Heitronic 27794 User manual

1 of 3 | Dated 26.02.2016
GB Installation and Operating Instructions
LED panel
Art. No. 27794,27795,27796
These operating instructions refer exclusively to the above products.
They contain important information for the start-up and handling of the light.
Therefore, follow these operating instructions, even if you pass this product onto a third party.
It is important, therefore, that these instructions are archived carefully for referring to information at a
later stage.
1. Introduction
Dear customer, thank you for deciding to purchase our product.
You have acquired a product from Vollmer, which has been built according to the current state of technology.
The light fulfils the requirements of effective European and national guidelines
To maintain the condition of the product and to ensure safe operation, you - as the user - must observe the
instructions of this operation manual!
2. Safety Instructions
The guarantee becomes invalid if damage occurs due to the failure of following these operating
instructions!
We do not accept liability for any consequential damage!
Commissioning is strictly prohibited if there are any damages to the light.
Do not allow children to play unsupervised near the light.
Do not allow the light to come into contact with extreme heat or naked flames.
The product in its entirety must not be altered or modified. Alterations to the light invalidate the
guarantee.
The type plate must not be removed.
3. Proper Use
The light is designed for use in outdoor/indoor areas.
This product is only intended for lighting purposes and may:
only be operated with a voltage of 230V ~50Hz
only be connected according to protection class II (two)
only be operated when mounted to a sturdy, level and non-tilting surface
only be operated on normal or non-flammable surfaces
not be subjected to strong mechanical loads or heavy soiling.
4. Before Installation/Commissioning
The light may only be operated once removed from the packaging.
Remove the light from the packaging carefully.
Make sure that the light has not been damaged during transport before taking it into operation. The light
may not be operated if there are any damages to electrical parts. Repairs may only be carried out by a
qualified electrician.
Keep packaging materials away from children and pets. Asphyxiation hazard!

2 of 3 | 26.02.2016
5. Installation/Commissioning
This product can only be installed by a qualified electrician.
The connection lines in the building must be disconnected before installation and secured against being
switched back on. For this, trip the corresponding fuse switch in the building installation.
Make sure that the surface is suitable for permanently and reliably taking the weight of the light.
Using a saw, cut out the installation dimensions at the desired position. Use the retainer clips to mount
the LED panel. Make sure that no lines are damaged.
Now connect the building installation's connection lines to the screw terminals on the transformer The
brown (or black) cable is generally the phase conductor - connect this to the terminal marked with "L".
The blue conductor must be connected to the terminal marked with "N".
Do not bend the cables; make sure that the cables are not subject to tension or torsional forces. Protect
all cables and insulation against possible damages.
Check proper connection once again.
Switch the building installation's fuse switch back on.
6. Faulty Function
Light does not switch on
Light switched on at the wall switch?
Transformer mounted and connected properly?
Check the connected lines
7. Technical Data
Article Connection Installation
dimensions LED panel
Protec-
tion
Type
Protec-
tion
Class
27794
AC 230V ,
DC max. , 24-38V,max
40V, 350mA
180 x 180mm 14W, 730lm, 3000-6000K,
dimmable IP20 II
27795
AC 230V ,
DC max. , 24-38V,max
40V, 350mA
Ø187mm 14W, 900lm, 3000-6000K,
dimmable IP20 II
27796
AC 230V ,
DC max. , 24-40V,
max.45V, 450mA
273 x 273mm 17W, 1400lm, 3000-6000K,
dimmable IP20 II
8. Setting the light
You can set 3 different lighting situations (warm white, cold white and daylight white) by switching your
light switch on and off (the light must remain switched off for at least two seconds).
The lamp has a memory function so that the lighting situation that you last set will automatically occur
when you next activate the lamp. (However, the light must remain switched off for at least 10 seconds)
9. Care
Disconnect the entire product from the mains first before cleaning or maintaining the product.

3 of 3 | 26.02.2016
10. Waste Disposal
Old electronic devices must be taken to public waste disposal sites and must not be put into general
household waste.