HIK VISION DS-K1100 Series User manual

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by RS-485
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
1 of 4
DS-K1100 Series Card Readers Connect to DS-K2600
Series Access Controllers by RS-485
Preparation
Connect card reader to access controller is mainly applied to swiping card to open the door for entrring or
exiting. The models of card reader and access controller in this guide are as below:
Card Reader
Access Controller
DS-K1101M/MK, DS-K1102M/MK,
DS-K1103M/MK, DS-K1104M/MK,
DS-K1107M/MK, DS-K1108M/MK
DS-K2601,
DS-K2602,
DS-K2604
DS-K1102E/EK, DS-K1107E/EK,
DS-K1108E/EK
Notice
1. Please cut off power supply before wiring;
2. DS-K1100 Series Card Readers support private RS485 protocol; the details about RS-485 about of
card reader are as below:
Color
Description
Red
Power (DC +12V)
Black
GND
Yellow
RS-485+
Blue
RS-485-
Green
W0 (available for Wiegand Protocol)
White
W1 (available for Wiegand Protocol)
Purple
Beep Control (available for Wiegand Protocol)
Brown
Blue/Green LED Control (available for Wiegand Protocol)
Orange
Red LED Control (available for Wiegand Protocol)
Gray
Tamper (available for Wiegand Protocol)
3. Correspondingly, there are RS485 interfaces in DS-K2600 series access controllers; you can find RS-
485 interface at the same position in DS-K2601/02/04 access controllers, as pictures show:

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by RS-485
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
2 of 4
4. Please check the rear panel of card reader and unscrew it, you could find DIP switch module;
The No. of DIP switch from left to right is 1~8:
Description of DIP Switch:
Icon
Description
Represent 1 in binary mode
Represent 0 in binary mode
No.
Description
DIP Switch Status
1~4
Address of RS485
1: 1
0: 0
5
Read card No. or file in card(Reserved)
1: read file in card
0: read card No.
6
Wiegand protocol or RS-485 protocol
1: Wiegand protocol
0: RS-485 protocol.
7
Wiegand Protocol
(available when No. 6 is 1)
1: Wiegand protocol of 26-bit;
0: Wiegand protocol of 34-bit.
8
Matched Resistance(Reserved)
(available for RS-485 protocol)
1: Enable;
0: Disable.
Step 1: DIP Switch
Please set the DIP switch firstly before connecting the card reader, more details about the binary value of
the card reader by setting DIP Switch to correspond with the door, please check the table below:
DIP Switch Status
Door
Reader
1000 0000
Door 1
Entrance Reader 1
0100 0000
Eixt Reader 2
1100 0000
Door 2
Entrance Reader 3
0010 0000
Eixt Reader 4
1010 0000
Door 3
Entrance Reader 5
0110 0000
Eixt Reader 6
1110 0000
Door 4
Entrance Reader 7
0001 0000
Eixt Reader 8

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by RS-485
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
3 of 4
For example, if you want to swipe card to open the first door, no matter your access controller is DS-
K2601, DS-K2602 or DS-K2604, the binary value of the entrance card reader should be 1000 0000 and
the binary value of the exit card reader should be 0100 0000.
Step 2: RS-485 Wiring
Please connect card reader to access controller as following picture:
Note
1. Actually you can find RS485 A/B/C/D interfaces in access controller; we extend RS485 A interface
to the wiring distribution for easier cable connection and we use RS485B interface for backup, the
cable connection as following picture:
2. About wiring materials, we suggest customer choose RVVP cable.
RS485-
RS485+
GND
+12V
RS485 A+
RS485 A-
RS485 B+
RS485 B-

Title:
DS-K1100 Series Card Readers Connect
to DS-K2600 Series Access Controllers
by RS-485
Version:
v1.0
Date:
6/21/2017
Product:
Access Control Device
Page:
4 of 4
First Choice for Security Professionals
HIKVISION Technical Support