Honeywell DC515 Series User manual

Installation and Operation Guide
Portable and Plug-In Wireless Doorbell
English
German
French
Dutch
Spanish
Portuguese
Italian
DC515XX
Preparation
Doorbell
Push
Button
Flat Head
Screws
Phillips Screwdriver
Standard Screwdriver
Push Button Mounting
Bracket
and Adhesive Pad
To install you will need
Content will vary according to your kit
The push button supplied with this kit is pre-programmed to operate with the doorbell.
If it is not, see “Connect a Push Button” on page 7. Push button model may vary
from the one shown above.
CR2032 Battery
Mounting Bracket
Wall
Anchors
Round Head
Screws

2
Change the Light Pattern
Press the Sunlight button to change the lights that ash
when the doorbell rings.
Press the Sunlight button
1 time 2 times 3 times 4 times
Halo light and
top lights
Halo light only Top lights only No lights
Overview
Just follow these simple steps:
1. Install the push button battery. Depending on the model, plug in the
doorbell or install the batteries in it.
2. Set up the doorbell and your preferences.
3. Install the push button.
Doorbell for indoor use only. Do not expose to liquid, vapour or rain.
Power-up
1. Choose an outlet location that is not near a heat
source, where the doorbell will be easy to see and
hear and power it.
2. Open the push button battery cover and install the
CR2032 battery.
Setup and Operation
Press the push button to test whether it is paired with the doorbell. The
doorbell will light up and ring. If it does not, see “Connect a Push Button” on
page 7.
+

3
Change the Tune
Press the Music button to change the doorbell tune.
Every time you press the Music button, the tune will
change. Stop pressing the Music button when you hear
the tune you want.
If you have multiple push buttons paired with the chime,
you can select the melody for the last push button that
was triggered.
Press the push button. (For any new push button, ensure
that it is paired rst. Refer to “Connect a Push Button” on
page 7.)
Within 12 seconds, press the melody selection button
until the desired tune is selected.
Ding Dong
Westminster
Piano
Fantasy
Soft Alert
Smart Sax
Change the Halo Light Colour
Press the push button.
Within 12 seconds, press the Sunlight
button.
Light Blue
White
Red
Dark Blue
Green
Purple
Yellow
Every time you press the Sunlight
button, the halo light will change
colour. Stop pressing the Sunlight
button when you see the colour you
want:
Adjust the Volume
Press the Volume
Up or Volume
Down buttons to
adjust the volume
of the Doorbell.
Mute the Doorbell
Press the
Mute button
to silence the
doorbell.

4
Install Push Button
1. Mount the push button
bracket in the desired
location. Use the screws.
–OR–
Use the adhesive backing. If
using the adhesive backing,
clean the surface first.
2. Snap the push button onto
the mounting bracket.

Note: If you need to remove the push button, use a small
screwdriver to release the tab.
Set the Mute
You can also mute the doorbell for specic amounts of time.
Press the Mute button.
Mute button shows Doorbell is mute
1 time doorbell is mute
2 times 3 hours
3 times 6 hours
Mute button shows Doorbell is mute
4 times 9 hours
5 times 12 hours
6 times no longer mute
It is also easier to unmute the doorbell by pressing and holding the mute
button until it beeps.

5
Wall Mount Installation (Portable Models Only)
Choose a location that is not near a heat source or on something that moves
(like a door). For non-mounting locations, choose a place where the doorbell
will be easy to see and hear.
Install Doorbell
If you are not mounting the doorbell to the wall, place the doorbell where you
want it.
1. Screw the doorbell wall mounting
bracket to the wall using the
included screws and
anchors (if necessary).
Drill 1/4-inch holes for
the anchors.
2. Hang the doorbell on
the mounting bracket.
For DC515XX
models

6
Before linking your outdoor motion
sensor, you will need to adjust its
settings:
Turn the Dusk control and Time control
fully anti-clockwise to its minimum
setting.
Ensure your sensor is in Day Mode. This
will be shown by the slider button being
in the left position (Sun symbol).
Connect a Motion Sensor
1. Press and hold the Setting button on
the doorbell for three seconds.
The halo light will circle.
2. Within 20 seconds of pressing the
Setting button, wave or make some
other kind of motion in front of the
motion sensor.
Accessories
You can connect up to 4 accessories to your doorbell, including other push
buttons, window or door opening sensors, and motion sensors.
If you try to connect more accessories than the maximum number, the
doorbell will sound two beeps.

7
Models nly)
Your doorbell can also be used as a night-light.
1. Plug the doorbell into a wall outlet.
2. Press and hold the Night-light button to select the
halo colour.
3. Release the Night-light button when you see the
colour you want.
Secret Knock
For each push button, you can set up a Secret Knock
that has a different ring and halo light colour. The
Secret Knock is triggered by pressing the push button
quickly 3 times.
1. Press the push button 3 times quickly.
2. Within 12 seconds of pressing the push button, press the Music button to
select the ring for the Secret Knock.
3. Within 12 seconds of pressing the push button, press the Sunlight button
to select a halo light colour for the Secret Knock.
Connect a Push Button
Follow these steps to change the ring and halo light colour for an existing
doorbell, too.
1. Press and hold the Setting button on
the doorbell for three seconds.
The halo light will circle.
2. Press the push button.
3. Within 12 seconds of pressing the
push button, press the Music button
to select the ring for that push
button.
4. Within 12 seconds of pressing the
doorbell, press the Sunlight button
to select a halo light colour for that
push button.
Plug socket shown
above for reference
will vary by country/
region

8
Maintenance
Your doorbell and push button require no maintenance except to periodically
change the battery.
If using the correct battery, its life should be approximately:
• Up to 2 years for the push button; replace with CR2032 lithium battery
Low Battery Notification
When the push button batteries are low, two beep sounds are heard after the
normal tune.
When the batteries are low on the portable doorbells (battery models), the
bottom edge of the halo light ashes yellow every 6 seconds until the batteries
are replaced.
Reset
This process removes all pairings, including the push button that came with
this doorbell:
1. Unplug the doorbell or remove the batteries from the portable model.
2. Press and hold the Setting button and plug the doorbell back in at the
same time.
3. The halo light will circle and the doorbell is returned to its default factory
settings.

9
Specications
Doorbell Push Button
Operating Temperature  
Honeywell Home ActivLink™ 868 MHz 868 MHz
  
 84 dB -
Battery Type 
models only 
 Up to 2 years - battery models
only Up to 2 years
Rain proof N/A IP55
Troubleshooting
If Then
The doorbell does not work
 
 Ensure the correct batteries are installed in both the push and doorbell

 The doorbell might be out of range; try the doorbell in a different

 
 
 

 
 
Two ‘beep’ sounds are
heard after the normal tune 
Range is reduced
 

 
 

*Under these scenarios the push button is considered the “transmitter”. Other
examples of transmitters are the wireless motion (PIR) sensor or wireless door
window sensor.

www.resideo.com
©2019 Resideo Technologies, Inc.
All rights reserved. The Honeywell Home trademark is used under
license from Honeywell International Inc.
32343180-001 Rev.A
https://livewell.honeywellhome.com