Herman Miller Aeron User manual

Read this
while
adjusting
your
Aeron
®
chair

Instructions on this card show all
possible adjustments. Specific adjustments
vary according to chair model.
To view theAeron chair user-adjustment video,
visit www.HermanMiller.com

Seat Height
Paddle-shaped lever on right side
To raise: While taking your weight off chair,
lift lever up.
To lower: While seated, lift lever up.
Adjust chair height so your feet rest flat on the
floor or footrest, with your body comfortably
supported by breathable Pellicle®suspension.
Avoid dangling legs, which puts pressure on
the back of thighs and restricts blood flow.A
work surface or keyboard that seems too high
or low may require adjusting.
Kinemat
®
Tilt Tension
Long stem on right side with knob
To increase tension: While seated, turn knob
forward (clockwise, toward + sign).
To decrease tension: While seated, turn knob
backward (counterclockwise, toward – sign).
Depending on the desired tilt resistance, a
number of turns may be required.
Increased tilt tension provides more stability
and back support while you recline. Too much
resistance may make it difficult to recline.
Depending on weight and preference,
different people will require different levels
of tilt resistance.
-+
Tilt Tension
Seat Height

Arm Height
Lever on base of arm support
To raise or lower arm: While seated, lift lever
to unlock. Grasp base of arm support and raise
or lower to desired height. Lower lever to lock.
Adjust height of each chair arm so your
arms are supported. This helps take weight
off your shoulders.
ArmAngle
Front of each armpad
To swing arms in or out: While seated,
grasp front end of armpad and pivot it to the
left or right.
Adjusting arm angle can help support
different types of work and shifts in posture.
Swing chair arms inward for support while
using keyboard. Swing arm out to support
use of computer mouse.

Forward Tilt
Front lever on left side
To position chair forward: Lean back and lift
lever all the way up. Lean forward.
To resume horizontal position: While seated,
push lever all the way down. Lean back.
Normally, forward tilt position is used with
increased chair height. This relaxes the
bend of your waist, knees, and ankles. To
support back, set tilt limiter after assuming
forward position.
Tilt Limiter
Rear lever on left side
To limit tilt range: Recline as far as you
like. Move lever up to define the limit of
recline.You can still move forward.
Readjust as necessary.
To release tilt limiter: Lean forward,
press lever down.
If you want to sit in an upright position,
set the tilt limiter when the seat is in a
horizontal or forward position.
Forward Tilt
Tilt Limiter

Lumbar Depth
Thick pad on back of chair
To adjust depth: Using equal pressure on each
end of lumbar support pad, lift it out of its
track in back of chair. Flip it over and replace
in track. (Notice that one side of support pad
is thicker than the other side.)
Switch between thick and thin sides of the
pad so that it comfortably supports the natural
curve of your spine.
Lumbar Height
Thick pad on back of chair
To change height: Using equal pressure on
each end of lumbar support pad, raise or lower
it to desired position within adjustment track.
Adjust pad height so that it comfortably
supports the natural curve of your spine.

PostureFit
®
Adjustment
Knob on right side of chair
To engage: While seated, turn knob forward
(clockwise) until it stops. Then turn knob
backward (counterclockwise) until you find
the support that feels right for you.
To disengage: While seated, turn knob
backward (counterclockwise).
Note: Set PostureFit with tilt limiter engaged in
forward position to achieve the best fit for you.
Before making this adjustment you should
be seated with your back in the pocket of the
chair back. Then adjust PostureFit so that it
comfortably supports the natural alignment
of your spine and provides lower back comfort.
-+
Fine-Tune™Footring Height
Long stem on left side with knob
To raise: While seated, lift your feet off the
footring, turn knob forward.
To lower: While seated, lift your feet off the
footring, turn knob backward.
Adjust footring height so your feet rest flat
on the footring, with your body comfortably
supported by breathable Pellicle suspension.
Avoid dangling legs, which puts pressure on
the back of thighs and restricts blood flow.

User
information:
Installers
do not remove
© 2007 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 169633-J O.AE6202
®l
, Aeron, Kinemat, Pellicle, and PostureFit are among the registered trademarks of Herman Miller, Inc.
™ Fine-Tune is among the trademarks of Herman Miller, Inc.
Users: Retain This Information forFuture Reference
Maintenance
Aperiodic inspection of chair components and fasteners should be made to ensure that
the chair is structurally intact and functioning properly. Damaged and broken parts should
be replaced and loose fasteners tightened.
For more information about our products and services or to see a list of dealers, please
visit us at www.HermanMiller.com or call [phone].