Heitronic 27004 User manual

H. Vollmer GmbH
Installation instructions article no.: 27004-27007 Page 1 of 3 From 08.03.2016
GB Installation and operating
instructions LED Wall & Ceiling Light
Art. no. 27004-27007
These operating instructions are only intended for the products listed above.
They contain important information about starting-up and operating the light.
Take note of these operating instructions also when transferring the product to a third party.
For this reason it is important to keep these instructions in a safe place for later reference.
1. Introduction
Dear Customer, thank you for choosing to purchase our product.
You have purchased a product from the House of Vollmer, which has been constructed according to today's
state-of-the-art technology.
The light satisfies all the requirements of applicable European and national guidelines.
In order to maintain the condition of the product and ensure safe operation, as the user you must observe
these operating instructions!
2. Safety notes
The warranty does not cover damages caused by failure to comply
with these operating instructions!
We do not assume any liability for any damages caused by incorrect usage!
Usage of the light is strictly prohibited if the light has been damaged.
Do not leave children unattended in the area of the light or other electric devices.
During operation the LEDs are hot. The outer casing of the lights also becomes hot. Do not touch the
light with bare hands while in operation.
Do not bring the light in contact with extreme heat or open flame.
The entire product cannot be modified or rebuilt. The warranty expires if modifications are made to the
light.
The serial plate cannot be removed.
3. Intended usage
The light is designed for indoor/outdoor usage.
This product is only intended for lighting purposes and:
can only be operated with voltage of 230V~50Hz.
can only be connected according to Protection Class II (two).
can only be operated when firmly mounted on a stable, level and tip-proof surface.
can only be operated on normal and/or non-flammable areas.
cannot be exposed to strong mechanical stress or heavy soiling.
Heitronic
®
H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach Stein

H. Vollmer GmbH
Installation instructions article no.: 27004-27007 Page 2 of 3 From 08.03.2016
4. Before installation/start-up
The light can only be operated outside of the packaging.
Carefully remove the light from the packaging.
Before starting up the light ensure that it has not been damaged during transport. The light cannot be
operated if the electrical components are damaged. Repairs can only be carried out by a certified
electrician.
Keep packaging material away from children and pets. Risk of suffocation!
5. Installation/start-up
This product can only be installed by a qualified electrician.
Before installation the connection cables in the building must be disconnected from voltage and
secured from being switched back on. Activate the corresponding circuit breakers in the building's
wiring system.
Ensure that the surface is able to carry the weight of the light reliably on a sustained basis.
Hold the light housing at the desired installation position and mark the drill holes. Use appropriate
screws to mount the light. Ensure that no wires are damaged.
Now connect the connection cables of the building's wiring system to the light's screw terminals. As a general
rule the brown (or black) cable is the phase conductor: connect it to the terminal marked "L". The blue
conductor must be connected to the terminal labelled "N".
Do not bend the cable; please ensure that the cable and connector are free of tractive force and torque.
Protect all cables and insulation from potential damage.
Check once again to ensure that everything is connected properly.
Turn the circuit breakers in the building's wiring system back on.
6. Installation information
7. Malfunctions
The light does not turn on
Is the light switched on via the wall switch?
Check the connected wires
Heitronic
®
H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach Stein

H. Vollmer GmbH
Installation instructions article no.: 27004-27007 Page 3 of 3 From 08.03.2016
8. Technical data
Article Connection LED light Protection
type
Protection
class
Frequenc
y/countrie
s
27004 230 V ~ AC,
50 ~ 60 Hz
Ø ca. 200 mm, 12W, 960lm, 3000K IP 44 II -
27005 230 V ~ AC,
50 ~ 60 Hz
Ø ca. 300 mm, 25W, 1900lm,
3000K IP 44 II -
27006 230 V ~ AC,
50 ~ 60 Hz
Ø ca. 200 mm, 12W, 960lm,
3000K, day & night sensor, motion
detector
IP 44 II
5,8 GHz/
D,GB,F,N
L
27007 230 V ~ AC,
50 ~ 60 Hz
ca. 300x300 mm, 25W, 1900lm,
3000K IP 44 II -
9. Care instructions
Disconnect the entire product from voltage and let it cool down before performing any cleaning or
maintenance measures on the product.
Clean the product regularly - only use a slightly moist, soft and lint-free cloth. Observe the enclosed
instructions as necessary.
10. Disposal
Waste electronic equipment must be taken to the public collection point and cannot be disposed of as
household waste.
Heitronic
®
H. Vollmer GmbH
Allmendring 29
D-75203 Königsbach Stein
27004,27005,27006
27007