Guardian Fall Protection 01500 User manual

Product Name: Rope Grab
Instruction Manual
Part #: 01500; 01503; 01505; 01506; 01507; 01508; 01509; 01511
Do not throw away these instructions!
Read and understand these instructions before using equipment!
Introduction 1
Applicable Safety Standards 1
Worker Classifications 1
Safety Information 6 - 7
Product Specific Applications 2
Limitations 2 - 3
Components and Specifications 3
Maintenance, Cleaning, and Storage 5
Inspection 5
Installation and Use 4 - 5
Inspection Log 6
Labels/Markings 7

Introduction
Thank you for purchasing a Guardian Fall
Protection Rope Grab. This manual must be
read and understood in its entirety, and
used as part of an employee training
program as required by OSHA or any
applicable state agency.
This and any other included instructions
must be made available to the user of the
equipment. The user must understand how
to safely and effectively use the Rope Grab,
and all fall safety equipment used in
combination with the Rope Grab.
User Information
Date of First Use:
Serial #:
Trainer:
User:
Applicable Safety Standards
When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926
Subpart M and OSHA 1910 standards for fall protection. Applicable standards and regulations depend on the
type of work being done, and also might include state-specific regulations. Consult regulatory agencies for
more information on personal fall arrest systems and associated components.
Worker Classifications
!
CAUTION
Understand the following definitions of those who
work near or who may be exposed to fall hazards.
Qualified Person: A person with an accredited degree or certification, and with extensive experience or
sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall
protection and rescue systems.
Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be
responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,
and application. A person who is proficient in identifying existing and predictable fall hazards, and who has
the authority to stop work in order to eliminate hazards.
Authorized Person: A person who is assigned by their employer to work around or be subject to potential or
existing fall hazards.
It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all
applicable safety regulations are complied with.
Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
1

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
2
Product Specific Applications
Restraint: Rope Grabs may be used in Restraint applications. Restraint systems prevent workers
from reaching the leading edge of a fall hazard. Always account for fully deployed length of
lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system of
at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces with
slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side, Shoulder.
!
WARNING
Use of equipment in unintended applications may result in serious
injury or death. Maximum 1 attachment per connection point.
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is 130-310 lbs.
Limitations
Fall Clearance: There must be sufficient
clearance below the anchorage connector
to arrest a fall before the user strikes the
ground or an obstruction. When calculating
fall clearance, account for a MINIMUM 2’
safety factor, deceleration distance, user
height, length of lanyard/SRL, harness
stretch, and all other applicable factors.
Diagram shown is an example fall
clearance calculation ONLY.
Swing Falls: Prior to installation or use, make
considerations for eliminating or minimizing
all swing fall hazards. Swing falls occur when
the anchor is not directly above the location
where a fall occurs. Always work as close to in
line with the anchor point as possible. Swing
falls significantly increase the likelihood of
serious injury or death in the event of a fall.
Personal Fall Arrest: Rope Grabs may be used to support a MAXIMUM 1 Personal Fall Arrest System
(PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the directions
permitted by the system of at least 5,000 lbs. Maximum free fall is 6‘. Maximum distance between
harness D-ring and fall arrester is 36”. Applicable D-ring: Dorsal.
Fall clearance calculation shown based on standing
worker falling directly in-line with anchor point.
Always consider potential swing fall and other
hazards when calculating fall clearance.
*Eliminate Swing Fall whenever
possible! If Swing Fall exists,
always account for additional
fall clearance.
2’

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
3
Components and Specifications
Compatibility: When making connections with Rope Grab, eliminate all possibility of roll-out. Roll-out occurs
when interference between a hook and the attachment point causes the hook gate to unintentionally open
and release. All connections must be selected and deemed compatible with Rope Grab by a Competent
Person. All connector gates must be self-closing and self-locking, and withstand minimum loads of 3,600 lbs.
See the following for examples of compatible/incompatible connections:
Materials: galvanized steel or stainless steel, nylon, and polyester.
Part # Description
01500
01503
Trailing Rope Grab w/18” Extension Lanyard
01505
01506
01507
01511
Trailing Rope Grab w/3’ Shock Absorbing Extension Lanyard
Trailing Rope Grab (No Extension)
Removable Rope Positioning Device (No Extension)
Trailing Rope Grab w/18” Shock Absorbing Extension Lanyard
Stainless Steel Trailing Rope Grab
01509
01508
Stainless Steel Rope Grab (No Extension)
Rope Grab (No Extension)
Connector
closed and
locked to
D-ring. OK.
Connector
to integral
lanyard.
NO.
Two or more
snap hooks or
carabiners
connected to
each other. NO.
Two connectors
to same
D-ring. NO.
Connector
directly to
horizontal
lifeline. NO.
Connector
directly to
webbing.
NO.
Incompatible
or irregular
application,
which may
increase risk
of roll-out. NO.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
4
Installation and Use
01500 01505 01506
01503
01511
Prior to installation:
1. Robe Grab for use in combination with compatible vertical lifeline (VLL). Ensure VLL on which Rope Grab is
to be installed is compliant with all applicable OSHA and ANSI regulations.
• Compatible with 5/8” rope diameter only.
!
WARNING NEVER use with incompatible lifelines.
2. Eliminate all risk of lower end termination. Either ensure VLL will prevent user from striking next lower level
and that there is always adequate fall clearance, or that VLL will not reach the leading edge of any fall hazard
when used at its full length. NEVER tie knots in VLL, except at extreme bottom of lifeline in order to prevent
Rope Grab from detaching.
3. Eliminate or minimize all risk of swing fall.
Installation:
1. Attach Rope Grab to compatible VLL, ensuring Positioning Arrow is pointed up towards VLL anchorage.
2. Ensure Rope Grab is fully closed and locked to VLL.
01507
01508 01509

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
5
Maintenance, Cleaning, and Storage
If Rope Grab fails inspection in any way, immediately remove it from service, and contact Guardian to
inquire about its return or repair.
Cleaning after use is important for maintaining the safety and longevity of Rope Grab. Remove all dirt,
corrosives, and contaminants from Rope Grab before and after each use. If Rope Grab cannot be cleaned
with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean Rope Grab with corrosive
substances.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,
or other degrading elements.
Prior to EACH use, inspect Rope Grab for deficiencies, including, but not limited to, corrosion, deformation,
pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating, alteration, and
missing or illegible labels. IMMEDIATELY remove Rope Grab from service if defects or damage are found, or
if exposed to forces of fall arrest.
Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,
cracking, and hazardous materials. Ensure that selected work area will support the application-specific
minimum loads set forth in this instruction manual. Work area MUST be stable.
At least every 12 months, a Competent Person other than the user must inspect Rope Grab. Competent
Person inspections MUST be recorded in inspection log in instruction manual and on equipment
inspection grid label. The Competent Person must sign their initials in the box corresponding to the
month and year the inspection took place.
During inspection, consider all applications and hazards Rope Grab have been subjected to.
Inspection
For part # 01506,
transition between
trailing and
positioning
functionality
by releasing
tension lever.
Trailing
1.
2.
Positioning
3. Depending on Rope Grab part #, attach complete and compatible PFAS to Rope Grab connection point, or
attach extension lanyard/shock absorber to applicable harness D-ring. Always ensure maximum distance of
lanyard between Rope Grab and applicable harness D-ring does not exceed 36”.
4. Ensure Rope Grab always travels along VLL as worker moves across work surface.
• For part # 01506, when used as positioning device, lift up D-ring to reposition along VLL.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
6
Safety Information
Failure to understand and comply with safety regulations may result in
serious injury or death. Regulations included herein are not all-inclusive,
are for reference only, and are not intended to replace a Competent
Person’s judgment or knowledge of federal or state standards.
!
WARNING
Inspection Log
If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.
Do not alter equipment. Do not misuse equipment.
Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,
machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent
Person before fall protection equipment is selected.
The analysis of the workplace must anticipate where workers will be performing their duties, the routes they
will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall
protection equipment must be chosen by a Competent Person. Selections must account for all potential
hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused
condition.
Fall protection systems must be selected and installed under the supervision of a Competent Person, and used
in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,
and safety regulations. Forces applied to anchors must be calculated by a Competent Person.
Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.
No free fall allowed for non-LE SRLs. Class A SRLs must arrest falls within 24”; Class B SRLs must arrest falls
within 54”.
User must inspect prior to EACH use. Competent Person other than user must complete formal
inspection at least every 12 months. Competent Person to inspect and initial.
Date of First Use: __________________. Product lifetime is indefinite, as long as product passes all
inspection requirements.
This inspection log must be specific to one Rope Grab. Separate inspection logs must be used for each
Rope Grab. All inspection records must be made visible and available to all users at all times.

Guardian Fall Protection 6305 S. 231st St., Kent, WA 98032 phone: [phone] fax: [phone] www.guardianfall.com
785072 (Rev. K)
Labels/Markings
Rope Grab Markings:
Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of
compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied
in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be
self-locking and self-closing, and must never be connected to each other.
A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The
rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt
rescue. Store rescue equipment in an easily accessible and clearly marked area.
Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment
must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize
the likelihood of fall hazards, and the correct use of personal fall arrest systems.
NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless
explicitly certified for such use.
Equipment subjected to forces of fall arrest must immediately be removed from use.
Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there
is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of
equipment. Pregnant women and minors must not use this equipment.
Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension
may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.
UP
HAUT
AUF
ALTO
Automatic functioning
For dorsal attachment only
Y N-630 ADP ANSI Z359.1(07)
19 WPD
For Rope Size
5/8 Dia. (Ø16mm)
BREAKING STRENGTH
Résistence à le rupture
6000 LBS (27kN)
MAX : 30”/750mm(CSA), 36”(ANSI)
WARNING/AVERTISSMENT!
MANUFACTURER’S INSTRUCTIONS MUST BE
READ AND UNDERSTOOD PRIOR TO USE.
LES INSTRUCTIONS DU FABRICANT DOIVENT
ÉTRE LUES ET COMPRISES AVANT L’UTILISATION.
ANSI Z359.12
Z259.2.5
ASG