Herman Miller Canvas Office Landscape FT420 User manual

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
1
YCanvas Office Landscape®Shelf and Flipper Unit Installation
and Disassembly for Recycling Instructions
Products Included:
FT420 B-Style Overhead
B-Style - End Panels - Full Hgt
E-Style - End Panels - Full Hgt
E-Style - End Panels - Half Hgt
#2 Phillips Screw Driver
B-Style - End Panels - Half Hgt
FT430 E-Style Overhead
A
C
D
B
Parts Included:
Tools Required:
B-Style Shelf
E
Safety Glass
E-Style Shelf
F
8-32 x 3/8 lg
Pan Head Screw with Serrated
Washer (E-Style Veneer only)
G
IMPORTANT: Save these instructions for layout changes.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
2
E-Style Overhead Door Assy
I
1. If installing Flipper Door Unit under another
Flipper Unit or Shelf, allow 1 1/2” vertical clearance
between products for ipper door movement.
Tighten all screws. Failure to do so may cause product damage
or personal injury or both.
1. End Panel Installation
!WARNING
Anti-Dislodgement Clip
Prior to installation, rotate Anti-Dislodgement clip into position
shown. Note that this may require a rotation of about 180
degrees from the position that the clips are shipped in.
Failure to rotate clip will not allow product to be installed.
!WARNING
B-Style Overhead Door Assy
H
Anti-Dislodgement
Clip fully seated
2. Insert hanger clips into hanger frame slots
making sure Anti-Dislodgement clip is oriented
as shown.
3. Rotate Anti-Dislodgement clip until it ts into
slot and hanger clip is fully seated in hanger
frame. Lift up on the end panel to verify that it is
engaged properly.
4. Repeat for opposite end panel at equal
height.
5. To remove End Panels, reverse steps 2 & 3.
A at bladed screwdriver may be used to
disengage Anti-Dislodgement clip from hanger
frame.

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
3
2. Shelf Installation
For E-Style Veneer Flipper Doors and Flipper Units, replace
existing shelf mounting screws with provided sems screws (screw
with built in serrated washer). Failure to comply may allow shelf to
fall causing damage and/or personal injury.
!
1. Install shelf (E) or (F) onto End Panels by
engaging vertical slots in shelf over mounting
screws (G) or Sems screw (H) for E-style Veneer
Flippers or Flipper units.
2. Make sure Shelf is fully seated on mounting
screws.
3. Tighten all shelf mounting.
SEMS screws
Mounting
screws
For All other Flipper Doors and Flipper Units
For E-Style Veneer Flipper Doors and
Flipper units
Shelf
!WARNING
G
G

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
4
3. Flipper Door Unit Installation
1. With Door/Cover Assembly in open position,
place rear slots in door guides over rear mounting
screws.
2. Slide Door/Cover Assembly back until front slots
in Door Glides drop over front mounting screws.
3. Make sure Door/Cover Assembly is fully seated
onto mounting screws. Tighten all screws.
If this product is recongured or moved, the above steps should be
reversed. A fully assembled ipper unit should never be removed from
the frame or damage to the gear rod assembly will occur.
NOTICE
G
G

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
5
4. Flipper Door Lock Installation
When keyed alike lock plugs are to be installed, install
lock plug into shell in unlocked position (key teeth
pointing down). Install lock plug completely until ush
with lock shell ange to engage lock plug cam.
NOTICE
Lock Shell Flange
Lock Plug Cam
Lock Plug
Key teeth
pointing down Lock Shell Flange

Z
© 2013 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y, Zand Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1b2lw1 rev E.
6
Disassembly and Recycling:
Materials Identication and Segregation:
Where possible, plastic components are marked with ASTM recycling codes. Use
these codes to identify material type for recycling. Non marked components should
be treated as mixed plastic. Ferrous metals can be identied using a small magnet
for recycling. Non-ferrous metals should be separated and recycled separately.
To disassemble product, reverse the above installation steps.