Home Styles 4410-95 User manual

Part List
I.
Divider
1 pc.
4410-95
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Kitchen Cart
Refer to later page(s) of these
instructions for drawer assembly.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
2 pcs.
A.
Top
1 pc.
E.
Rail
1 pc.
F.
Rail
1 pc.
H.
Back Rail
1 pc.
K.
Base
1 pc.
Q.
Drawer
1 pc.
P.
Drawer
1 pc.
O.
Door
2 pcs.
J.
Back Panel
1 pc.
N.
Door
2 pcs.
M.
Shelf
2 pcs.
G.
Back Rail
1 pc.
L.
Shelf
4 pcs.
Tool(s) required for assembly: Phillips screwdriver
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Hardware List
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
Cam Lock
29 pcs. (+4 extra)
Cam Lock Screw
29 pcs. (+4 extra)
Cover
25 pcs. (+4 extra)
Dowel
49 pcs. (+1 extra)
M3.5x12
Wood Screw
24 pcs. (+1 extra)
M7x50
ScrewAssembly
17 pcs. (+1 extra)
Left Runner
2 pcs.
M3.5x12
Magnet Screw
8 pcs. (+1 extra)
Magnet
4 pcs.
M x164
Caster Screw
24 pcs. (+1 extra)
Locking
Caster
2 pcs.
Non-Locking
Caster
4 pcs.
Left Guide
2 pcs.
Side Bar
2 pcs.
Adjustable Pin
24 pcs. (+1 extra)
M4x22
Machine Screw
12 pcs.
M3.5x50
Flat Head Screw
8 pcs. (+1 extra)
Plastic Clip
8 pcs. (+1 extra)
Plate
4 pcs.
Insert
8 pcs.
M3.5x19
Plastic Clip Screw
8 pcs. (+1 extra)
Handle
6 pcs.
M3x12
Plate Screw
4 pcs. (+1 extra)
M7x10
Varianta Screw
8 pcs. (+1 extra)
Right Guide
2 pcs.
Hinge
8 pcs.
Right Runner
2 pcs.
Assembly Instructions 2/11

Assembly Instructions 3/11
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
STEP 1
Insert Cam Lock Screws into pre-drilled in Top (A), Side Panels (B), (C)
and Back Rail (G), then tighten. (See Figure 1)
Attach Left Guide to Side Panel (B) and
Right Guide to Side Panel (C) with Varianta Screws.
(See Figure 2)
Attach Left Guide and Right Guide to
Divider (I) with Varianta Screws.
Attach Magnets to Rail (E) with
Magnet Screws into pre-drilled holes.
(See Figure 3)
A
B
C
Magnet Screw
Magnet
Left Guide
Varianta Screw
Cam Lock Screw
Right Guide
STEP 2
Attach Casters to
Base (K) with
Caster Screws into
pre-drilled holes, with
Locking Casters at front.
(See Figure 4)
Note: Arrow label indicates front of Base (K).
Figure 4
Arrow label at front
K
Locking Caster
Non-Locking Caster
Caster Screw
I
G
E
Figure 1
Figure 2 Figure 3

Assembly Instructions 4/11
STEP 5
Attach Middle Panels (D)
to unit with Dowels and
Assembly Screws.
STEP 4
Attach Rail (E) and unit from Step 3
to Divider (I) with Dowels
and Assembly Screws.
Assembly Screw
Dowel
Assembly Screw
Dowel
D
D
I
STEP 3
Attach Rail (F) to Back Rail (G)
with Dowels and Cam Locks. (See Figure 5)
Cover Cam Locks with Covers. (See Figure 6)
Cover
Cam Lock
Dowel
Figure 6 Figure 5
F
G
E

Assembly Instructions 5/11
Dowel
Dowel
Cover
Cam Lock
Cover
Cam Lock
STEP 6
Attach Side Panel (C) to
unit with Dowels and Cam Locks.
Attach Back Rail (H) to unit with Dowel and Cam Lock.
Cover Cam Locks with Covers.
STEP 7
Slide Back Panel (J) into position.
Attach Side Panel (B) to unit with Dowels and Cam Locks.
Cover Cam Locks with Covers.
C
B
H
J

Instructions 3/6
Assembly Instructions 6/11
STEP 8
Attach Base (K) to unit with Dowels
and Assembly Screws.
STEP 9
Turn unit to its upright position.
Attach Top (A) to unit
with Dowels and Cam Locks.
Cover Cam Locks with Covers.
Attach Plastic Clips to unit with
Plastic Clip Screws. (See Figure 7)
Figure 7
Cam Lock
Cover
Dowel
Plastic Clip Screw
Plastic Clip
Dowel
Assembly Screw
K
A

Part List
P2.
Drawer Back
1 pc.
P5.
Drawer Bottom
1 pc.
P6.
Support
1 pc.
P1.
Drawer Front
1 pc.
P3.
Drawer Side
1 pc.
P4.
Drawer Side
1 pc.
P5
P6
Drawer (P)
Cam Lock
Cam Lock Screw
Dowel
Flat Head Screw
P1
P2
P3
P4
Dowel
Cam Lock Screw
Cam Lock
Cover
STEP 10
Attach Drawer Sides (P3) and
(P4) to Drawer Front (P1) with
Cam Lock Screws, Dowels and Cam Locks.
Cover Cam Locks with Covers.
Handle
Plastic Clip Screw
Plastic Clip
Wood Screw
Left Runner
Roller at back
Right Runner
Assembly Instructions 7/11
STEP 11
Slide Drawer Bottom (P5) into groove.
Attach Support (P6) and Drawer Back (P2)
to unit with Cam Lock Screws, Dowels,
Cam Locks and Flat Head Screws.
STEP 12
Attach Left Runner and
Right Runner to unit with Wood Screws.
Attach Plastic Clips to unit with Plastic Clip Screws.
STEP 13
Attach Handle with Machine Screws.
Machine Screw

Part List
P5
Drawer (Q)
Cam Lock
Cam Lock Screw
Dowel
Flat Head Screw
P2
Dowel
Cam Lock Screw
Cam Lock
Cover
STEP 14
Attach Drawer Sides (P3) and
(P4) to Drawer Front (Q1) with
Cam Lock Screws, Dowels and Cam Locks.
Cover Cam Locks with Covers.
Handle
Plastic Clip Screw
Plastic Clip
Wood Screw
Left Runner
Roller at back
Right Runner
Assembly Instructions 8/11
STEP 15
Slide Drawer Bottom (P5) into groove.
Attach Support (P6) and Drawer Back (P2)
to unit with Cam Lock Screws, Dowels,
Cam Locks and Flat Head Screws.
STEP 16
Attach Left Runner and
Right Runner to unit with Wood Screws.
Attach Plastic Clips to unit with Plastic Clip Screws.
STEP 17
Attach Handle with Machine Screws.
Machine Screw
P2.
Drawer Back
1 pc.
P5.
Drawer Bottom
1 pc.
P6.
Support
1 pc.
Q1.
Drawer Front
1 pc.
P3.
Drawer Side
1 pc.
P4.
Drawer Side
1 pc.
P3
Q1
P6
P4

Assembly Instructions 9/11
STEP 18
Insert Adjustable Pins into side panels and middle panels at desired level. (See Figure 8)
Place Shelves (L) and (M) into position.
STEP 19
Attach Side Bars to unit with Head Cap Bolts into pre-drilled holes.
Insert Inserts into pre-drilled holes in unit. (See Figures 9 and 10)
Insert Hinges into Inserts. (See Figure 11)
Adjustable Pin
Hinge
Insert
Side Bar
Head Cap Bolt
Insert
Figure 9
Figure 10
Figure 11
LM
LML
L
Figure 8

Assembly Instructions 10/11
STEP 20
Place Doors (N) and (O)
face down on a soft cloth.
Attach Hinges to Doors (N) and (O)
with Wood Screws into pre-drilled holes.
(See Figure 12)
Attach Plates to
Doors (N) and (O)
with Plate Screws into
pre-drilled holes. (See Figure 13)
STEP 21
Insert Doors (N) and (O)
Hinges into Inserts
in unit. (See Figure 14)
Attach Doors (N) and (O) to unit
with Wood Screws into pre-drilled holes. (See Figure 15)
Attach Handles to Doors (N) and (O) with Machine Screws.
Slide Drawers (P) and (Q) into position.
O
O
Plate Screw
Plate
Wood Screw
Hinge
Figure 14 Figure 15Figure 13Figure 12
Q
Insert
Hinge
Machine Screw
Handle
Wood Screw
P
N
N
N
N
OO

Assembly Instructions 11/11
Figure 18
Figure 16
Figure 19
Figure 17
Figure 20
If needed, doors may be adjusted for large or uneven gaps between them.
(See Figures 16 and 17)
Loosen Wood Screws attaching Hinge to door. (See Figure 18)
Slide door left to right as needed to adjust gap. (See Figure 19)
Re-tighten Wood Screws attaching Hinge to door. (See Figure 20)
Uneven Gap
Large Gap
Door
Hinge
Wood Screw
STEP 22

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460