Henny Penny BW-200 User manual

OPERATOR’S
MANUAL
ELECTRIC PASS-THRU BUN WARMER
MODEL
BW-200
REGISTER WARRANTY ONLINE AT WWW.HENNYPENNY.COM
Read instructions before operating the appliance

i
Sept. 2013
TABLE OF CONTENTS
Section Page
Section 1. INTRODUCTION.................................................................................................... 1-1
1-1. Safety ............................................................................................................... 1-1
Section 2. INSTALLATION...................................................................................................... 2-1
2-1. Installation........................................................................................................ 2-1
2-2. Unpacking........................................................................................................ 2-1
2-3. Cabinent Dimensions....................................................................................... 2-2
Section 3. OPERATION ............................................................................................................ 3-1
3-1. Operating Components ................................................................................... 3-1
3-2. Cleaning Instructions ....................................................................................... 3-1
Section 4. PROGRAMMING.................................................................................................... 3-1
4-1. Special Programming ...................................................................................... 3-1
4-2. Cleaning Instructions ....................................................................................... 3-1
Section 5. TROUBLESHOOTING........................................................................................... 5-1
5-1. Error Codes ...................................................................................................... 5-1

2
Sept. 2013
1-1
SAFETY
The instructions in this manual have been prepared to aid you in learning
the proper procedures for your equipment. Where information is of
particular importance or is safety related, the words NOTICE, CAUTION,
or WARNING are used. Their usage is described below.
If a problem occurs during the first operation of a new unit, recheck the
Installation Section of the Operator’s Manual.
Before troubleshooting, always recheck the Operation
Section of the Operator’s Manual.
Where information is of particular importance or is safety related, the
words DANGER, WARNING, CAUTION, or NOTICE are used. Their
usage is described as follows:
SAFETY ALERT SYMBOL is used with DANGER, WARNING
or CAUTION which indicates a personal injury type hazard.
NOTICE is used to highlight especially important information.
CAUTION used without the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, may result
in property damage.
CAUTION used with the safety alert symbol indicates a
potentially hazardous situation which, if not avoided, could result
in minor or moderate injury.
WARNING indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
DANGER INDICATES AN IMMINENTLY HAZARDOUS
SITUATIONWHICH,IFNOTAVOIDED,WILLRESULTIN
DEATH OR SERIOUS INJURY.
SECTION1:INTRODUCTION
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory, or mental capabilities, or
lack of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety

3
Sept. 2013
SECTION 2: INSTALLATION
The bun warmer is available from the factory as a 120 VAC unit.
The data plate, located on the rear of the module, will specify
the correct electrical supply. The unit requires a grounded
receptacle with a separate electrical line protected by a fuse or
circuit breaker of the proper rating. If the unit is connected to
electrical supply with a plug and receptacle, the plug must be in
an accessible location, or the unit must be hard wired.
This unit must be adequately and safely grounded.
Refer to local electrical codes for correct grounding
procedures. If fryer is not adequately grounded,
electrical shock could result.
2-1.
INSTALLATION
Do not puncture the unit with any objects such as
drills or screws as electrical shock or component
damage could result.
Installation of this unit should be performed only by a
qualied service technician.
The Henny Penny Bun Warmer has been tested, inspected, and
expertly packed to ensure arrival at its destination in the best
possible condition. The cabinet rests on cardboard pads that
sit on a wooden skid. The unit is then packed inside a heavy
cardboard carton with sufficient padding to withstand normal
shipping treatment.
To remove the Henny Penny Bun Warmer from the carton, you
should:
1. Carefully cut banding straps.
2. Lift the carton off the unit.
3. Lift the unit off the cardboard padding and skid.
4. Peel off any protective covering from the exterior of the cabinet.
5. The unit is now ready for location and set up.
Any shipping damage should be noted in the presence
of the delivery agent and signed prior to his or her
departure.
2-2.
UNPACKING
Model Volts Amps Watts
BW-200 120 5.5 650
BW-200 230 550 2.4

4
Jan. 2014
2-3.
CABINET
DIMENSIONS
BW-200
Front/Back
BW-200
Side
Product Weight (lbs)
BW-200 100

5
Sept. 2013
SECTION 3: OPERATION
3-1.
OPERATING
COMPONENTS
3-2.
CLEANING
INSTRUCTIONS
1. Turn power switch to the ON position.
2. After a sequence of codes the display shows the time of day,
or “ON”.
Temperature Setpoint Programming
1. Press and hold the TEMP button for 6 seconds. The actual
temperature shows first followed by the flashing setpoint
temperature.
2. While holding in on the TEMP button, press and release the
SET button. Now the setpoint temperature blinks at a faster
rate. Now release the TEMP button.
3. Press the UP and DOWN buttons to change the setpoint
temperature.
4. Once the desired setpoint temperature (preprogrammed
maximum temperature) is reached, press the SET button
toreturn to normal operation mode and the setpoint is saved.
“Time of Day” Programming
Press and hold the SET button while using the UP and DO
buttons to set the desired time. When the SET button is released,
the time is saved.
Press and hold the TEMP button to view the actual
temperature of the unit.
Due to the lower temperature settings, this unit
has been designed to hold NON-POTENTIALLY
HAZARDOUS FOOD ONLY. This unit will NOT
hold potentially hazardous food at a safe temperature
To avoid burns, allow the unit to cool
before cleaning.
1. Turn the unit to the OFF position.
2. Disconnect electrical supply to the unit.
3. Open doors and wipe down racks.
4. Clean doors with a non-abrasive, soft cloth and mild soap.
Do not use ammonia.
5. Clean the interior and exterior of the unit with a soft cloth,
soap, and water.
Do not use steel wool, other abrasive cleaners or cleaners/sanitizers
containing chlorine, bromine, iodine or ammonia chemicals, as these will
deteriorate the stainless steel material and shorten the life of the unit.
Do not spray the unit with water, such as with a garden hose. Failure to
follow this caution could cause component failure.

6
Sept. 2013
SECTION 4: PROGRAMMING
4-1.
SPECIAL
PROGRAMMING
1. With POWER switch off, press and hold both the UP and
DOWN buttons, and then turn the POWER switch on until
“SP”shows on the display. Release the UP and DOWN
buttons, and “oF” or “oC” shows on the display.
2. Press the UP or DOWN buttons to toggle from “oF” to “oC”,
or “oC” (Celsius) to “oF” (Fahrenheit).
3. Press the SET button, and “CAL” shows in the display. Press
and hold TEMP button, and press the UP and DOWN buttons
to match the display with the actual temperature.
4. Press the SET button, and “CPU” shows in the display.
Press and hold TEMP button to view the CPU (control PCB)
temperature.
5. Press the SET button, and “OutPutS” shows in the display.
Press the TEMP button to turn the relays, display and heaters,
OFF and ON.
6. Press the SET button, and “In-” shows in the display. Press
and hold either the UP or DOWN button until “In- SYS”
shows in the display. This programs factory settings back
into the controls.
7. Press the SET button. If “C=y” shows in the display, the
time of day shows in the display during normal operation.
If “C=n” shows in the display, “ON” shows in the display
during normal operation. Press the UP and DOWN buttons
to toggle from one to the other.

7
Sept. 2013
DISPLAY CAUSE PANEL BOARD CORRECTION
“E-4” Control board overheating
Turn POWER switch to OFF then back ON; if
display still shows “E-4”, the unit is overheating or
louvers are clogged
“E-6” Faulty temperature temperature
probe Check probe for loose connection or probe faulty
“E-41” Memory scrambled
Press and hold the UP and DOWN buttons and turn
unit on. Aer SP shows on display, press SET button
twice. en press and hold the UP or DOWN button
until In-SYS shows in display; if “E-41” persists,
replace the control board
“Hi” Unit overheating; faulty relay or
control board Have relay or control board replaced
5-1.
ERROR CODES
SECTION 5: TROUBLESHOOTING
More detailed troubleshooting information is available in the Technical Manual, available at www.
hennypenny.com, or 1-800-417-8405 or 1-937-456-8405.

Henny Penny Corporation
P.O.Box 60
Eaton,OH 45320
1-937-456-8400
1-937-456-8402 Fax
Toll free in USA
1-800-417-8417
1-800-417-8434 Fax
www.hennypenny.com
*FM05-092-A* Henny Penny Corp., Eaton, Ohio 45320, Revised 10-09-13