HIK VISION DS-K4E100 User manual

Title:
DS-K4E100 Connect to Access Controller or Access
Control Terminal
Version:
v1.0
Date:
03/31/2020
Product:
Access Control Devices
Page:
1 of 6
© Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: [phone] • Fax: [phone]
E-Mail: [e-mail] •www.hikvision.com
Preparation
1. Access Controller 2600 series
2. Access Control Terminal
3. Lock DS-K4E100
DS-K4E100 Connect to Access Controller or Access Control Terminal
This document is simply used to guide users how to wire correctly and ensure access
control terminal or K2600 controller can control lock K4E100.
K4E100 Working Principle:
The lock tongue will be extended and locked when the V+ (12V) & GND power up. And
when the L + and L- terminals are powered immediately (＞5V), the lock tongue will retracted
to unlock.

Title:
DS-K4E100 Connect to Access Controller or Access
Control Terminal
Version:
v1.0
Date:
03/31/2020
Product:
Access Control Devices
Page:
2 of 6
© Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: [phone] • Fax: [phone]
E-Mail: [e-mail] •www.hikvision.com
Wiring Type 1：
Access Control Terminal Connection:
NO COM
12V
GND
V+
GND
L+
L-
Access Control Terminal
Power
Note:
1) The power output power is recommended to be above 12V / 1A.
2) The DS-K4E100 is normally open (The Lock will unlock when L + / L- terminals
powered), so need connect to Access Control Terminal NO / COM output.
3) This wiring method is also applicable to all kinds of door station in Hikvision
video intercom products.
Wiring Type 2：
Access Controller 2600 series:
12V
GND
V+
GND
L+
L-
K2600 Controller
DS-K4E100
Power
Lock +
Lock -

Title:
DS-K4E100 Connect to Access Controller or Access
Control Terminal
Version:
v1.0
Date:
03/31/2020
Product:
Access Control Devices
Page:
3 of 6
© Hangzhou Hikvision Digital Technology Co.,Ltd. All Rights Reserved.
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China • Tel: [phone] • Fax: [phone]
E-Mail: [e-mail] •www.hikvision.com
Note:
1) The power output power is recommended to be above 12V / 1A.
2) The DS-K4E100 is normally open (The Lock will unlock when L + / L- terminals
powered), so K2600 Controller relay need configure to NO / COM output.
3) This K2600 Lock+ and Lock- have connect 12V power already，so not need
connect to additional 12V power。
Simple problems to deal with
1. Not locked after closing；
A. Check whether the power supply is normal, whether the voltage is normal, the
wiring is correct unlock signal instantaneous DC12V.
B. Check the door lock and vice lock gap is too large, the door sensor can't
induction if gas is more than 8mm.
C. Check the lock body and vice lock body installation position is not accurate
cause lock tongue sticking out lock.
2. Give unlock signal, but does not unlock
A. Check the wiring is correct
B. Check unlock voltage is correct, a voltage greater than the normal requirement
unlock DC5V.
3. Manual unlocking is not flexible, cylinder rotating connectors have misplaced stuck,
check whether the lock of a foreign body stuck phenomenon.
See Far, Go Further
HIKVISION Technical Support