Häfele DL6500 User manual

www.hafele.com
User manual
Model DL6500
Digital door lock
DL6500
* The contents of this user manual are subject to change without prior notice
to the user in order to enhance performance of the products.

Product features
Read before using
Three way solution
Three electronic locking modes: PIN code, APP and
emergency key.
3
Master PIN code/ User PIN code identification
1 master PIN code, up to 20 user PIN codes.
Alarm for battery replacement time
When the power of the battery is too low a warning signal will
appear on the screen.
Please replace all batteries immediately.
Prevent mischief and hacking
When entering 10 times a wrong user PIN code, the lock is
suspended for 3 mins. After that, the lock will activate again.
While the lock is suspended, the screen will flash when you
are trying to use the keypad.
Random security coding function
Arandom number can be added before or after the real
user PIN code but the maximum length is 20 digits.
This feature will prevent the real user PIN code from
being exposed.
Warnings
* Read and understand all instructions before use.
* If damage is caused by failure to follow this instructions, the warranty
does not apply.
* Only use alkaline batteries.
* Do not expose the product and accessories to rain or water.
* Do not expose the product to corrosive substances to avoid damage
to the protective cover.
* When cleaning the product, please wipe it with a soft cloth.
* If there is a low battery alert, please replace all the batteries in time
and make sure they are properly installed.

Product specifications
Read before using
1. You can follow the voice guide by multi-language (English/Spanish/Portuguese/French/Chinese).
2. Master PIN code(4~10 digits): Default master PIN code is “12345678”, please modify it after installation.
3. User PIN code(4~10 digits): Maximum capacity is 20 .
Outside panel
Key cylinder
Touch keypad
Emergency power port
Reboot button
Inside panel
Battery cover
Network module
socket
Reset button
Manual mode switch

Factory default settings Quick setup guide
Read before using
Settings
Master PIN code*
Speaker
Wrong code entry limit
Shutdown time
Voice guide language
Factory defaults
12345678
Enabled
10 times
3 minutes
English
Master PIN code
Star key, return to previous menu
User PIN code
Touch the screen to activate lock
*Important: First step is to set your own master PIN code.

How to change master PIN code
Before changing default master PIN code, all other setting menu will be disabled.You have to change master PIN code first,
then do other lock settings.
How to add user PIN codes
1. When registering user PIN codes, the code must be entered within 10 seconds.
2. At any time you can return to the previous menu by pressing the “*” key.
(confirm)(4–10 digits) (4–10 digits)
(first setting use 12345678) (confirm)
(4–10 digits)
Add/Change access data
Lock operation

Delete access data
Additional lock features
Lock operation
How to delete user PIN code
(4–10 digits) (4–10 digits)
1. When deleting user PIN codes, the user number must be entered within 10 seconds.
2. At any time you can return to the previous menu by pressing the “*” key.
3. Deleting all user PIN codes can only be done by resetting the lock to factory default settings.
Language & Silent mode settings
English Spanish Portuguese
French Chinese Silent Mode
or or or or or
(4–10 digits)

Lock operation
Network module (Optionally available)
Log off network
Join network
Bluetooth settings
Disable Bluetooth
Enable Bluetooth
1. The default setting for Bluetooth is disabled.
2. Bluetooth will shut down in 2 mins after touch keypad lights off for energy saving, it will back to work when touch keypad wakes up.
(4–10 digits)
7
(4–10 digits)
7
(4–10 digits)
8
(4–10 digits)
8
Additional lock features

Additional lock features Menu table
Lock operation
Manual mode
Manual mode switch
1. Enable: Move the switch
to position to enable
manual mode.
2. Disable: Move the switch
to position to disable
manual mode.
Manual mode is designed for high traffic doors, when Manual mode is enabled,
the door will be openable without PIN code or key, Manual mode could be disabled
temporary by press and hold any key on keypad for 2 seconds from outside.
Press[1]
Press[2]
1.Modify master PIN code
2.User setting
3.Delete users
5.Language setting
7.Bluetooth setting
8.Function extension
Modify master PIN code
Press[3]
Press[5]
Press[8]
1.Add user PIN code
1.Delete user PIN code
1. Join network
2. Log off network
1.English
2.Spanish
3.Portuguese
4.French
5.Chinese
6.Silent mode
Press[7] 1. Enable Bluetooth
2. Disable Bluetooth

Open & Lock the door
How to use
How to open the door from outside
PIN code Mechanical key
1. Touch keypad
by palm to lighten
keypad.
2. Enter the enrolled
PIN code with end
of [ # ]. Voice prompt
“Verification
Succeeded”.
3. Press down handle
to open the door.
Random security coding function
The random number can be added before or after the real user PIN code but the maximum length is 20 digits.
This feature will pervent the real user PIN code from being exposed.
Key cylinder
1. Insert the key into key hole and rotate it with proper angles.
2. Press down handle to open the door.
How to open the door from inside
Door handle
Press down handle to open the door.

Service features
How to use
Reset to factory default settings
Operation instructions:
1. Keep the lock in “unlock” status.
2. Open battery cover and find the reset button.
3. Use a paper clip to press and hold the reset button.
4. Remove at least 1 pcs battery from battery box, then reinstall all batteries again.
5. Keep holding the reset button until hearing voice guide “Restoring wait a moment”.
Micro USB emergency power supply
Power bank (Micro USB)
Emergency power port
When the battery voltage is too low and cannot be
opened from outside, connect a 5V power supply via
Micro USB port at the front. Then unlock
the door and replace all batteries immediately.
All user data will be deleted!
Reset button

Service features
How to use
Reboot button
Reboot
button
Press the reboot button to restart the lock,
when the system is unresponsive.
No user data is deleted.
Replace batteries
1.5V AA Alkaline Battery is required.
Total is 4 pcs, Do not mix old and
new batteries together in replacement
Network module
Please contact Hafele customer service center for more details.
Access master mode and press [ 8 ] for function extension,
which is reserved for wireless communication and other
smart home interfaces.
Network
module
interface Network module
(optionally available)
IoT

www.hafele.com
Installation guide
Model DL6500
Digital door lock
DL6500
* The contents of this installation guide are subject to change without prior notice
to the user in order to enhance performance of the products.

Product specifications
Outside panel
Key cylinder
Touch keypad
Emergency power port
Reboot button
Inside panel
Battery cover
Reset button
Manual mode switch
Latch lock
Shaft socket

Product specifications
Mechanical key
Handle screw(1 pcs)
Handle screw
(1 pcs)
Outside panel
Cross bolt
Inside panel
Battery cover
Mounting plate
Mounting
screws(3 pcs)
Mounting
screws(2 pcs)
Cover screws(2 pcs)

Preparing for installation
Indoor
Outdoor
Left-in
Outdoor
Indoor
Right-in
Outdoor
Indoor
Left-out
Outdoor
Indoor
Right-out
Check door open direction
This product fits for all door open directions Left-in / Left-out / Right-in / Right-out.

Preparing for installation
Adjust the backset
This latch lock can be adjust the backset from 60 mm to 70 mm by following the below picture.
2-3/8”
(60mm) 2-3/8”
(60mm)
2-3/4”
(70mm) 2-3/4”
(70mm)
Change the faceplate (If necessary)
Check the type of door frame sockets to be installed.
Type 1
Type 2
Follow the 3 steps to complete the faceplate replacement.
No change
necessary

1. Mark and drill bores by using the installation template first, then fix the latch lock into the door frame.
Installation
Type 1
Type 2
Angle
2. Install strike plate onto door jamb.
Jamb
Make sure latch angle face door jamb.
Wood Block (Not included)

Installation
3. Fix cross bolt on the front panel.
4. Pass the connection wire through the top bore.
Then align and insert square shaft into shaft socket
to make the front panel fit against the door closely.
5. Pass the connection wire through the mounting plate and
install the mounting plate with fixing screws tightly against
the door surface.
6. Insert the connecting wires of front panel into the related
sockets of the back panel.
PCB connector
Cable connector

Installation
7. Make the back panel fit against the door closely.
Then tighten fixing screws.
8. Install the batteries and the battery cover.
9. Install the exterior and interior handle, then tighten
the fixing screw.
10. Please check handle and mechanical key for proper operation.
Test if mechanical key works smoothly
after installation.