7 16134 Agitator/Lid Assembly L.H.
2-8 16132 Front Kettle Lid L.H.
2-9 49314LH Dump Handle L.H.
2-10 16136 6 Oz. Steel Kettle Bottom
2-11 16130 Kettle Crossbar L.H.

6 Oz. Twin Pop
MODEL #2666
7
CABINET ASSEMBLY

6 Oz. Twin Pop
MODEL #2666
8
Domestic Antique
Item No. Part No. Part No. Description
3-0 16140 16152 Cabinet Assembly 2666
3-1 16101 16149 Top Frame
3-2 16103 16143 Bottom Frame
3-3 16105 16105 Divider Panel
3-4 16160 16160 Drop Panel, R.H.
3-5 16163 16163 Drop Panel, L.H.
3-6 16114 16114 Corn Pan, R.H.
3-7 16116 16116 Corn Pan, L.H.
3-8 16139 16139 Magnetic Catch Bracket
3-9 16144 16144 Element Box, L.H.
3-10 16147 16147 Element Box, R.H.
3-11 16145 16145 Old Maid Pan
3-12 16146 16146 Element Bracket
3-13 41013 41013 Door Knob
3-14 41349 41349 Male Hinge, R.H.
3-15 41350 41350 Male Hinge, L.H.
3-16 41351 41351 Female Hinge, R.H.
3-17 41352 41352 Female Hinge, L.H.
3-18 47178 47309 Corner Post, Front
3-19 47179 47310 Corner Post, Right Rear
3-20 47180 47311 Corner Post, Left Rear
3-21 47236 47236 Bushing Snap
3-22 47237 47237 Door Striker
3-23 47328 47328 Glide
3-24 47339 47339 Front Glass
3-25 47340 47340 Side Glass
3-26 47389 47389 Bottom Cover
3-27 47592 47592 Glass Retainer, Rear
3-28 47593 47593 Glass Retainer, Front
3-29 47600 47600 Door
3-30 47692 47692 Rigid Channel, 15 3/8"
3-31 47694 47694 Rigid Channel, 22 7/8"
3-32 47697 47697 Rigid Channel, 27 13/16"
3-33 76026 76026 Strain Relief
3-34 87148 42366 Lead-in Cord, 20 Amp
3-35 16106 16106 Divider Rail, Top
PARTS LIST - CABINET ASSEMBLY

6 Oz. Twin Pop
MODEL #2666
9
Domestic Antique
Item No. Part No. Part No. Description
4-0 16161 16161 Complete Hanger Assembly
4-1 13157 13157 Reflector Flood Light
4-2 16119 16119 Motor Mount Plate
4-3 16141 16141 Magnetic Catch
4-4 16142 16154 Dome Spacer
4-5 41033 41033 Pilot Light, 120V
4-6 40589 40589 Light Shield, Conical
4-7 47047 47047 Lamp Holder
4-8 47057 47057 Motor
4-9 47059 47059 Spur Gear
4-10 47065 47065 Gear Box
4-11 47201 47201 Switch
4-12 47202 47202 Switch, Motor/Light
4-13 47282 47282 Bushing - Snap
4-14 49009 49009 Hanger Arm, Rear
4-15 49010 49010 Hanger Arm, Front
4-16 49099 49099 Switch Box
4-17 49116 49116 Switch Label
4-18 49330 49330 Receptacle, 15A Twist Lock
4-19 49440 49440 Strip, Heat Element 50W
4-20* 16167 Dome
4-21
4-22 16164 Dome Frame Gold
4-23 16166 Inspection Cover
4-24 47771 Screw, #8 x 3/8" Hx Hd
4-25 16093 16093 Sign
4-26 16097 16097 Front Wrapper Assembly
4-27 16098 16098 Main Wrapper
4-28 16099 16099 Support Angle
4-29* 39016 39016 Fluorescent Light Tube
4-30* 41020 41020 Light Tube Holder
4-31* 41021 41021 Light Tube Holder Starter
4-32* 41022 41022 Light Ballast
4-33* 41023 41023 Light Starter
4-34* 47578 47578 Wire Cloth
4-35* 61007 61007 Molded Wire Harness
* Items Not Shown
PARTS LIST - CABINET ASSEMBLY (continued)

6 Oz. Twin Pop
MODEL #2666
10
ELECTRICAL SCHEMATIC

WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, volt-
age, abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
ORIMPLIED,ANDOFALLOTHEROBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIP-
TION ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASERFIRSTCALLSGOLDMEDALPRODUCTSCOMPANY AT 1-800-
428-2676 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIP-
MENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERN-
ING THE REPAIR OR REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, OH 45241-4807 USA