Honeywell Domonial User manual

USER MANUAL
DOMONIAL

Congratulations on the purchase of your DOMONIAL security system
This system is designed to operate on an authorised radio frequency and
will in no way endanger the user.
To make the best out of your system we advise you to read this manual
carefully.

3
INDEX
1 Introduction to the security system 4
2 Understanding the system tones 6
3 How to use the wireless keypad with display* 8
4 How to use the wireless keypad with prox reader 22
5 How to use the keyfob with 1 LED 26
6 How to use the keyfob with 3 LEDs 28
7 Understanding detector* operation 31
8 How to control your system over the telephone 32
9 Maintenance and recommendations 34
*Optional: your installation may include one or more controlling devices and/or one or more detectors.

4
Introduction to the security system
The Domonial control panel/communicator unit is the brain of your
security system. It exchanges information with the associated wireless
peripherals. The control panel centralises the data sent by the detectors,
records the arming and disarming operations and communicates with
your Alarm Company. The control panel also includes a speaker for alarm
signalling and audio verification.
CHARACTERISTICS
RADIO
 Narrow band frequency modulation
 Identification code specific to each component
(no possible interference between neighbouring systems)
 Protection against attempted jamming
 Radio monitoring of the system detectors and sirens
ELECTRICAL
 240V mains with battery backup
 Built-in voltage surge protection
 System supply monitoring
TRANSMISSION
 Built-in telephone transmission
 Telephone line loss detection
 Transmission monitoring by periodical tests
 Optional GSM transmitter
OPERATIONAL
Up to 3 protected sets : total set, partial set, annex set
Up to 30 detectors
 Alert functions
 Control panel and detectors protected against tampering
1

Indicators 2, 3, 4 and 5 show the faults, which are occurring or in memory for one set at a time.
Indicators are only active when the system is unset and during the arming and disarming
phases. When the system is set, the indicator lights turn off after a few seconds.
1- LED INDICATOR “SYSTEM ARMED”
On: Total set is being armed.
Flashing slowly: Partial set is being armed.
Flashing quickly: Annex set is being armed.
Off: The system is disarmed.
2- LED INDICATOR “SET ASSOCIATED WITH FAULT”
On: Faults indicated on LEDs 3, 4, and 5 correspond to the total set.
Flashing slowly: Faults indicated on LEDs 3, 4, and 5 correspond to the partial set.
Flashing quickly: Faults indicated on LEDs 3, 4, and 5 correspond to the annex set.
OFF: Faults indicated on LEDs 3, 4, and 5 correspond to the entire system.
3- LED INDICATOR “SYSTEM FAULT”
On: A system fault is occurring on set indicated on LED 2.
System faults include battery or power failure, supervision fault, phone line failure or
radio Jamming. Please contact your alarm company if this indication persists.
Flashing slowly: A system fault is in memory on set indicated on LED 2 and requires a reset.
Off: No system fault.
4- LED INDICATOR “TAMPER ALARM”
On: A tamper alarm is occurring on set indicated on LED 2.
Flashing slowly: A tamper alarm is in memory on set indicated on LED 2 and requires
a reset.
Off: No tamper alarm.
5- LED INDICATOR “INTRUDER ALARM”
On: An intruder alarm is occurring or a detector is triggered on set indicated on LED 2.
This includes open door-contact, movement detection or smoke detection.
Flashing slowly: An intruder alarm is in memory on set indicated on LED 2 and requires
a reset.
Flashing quickly: A confirmed alarm is in memory and requires a remote reset. Please call your
monitoring operation at the alarm company.
Off: No intruder alarm.
INDICATOR LIGHTS
The front cover of the control panel features LED indicators which show the status of your
security system.
5

Understanding the system tones
SIRENS
A siren is an effective deterrent due to its power and very irrating tone. The system has a siren built
into the control panel, and an optional outdoor and/or indoor wireless siren can be added.
The panel siren emits an audible confirmation tone when arming and disarming the security
system and a fire tone when a smoke detector is triggered. Volume levels can be adjusted by
the installer.
6
2

7
SYSTEM TONES
TOTAL SET
ARMING
DISARMING
PARTIAL SET
ARMING
ANNEX SET
ARMING
FAULT
ALERT
ENTRY
DELAY
Sequence of 3 modulated sounds
Duration : 4 seconds
When arming, total set, confirms that the
control panel has received a valid code or
TAG and is preparing to arm total set.
When Disarming, confirms that the control
panel has been successfully disarmed.
When arming the partial set, confirms that
the control panel has received a valid code
or TAG and is preparing to arm partial set.
This signal indicates a fault in the system.
Confirms the transmission of an alert to the
alarm company.
This entry tone sounds for 30 seconds*
after you open the entry door. You should
disarm your system within this time.
Long and continuous beep
Duration : 2,5 seconds
Sequence of 2 modulated sounds
Duration : 2,5 seconds
2 times 7 fast beeps
4 beeps upon alert ...
sent via the keypad
Upon entry...
one beep per second
EXIT DELAY
Total set arming: beeps continue until final
exit door is closed.
Partial set arming: beeps continue for 30s*
until partial set is armed.
Upon arming ...
one beep per second
ARMING
COMPLETE
When closing the final exit door, confirms
that the system is armed.
After closing the final door
Three fast beeps
* Defined by user during installation

8
The wireless keypad with display offers a complete range of tools to manage your alarm system,
from normal operation to dedicated user functions. This keypad is optional, but 1 to 4 keypads of
this type may be included with this system.
The keypad is used to arm and disarm your security system using a valid access code or key TAG.
The master code or TAG is required to modify other users’ codes and TAGs, and to authorise the
alarm company to access the system for maintenance.
Other user functions include remote control of electrical equipment*, manual bypass of detectors,
setup of beeps and equipment testing.
This keypad also provides full system status information, with display icons, messages, and beeps
emitted by the keypad. You can also view the history of alarms that have occurred.
NB: This keypad is suitable for indoor use only.
* This function requires an optional X10 extension with X10 receivers.
3
INTRODUCTION TO THE TCU KEYPAD
TAG identification
area
Total set
arming key
Partial set
arming key
Disarming / Go to
previous menu /
Cancel choice key
Shortcuts and
menu browsing key
Validation &
Status key
Screen
Codes/text
entry keypad
Total set
arming light Partial set
arming light
Shortcuts and menu
browsing key
Keytag (TAG)
for identification
How to use the wireless keypad with display

►Press the keys to enter the main menu.
►Navigate through the menus with and
►Confirm your choices with
►Abort your choice with
►Return to the main menu with
1
Total set armed
Partial set disarmed
System disarmed
Annex set armed
Annex set
disarmed
Receiver 1 'ON'
Receiver 2 'ON'
Alarm in memory
Power supply fault
Tamper fault*
Radio transmission*
in progress
System fault*
State of keypad battery
Blinking: replace
keypad battery
Silent mode
Bypassed detector
Detector activated
*Please contact your installer
if these faults persist
Message area
Menu scrolling and
choice validation
THE TCU SCREEN AND ICONS
The TCU display clears after a few seconds in order to save energy.
THE TCU MENUS
9
1 - ANNEX
2 - EVENTS
3 - TOOLS
4 - USERS
5 - TESTS
6 - PREFERENCES
THE MAIN MENU

10
ANNEX
This menu is used to arm or disarm the Annex set. See Arming of the Annex Set, on
page 11.
EVENTS
The security system records events with their time and date. These can be viewed from
the keypad when the system is disarmed.
TOOLS
This function allows you to control receivers, detectors, and so on. Refer to The Tools
Menu, on page 17 for complete instructions.
USERS
Use this function to specify the users of your installation.
The master user must be identified by his code or TAG.
This menu item is described in detail in The Users Menu, on page 15.
TESTS
You can initiate tests of your security system to confirm that it is operating correctly.
There are three options: Sirens, lights, maintenance.
Sirens: Each siren operates in turn for 5 seconds
Lights: All indicator lights on the control panel and keypad light for 5 seconds.
Maintenance: This function can be active or inactive, depending on your configuration.
It allows you to control certain functions from a distance. See your installer for details.
PREFERENCES
This function allows you to choose various modes of operation, and activate or
deactivate the panel siren’s beeps. See The Preferences Menu, on page 19.
THE SUB-MENUS