
0. GENERAL WARNINGS
3
* This thermal transmier is an appliance to be fixed to the wall. Please read the explicatory instrucons for its assemblage.
* This transmier has been filled with determined quanty of special thermal fluid. For this reason the necessary reparaons that need the
opening of the deposit or presence of any kind of escape should be undertaken by the manufacturer or by its Technical Assistance Service.
* Never pull the wire. Do not leave the connecon wire in contact with the appliance while it is on.
* During its funconing, one must be careful to maintain the appliance far from combusble material such as curtains, carpets furniture etc.
*
DO NOT COVER THE APPLIANCE. DO NOT USE IT TO DRY CLOTHES. If it is covered there is an overheang risk.
* In order to prevent children from modifying the thermal transmier programming, a safety blocking funcon is incorporated.
* DANGER: If the power supply cable is damaged, it should be substuted by the manufacturer or its Technical Assistance Service, or any
qualify personal.
* If the appliance is going to be installed in the bathroom, it should be put in such a way that nobody in the bathtub or shower should be
able to touch it.
* The appliance should not be located under or in front of a power supply socket.
* In order to disconnect the thermal transmier from the mains power supply, unplug from the wall socket.
* Ensure that the thermal transmier has been unplugged from the wall socket before carrying out any operaon inside.
* At the moment of geng rid of these transmiers, the established rules for their treatment and recycling should be kept into account
(thermal fluid).
* The installaon should be undertaken according to the correct rules regarding the electric installaon.
* The appliance should be installed in such a way that the power supply plug should always be accessible.
* This transmier should not be fied in. Please respect the safety distance.
* The appliance is not intended for use by persons (incluiding children) with reduced physical, sensory or mental capabilies, or lack of
experience and knowledge, unless they have been given supervision or instrucon concerning use of appliance by a person resposible for
their safety. Children should be supervised to ensure that they do not play with appliance.
* The transmier CAN´T work with external programming devices or any other device of exterior control, EXCEPT “Pilot Wire” external devices.
* The smoke from cigarees, candles and incense burners combined with the effect of convecon can cause stains on the wall. This is not a
failure the apparatus. Furthermore, the effect of sunlight or halogen may cause some discolouraon in the apparatus.
* Temperature variaons in the immediate environment of the device can generate "noise" and "clicks". Not a fault of the device.
* The guarantee of the appliance will not cover any damage caused by not reading and following carefully these instrucons.
1.1. KEYBOARD AND LCD DISPLAY
0.0. SAFETY WARNINGS
1. HEATER DESCRIPTION
* Install the device in observance of all the laws, rules and regulaons in force in the countries where installaon takes place.
* II devices may have a black wire from the remote control pilot wire. If this wire is not used, it must be insulated and for no reason
earthed.
*The appliance should not be located under or in front of a power supply socket.
* Always disconnect the electricity supply from the mains before any maintenance operaons.
* Check that the electricity supply system is connected through a Magnetothermic Circuit Breaker and a high sensivity Residual Current Circuit
Breaker connected directly to the socket or connecon box in use. A circuit breaker switch dedicated exclusively to the appliance is obligatory.
All contacts must be separated by a distance of at least 3 mm.
RCB has four buons and a display. ON/Stand-by buon switches the regulator ON or puts it on standby: when RCB is on standby, the display
shows a flashing wring “St by” while when it is ON the display shows me and program in the chrono mode, the number of the integrated
program selected (P1,P2,P3) or the temperature seng in the other modes.
The BUZZER emits one beep aer the transion from STAND-BY mode to ON state. The beep duraon is 1 second.
Viceversa aer the transion from ON state to the STAND-BY one, the BUZZER emits two short beeps (0,5 s every one with a break of 0,5s between).
Also when the RCB is power-up, the buzzer behavior will be according the rule above.
On the display side there is a three zone color silk-print bar and an arrow symbol on the display indicates one of these colors depending
on the seng temperature value. This is an visual indicaon that higher temperature sengs imply higher energy consumpon.
Buon -
Buon +
Buon ON/Standby
Display
Mode icon
Thermometer symbol
Behavioral indicator