Hayward Turbo Cell User manual

T-CELL-15
GLX-CELL-15-W
NEW MENU SETTING MAY BE REQUIRED!
The T-CELL-15 and GLX-CELL-15-W are designed for pools up to 40,000 gallons. When
replacing an existing T-CELL-15 orGLX-CELL-15, no re-configuration isneccessary.
ConfigurationofyourcontrollermayberequiredbeforeusingtheT-CELL-15orGLX-CELL-15-W
chlorinator cell. Refer to the information below. Incorrect configuration will cause inaccurate salt
readings,improperoperation,andpossiblesystemshutdown.
CONFIGURATIONisnecessarywiththe followingmodels:
• AQR(AquaRite- all 2009orlater)-firmwareversion 1.5orlater
• AQR-PRO(AquaRitePro)
• PL-P-4(ProLogicP4)
• PL-PS-x(ProLogicPS)
• AQ-LOGIC-P-4(ProLogicP4)
• AQ-LOGIC-PS-x(Pro LogicPS)
NOCONFIGURATIONisneccessarywiththefollowing models:
• AQ-RITE(AquaRite -2008andearlier)- firmwareearlierthanversion 1.5
• AQ-RITE-XL(AquaRiteXL)
ConnectingtoanAQR:
1. SlidetheMainSwitchtothe"Auto"position.
2. PushtheDiagnosticbuttonrepeatedlyuntil"t-xx" appearsonthedisplay("t-15"isthefactory
default).If“t-15”isdisplayed,skipto step 4.
3. Tochangecelltype, slidetheMainSwitch from"Auto"to"Super Chlorinate"andbackto "Auto".
Repeatthisprocessuntilthe“t-15”isdisplayed.
4. PushtheDiagnosticbuttontoexit.
ConnectingtoanAQR-PRO:
1. AccesstheSettingsMenubypushingthe“Settings”button.
2. Push“>”untilChlor. Configisdisplayed,thenpush“+”.
3. Push“>”repeatedly until“CellType”isdisplayed.
4. Push “+” or “-” until “T-CELL-15”isdisplayed.
5. ExitSettingsMenubypushingthe “Info”button.
ConnectingtoanAQ-LOGIC-P-4,AQ-LOGIC-PS-x, PL-P-4or PL-PS-x:
1. EntertheConfigurationMenu.
2. Push“>”untilChlor. Configisdisplayed,thenpush“+”.
3. WiththeChlorinatorEnabled,push“>”repeatedlyuntil“CellType” isdisplayed.
4. Push “+” or “-” until “T-CELL-15”isdisplayed.
5. ExitSettingsMenubypushingthe“Menu”button.

IMPORTANTINFORMATION
Regarding Extended Pool Filtration cycles, and Low Flow Rate conditions
THEAMOUNTOFCHLORINE PRODUCED BYYOURHAYWARD/GOLDLINESALTCHLORINE
GENERATINGSYSTEMISDEPENDENTONTHELENGTHOFTIMETHATYOURFILTERPUMP
RUNSEVERYDAY. SO,YOURCHLORINATIONSETTINGSHOULDBEMATCHEDTOTHEFILTER
PUMPRUNTIMEOFYOURPOOL.
WhetheryouplantoINCREASEorDECREASEthefilterpumpcycleonyourpool,adjust the chlorination setting using
thedialonyourAquaRite,ortheupanddownkeysonyourAquaRitePro,AquaLogicorProLogicsystem.Byproperly
adjustingyour setting,youarepreventingthe over-chlorinationorunder-chlorinationofyourpool.
Forexample,If you planondoubling the filterpumpoperating time (sayfrom8 hours/day to16hours/day), then reduce
yourchlorination setting by afactorof2(sayfrom50%to25%). Ifyouplan to triple yourfilterpumpoperatingtime,then
reduceyourchlorinationsettingbyafactorof3.Likewise,ifyoureduceyourfilterpumpoperatingtime(sayfrom12hours/
dayto8 hours/day), thenincreaseyour chlorination settingby a factor of1.5 (i.e. 12/8=1.5)
Theseadjustments,whilenecessaryandimportant,areAPPROXIMATIONS to the actual adjustment your pool requires.
Afterany chlorinationadjustment,monitorthepool’s chlorinelevelcloselyfor1-2weeks.If thereadingsstabilizeinthe1-
3 ppm range then you are all set—otherwise make another small adjustment (up or down) to increase or decrease the
chlorinelevel. Once thechlorinator isset, it is good practiceto check your chlorine levelsweekly to ensure operation is
normal.
WHENUSING 2 SPEED ORVARIABLE SPEED PUMPS ON LOWSPEED, CHECKTO BE SUREYOUR SALT
CELLIS RECEIVINGADEQUATE FLOW. Low flow conditions can result in insufficient water in the cell causing
inefficientchlorineproduction.Asaprecaution,thecellcanbeinstalledvertically orinaninvertedmanner(seeillustration)
tokeep it flooded with water.
V
ertical Installation Inverted Installation
Desired installation configurations when using 2 speed or variable speed pumps.
092409A RevB