Home Styles 88 5181 31 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
88 5181 31
Dining Table
IMPORTANT
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
B.
Top
1 pc.
C.
Leaf
1 pc.
D.
Table Slide
2 pcs.
E.
Leg
4 pcs.
Key Wrench
1 pc.
M8x50
Bolt
8 pcs. (+1 extra)
M3.5x40
Wood Screw
16 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Spring Washer (small)
8 pcs. (+1 extra)
Flat Washer (small)
8 pcs. (+1 extra)
M6x45
Head Cap Bolt
8 pcs. (+1 extra)

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
DD
A
B
Spring Washer (small)
Head Cap Bolt
Flat Washer (small)
Figure 1
STEP 2
Attach Top (A) to Top (B) by aligning dowels with the holes and firmly
pushing together.
Engage the locks by turning their handles clockwise 1/4 turn. (See Figure 2)
Attach Table Slides (D) to unit with Flat Washers (small), Spring Washers
(small) and Head Cap Bolts.
Tighten Wood Screws. (See Figure 3)
DD
A
B
STEP 1
Place Tops (A) and (B) upside down
on a soft cloth.
Remove Table Slides (D) from their packing position by loosening
and removing Flat Washers (small), Spring Washers (small) and
Head Cap Bolts. (See Figure 1)
Note: These 4 Flat Washers (small), Spring Washers (small) and
Head Cap Bolts will be used in Step 2. Do not discard.
Figure 2
Spring Washer (small)
Head Cap Bolt
Flat Washer (small)
Wood Screw
Figure 3

Assembly Instructions 3/3
E
E
E
E
Figure 4
Spring Washer
Bolt
Flat Washer
C
STEP 4
Disengage the locks by turning their handles counter-clockwise. (See Figure 5)
Pull out both sides of the table, then place Leaf (C) in the unit,
aligning the dowels with the holes.
Push the table together firmly, then engage the locks by turning their handles
clockwise 1/4 turn.
Level unit by adjusting the adjustable levelers on the bottom of legs. (See Figure 6)
Figure 5
Figure 6
STEP 3
Attach Legs (E) to unit with Flat Washers, Spring Washers and Bolts. (See Figure 4)
Turn table over to its’ upright position.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319