Hafele Dialock Cylinder DC Operating instructions

Dialock Zylinder DC
Dialock Cylinder DC GB
D
Montage- und Kurzanleitung
Mounting and Brief Operating Instructions

17
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
Contents
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Area of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Conditions for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Instructions for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Brief operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacement of batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Emergency opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
17

18
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
Scope of delivery
• Cylinder with outside and inside knob
• Two 3 volt lithium batteries (art. no. 560-0004-03000) (8)
• Forend (11)
• O-ring (2) for front cover (1)
• Grub screws (7)
• Contact bridge (9)
Optional:
• Instructions for Installation and Operation
with Allen key 2 mm and 0.9 mm
1 Front cover
2 O-ring
3 Knob screw (
Allen screw)
4 Outer knob
5 Connection wire
6 Cylinder
7 Grub screws
8 Batteries
9 Contact bridge
10 Inner knob
11 Forend
12 Mortise lock

19
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
Area of application
The Dialock DC Cylinder is convenient and easy to use and is part of the
Dialock Electronic Locking System. It is an electronic locking cylinder for
indoor installation with mortise locks to DIN 18 251. It is possible to
replace an existing standard locking cylinder with the Dialock DC Cylinder.
Conditions for installation
Important!
To install the Dialock DC Cylinder, use only a cylinder of the correct
inner and outer length (distance A and B). When measuring the cylin-
der lengths, the height of the inner and outer lock rosettes must be
taken into account.
The dimensions A and B are
important when ordering.
A = outer dimension (mm):
distance between the outer
edge of the inner rosette and
the centre of the hole for the
forend.
B = inner dimension (mm):
distance between the outer
edge of the inner rosette and
the centre of the hole for the
forend.
Door panel
Outer edge of
inner rosette Outer edge of
outer rosette
Hole for forend

20
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
Instructions for Installation
Important!
The Dialock DC Cylinder should be installed only by a qualified per-
son. Non-compliance with these instructions may cause serious
damage to the Dialock DC Cylinder.
Do not close the door before carrying out all of the following steps.
Otherwise it will not be possible to open the door from the outside.
Note: The Dialock DC Cylinder is already greased by the manufac-
ture. Further lubrication is not required.
1. Using a suitable tool, release the front cover (1) from the outer knob (4)
and carefully pull it out. The front cover (1) is secured against twisting
by means of a groove..
Important:
Take care not to damage the connection wire (5).
2. Using the Allen key, unscrew the two screws (3) inside the outer knob
(4) and remove the outer knob (4).
Important:
Take care not to damage the connection wire (5).
3. From the inside of the door, push the connection wire (5) through the
lock (12). Push the cylinder (6) into the lock (12) until the forend (11)
can be screwed in from the edge of the door.

21
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
Important:
Check the position of the cylinder (6) before screwing in the forend.
Do not use force. Non-compliance with these instructions may
irreparably damage the cylinder (6) and the lock (12).
4. Tighten the cylinder (6) with the forend (11). Check that the catch turns
smoothly when the inner knob (10) is turned.
5. Push the connection wire (5) through the slot in the outer knob.
6. Push the front cover (4) onto the outside of the cylinder (6) and screw
the two screws (3) hand tight using the Allen key.
Important:
When pushing into position, the outer knob (4) must not be twisted,
otherwise the connection wire (5) may be damaged.
7. Push the O-ring (2) into the groove on the front cover (1).

22
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
8. On the inside of the front cover (1) there is a terminal (A). Push the end
of the connection wire (5) into the terminal (A). When pushing into, the
non-insulated cable side (silvery) must be visible.
Do not use force!
The locking device is open (manu-
facturer's setting)
The connection wire (5) can be ins-
erted.
If the locking is closed, it is not possi-
ble to insert the connecting cable. In
this case, the locking device must first
be pulled carefully out.
A
5
B
1

23
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
12
34
5 6
silvery

24
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
The connecting cable is correctly
inserted and the locking device is
correctly closed.
9. Press the front cover (1) onto the outer knob (4). Important: observe
the correct position of the groove (twist guard). Take care not to kink
or damage the connection wire.
The outer knob is now fully installed.

25
Mounting and Brief Operating Instructions
English
Dialock Cylinder DC - Status: 09.2003 - 732.29.140
10. Insert the batteries provided (8).
Ensure they are inserted correctly!
11. Push the contact bridge (9) into position.
12. Place the inner cover (10) in position and using the Allen key, screw
the three grub screws (7) hand tight.
The inner knob is now fully installed.
13. Function test: press the white button on the panel. The
LED panel flashes green 5 times and then red 5 times
(first use only).