Grandstream Networks GXP-285 User manual

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 1
Grandstream
IP Phone
Configuration Guides
Yeastar Technology Co., Ltd.

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 2
Index:
1 For Grandstream GXP-2000 ....................................................................... 3
1.1 Register with MyPBX......................................................................... 3
2 For GrandStream Handytone 386 ............................................................... 5
2.1 How to setup ATA for FAX ................................................................. 5
3 For GrandStream HandyTone 486(487), 286(287), ATA ................................ 7
3.1 How to setup ATA for MyPBX: ............................................................ 8

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 3
For Grandstream GXP-2000
Important
This guide has been tested for Grandstream phones with firmware version 1.2.4.3.
Be aware that different firmware revisions may have different web interface formats
and functionality.
This guide is applicable to the following Grandstream phone models GXP 280, 285,
1200, 2000, 2010, 2020. You can follow this guide to manually configure your
phone.
Register with MyPBX
Configuring the Phone to Register with MyPBX
1. Start up the phone and identify its IP Address from the LCD display. For this
example we will assume the IP Address of the phone is 192.168.5.126, and the
IP Address of MyPBX is 192.168.5.150
2. Point your browser to the web interface of the phone: http://192.168.5.126.
The default password is ‘admin’.
3. We now need to set the phone to register with MyPBX. Go to the ‘Account 1’
page:
Figure 1-1
1) Set the ‘Account Active’field to ‘yes’
2) Set the ‘Account Name’field to a name (for informational purposes only)
3) Set the ‘SIP Server’field to the IP Address of MyPBX
4) Set the ‘SIP User ID’field to the extension number you want to associate
with this phone
5) Set the ‘Authenticate ID’field to the extension's number
6) Set the ‘Authenticate Password’field to the extension's Password
7) Set the ‘Name’field to the name you would like to be displayed on other
phones when calling out
8) Set the ‘User ID is phone number’field to ‘yes’

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 4
9) Set the ‘Auth Answer’field to ‘no’and the ‘Allow Auth Answer by Call-Info’
field to ‘yes’(to allow paging functionality)
Figure 1-2
10) Click the ‘Update’button at the bottom of the page, and then click the
‘Reboot’button. Your phone will restart. After rebooting, the phone will
retrieve its configuration files and register with MyPBX. This can be verified
via the ‘Extension Status’page of MyPBX Management Console.

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 5
For GrandStream Handytone 386
How to setup ATA for FAX
Follow these steps to set up a GrandStream HandyTone 386 VoIP ATA with MyPBX:
1. Connect the device’s LAN port to your computer with a straight network cable.
2. The device is preconfigured with IP Address 192.168.5.126. Configure your
computer to have static IP Address 192.168.5.126, with subnet mask
255.255.255.0.
3. Launch a browser and go to http://192.168.5.126. The default username is
‘Admin’.
4. Select the ‘Basic settings’tab.
Figure 2-1
5. If your network has a DHCP Server, then select the radio button labeled
‘dynamically assigned via DHCP’.
6. If your network does NOT have a DHCP Server, then set up static IP Addressing.
From this point onwards, we will assume that the IP Address of MyPBX Server
on the network is 192.168.5.150, the IP Address of the device will be
192.168.5.150, the IP Address of the default gateway is 192.168.5.1, and the
IP Address of the DNS Server for the subnet is 10.25.0.168.
7. Scroll to the bottom of the page and click the ‘Update’button. You will be
prompted to reboot the device. Click the ‘Reboot’button. After the device has
finished rebooting, you may consult the DHCP Server’s administrative tools to

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 6
retrieve the device’s new IP Address.
8. Now that you have access to the web configuration you can start configuring it
against MyPBX. Launch a browser and point it to device’s new IP Address.
9. Ensure that you have already created the extension in MyPBX. Take note of the
Authentication ID field and the Authentication password that you have entered
for the extension connected to the ATA device.
10. Go to ‘FXS PORT 1’tab.
Figure 2-2
11. Set the ‘SIP Server’field to the IP Address of the server on which MyPBX is
installed –in this example 192.168.5.150.
12. Set the ‘Outbound Proxy’field to the same value as in step 11.
13. The ‘SIP User ID’field should match the ‘Extension Number’field of the
extension in MyPBX Management Console.
14. The ‘Authenticate ID’and ‘Authenticate Password’fields must match the
Authentication ID and Password set for that extension in MyPBX Management
Console.
15. The ‘Name’field is optional. A suitable value would be the name of the user
using this phone.
16. Set ‘User ID is phone number’to ‘Yes’
17. Set ‘Sip Registration’to ‘Yes’
18. Set ‘Unregister on Reboot’to ‘Yes’
19. Set the ‘Register Expiration’field to a suitable value. For testing purposes you
may want to use 60 seconds, but once the configuration is tested a larger value
would be more appropriate to limit unnecessary network traffic. A good setting
for general use could be 3600 seconds (1 hour).

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 7
20. Set ‘Enable Call Features’to ‘Yes’. This setting enables feature like transfer, on
hold etc from the analog phone connected to the FXS port of the device.
21. Set the ‘Preferred Vocoder’to choice 1: PCMU, choice 2: PCMA. The settings for
choices 3 to 6 will not come in use since they will not be used by MyPBX.
22. Set ‘Allow outgoing call without Registration’to ‘yes’.
23. Scroll to the bottom of the page and click the ‘Update’button. You will be
prompted to reboot the device. Click the ‘Reboot’button.
24. Repeat steps 11-24 for the configuring ‘FXS port 2’.
25. After the HandyTone has restarted, switch to MyPBX Management Console, and
click on ‘Line Status’, your new extension connected to the PBX should be listed
with a blue status light.
For GrandStream HandyTone
486(487), 286(287), ATA
Configuring GrandStream HandyTone 486(487), 286(287), ATA for
MyPBX
Important
This guide has been tested with firmware version 1.1.0.37. Be aware that different
firmware revisions may have different web interface formats and functionality. This
is based on a new ATA OR one that has been reset to factory defaults.

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 8
How to setup ATA for MyPBX:
Connect the LAN to the WAN port of the HandyTone
1. Connect an analog phone to the HandyTone phone port. Pick up the headset
and press ‘****’. This will start up a Voice Prompt Menu. Now press ‘02’to listen
to the IP address that was assigned to the device by the DHCP server
2. Enable the wan side Web access, dial ‘****’and then ‘129’
3. Launch a browser and go to the IP Address, The default username is ‘admin’,
Select the ‘Advanced Settings 1’tab.
Figure 3-1
4. Set the ‘SIP Server’field to the IP Address of the server on which MyPBX is
installed –in this example 192.168.5.150
5. Set the ‘Outbound Proxy’field to the same value as sip server
6. The ‘SIP User ID’field should match the ‘Extension Number’field of the
extension created for this phone in MyPBX Management Console
7. In the ‘Authenticate ID’and ‘Authenticate Password’fields must match the
‘extension’and ‘Password’set for that extension in MyPBX Management
Console
8. The ‘Name’field is optional. A suitable value would be the name of the user
using this phone
9. Set the ‘Preferred Vocoder’to choice 1: PCMU, choice 2: PCMA. The settings for
choices 3 to 7 will not come in use since they will not be used by MyPBX
10. Set ‘payload type’to 101 for successful registration
11. Set ‘User ID is phone number’ to ‘Yes’

Grandstream IP Phone Configuration Guides
www.yeastar.com Page 9
12. Set ‘Sip Registration’to ‘Yes’
13. Set ‘Unregister on Reboot’to ‘Yes’
14. Set the ‘Register Expiration’field to a suitable value. For testing purposes you
may want to use 60 seconds, but once configuration is tested a larger value
would be more appropriate to limit unnecessary network traffic. A good setting
for general use could be 3600 seconds (1 hour)
15. Set ‘Allow outgoing call without Registration’to yes
16. Set ‘Enable Call Features’to ‘Yes’. This setting enables features like transfer, on
hold etc from the analog phone connected to the FXS port of the device
17. Scroll to the bottom of the page and click the ‘Update’button. You will be
prompted to reboot the device. Click the ‘Reboot’button
Figure 3-2
18. After the HandyTone has restarted, switch to MyPBX Management Console, and
click on ’Line Status’. In the section ‘Extensions’, your new extension connected
to the PBX should be listed with a blue status light
<Finish>