Herman Miller Motia Sit-to-Stand Tables Guide

Once you hear two clicks, release
the buttons.
z Motia Sit-to-Stand Tables Adjustment Guide
1
z
Motia™Sit-to-Stand Tables
Y
Simple Touch Switch Adjustment Guide
How to adjust the height of the table
How to clear a lower or upper height limit How to calibrate the table
Calibrate at installation so legs are in sync or if legs become out of sync
during operation.
Press and hold the up arrow to
raise the table.
Raise or lower the table to one
of the saved height limits.
Adjust the table to the lowest height.
Once you hear one click,
release the buttons.
The table will begin to readjust itself
if necessary. Release the button once
the table has stopped moving and
clicking. Listen carefully; the clicks
are quiet.
Press and hold the down arrow
to lower the table.
Press and hold the up and down
arrows at the same time until you
hear one click (– seconds).
Press the down arrow again and
hold for – seconds.
How to save a lower and upper height limit
Raise or lower the table to
desired height.
Press and hold the up and down
arrows at the same time until you hear
two quiet clicks (– seconds).

z Motia Sit-to-Stand Tables
z
Motia Sit-to-Stand Tables
Y
Adjustment Guide
How to clear a lower or upper height limit
Raise or lower the table to one
of the saved height limits.
Press and hold the up and down
arrows at the same time until you
hear one click (– seconds).
How to save a preferred sitting or standing height
Memory position keys are the numbers on the control. You can save up to four
height settings, one per memory position key.
Adjust the height of the table to the
preferred seated or standing height.
The display will show the current
height of the table in inches.
How to adjust the height of the table
Press and hold the up arrow to
raise the table.
Press and hold the down arrow
to lower the table.
How to save a lower and upper height limit
Raise or lower the table to
desired height.
Press and hold the up and down
arrows at the same time until you hear
two quiet clicks (– seconds).
2
Programmable Control Adjustment Guide
Press the “S” memory key to save
that height as a setting.
Once you hear one click,
release the buttons.
The display will now read “S –”.
Once you hear two clicks,
release the buttons.

z Motia Sit-to-Stand Tables Adjustment Guide
3
How to overwrite a memory position key
Follow all the steps in “How to save a
preferred sitting or standing height.”
Completing the h step will overwrite
the height position that was originally
saved on the memory position key.
How to save a preferred sitting or standing height (continued)
Immediately press a memory position key
to assign a number to the setting.
The display will now read “S ”.
How to calibrate the table
Calibrate at installation so legs are in sync, if legs become out of sync during
operation, or if the digital display doesn't align with actual height.
Adjust the table to the lowest height.
Press the down arrow again and
hold for – seconds.
How to adjust the table to a saved memory key
To cue the table to adjust to a
preferred setting, press and hold
the memory position key that you
assigned to it until the table stops
adjusting. If you release the key
before the table reaches the saved
height, the table will stop adjusting
itself to the saved height.
The table will begin to readjust itself if
necessary. Release the button once the
table has stopped moving and clicking.
You will hear a quiet double click sound,
which indicates that the preferred height
has been saved to the selected memory
position key.
How to hard reset the programmable control (continued)
Press and hold buttons , , and
the up arrow at the same time
until the display reads “S ”.
The display will now read “E”.
Click the up arrow until the display
reads “S ”.
Press the down arrow again and
hold for – seconds.
Once the display reads “S ”,
release the buttons.
Adjust the table to the lowest height.
Press the “S” button. You will
hear the control box click.
The table will begin to readjust itself if
necessary. Release the button once the
table has stopped moving and clicking.
How to hard reset the programmable control
If the table is not responding when you press an arrow key or a memory key, it
may need to be reset.