Honeywell WAVE2EX - Ademco Two Tone Siren Assembly instructions

ADEMCO LYNXR-I
Security Systems
Installation and Setup Guide
AWAY
OFF
STAY
AUX
LIGHTS ON
RECORD
LIGHTS OFF
STATUS
TEST
VOLUME
CODE
NO DELAY
BYPASS
PLAY
CHIME
FUNCTION
DELETE
ESCAPE
ADD
SELECT
ARMED READY
456
789
0#
123
K14114 3/06 Rev. B

- 2 -
RECOMMENDATIONS FOR PROPER PROTECTION
The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide
Proper Coverage for the Protected Premises.
Recommendations for Smoke and Heat Detectors
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations
contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.
•Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of
the household as follows: For minimum protection a smoke detector should be installed outside of each separate sleeping
area, and on each additional floor of a multi-floor family living unit, including basements. The installation of smoke
detectors in kitchens, attics (finished or unfinished), or in garages is not normally recommended.
•For additional protection the NFPA recommends that you install heat or smoke detectors in the living room, dining
room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.
In addition, we recommend the following:
•Install a smoke detector inside every bedroom where a smoker sleeps.
•Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely closed. Smoke
could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the sleeper if the door is
closed.
•Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air conditioners or
humidifiers) are used.
•Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.
•Install smoke detectors in any room where an alarm control is located, or in any room where alarm control connections
to an AC source or phone lines are made. If detectors are not so located, a fire within the room could prevent the control
from reporting a fire or an intrusion.
THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE
SOUNDING OF FIRE NOTIFICATION APPLIANCES.
DINING KITCHEN
BEDROOM
BEDROOM
.
Smoke Detectors for Minimum Protection
Smoke Detectors for Additional Protection
Heat-Activated Detectors
BEDROOMBEDROOM
BEDROOM
BEDROOM
LIVING
ROOM
TV ROOM
DINING
LIVING ROOM
LIVING ROOM
BASEMENT
BEDROOMBEDROOM
BEDROOM
CLOSED
DOOR
GARAGE
KTCHN
KITCHEN
TO
BEDROOM
01000-002-V0
Recommendations For Proper Intrusion Protection
•For proper intrusion coverage, sensors should be located at every possible point of entry to a home or premises. This
would include any skylights that may be present, and the upper windows in a multi-level building.
•In addition, we recommend that radio backup be used in a security system. This will ensure that alarm signals can be
sent to the alarm monitoring station in the event that the telephone lines are out of order (alarm signals are normally
sent over the phone lines, if connected to an alarm monitoring station).

- 3 -
Table of Contents
SYSTEM FEATURES ..................................................................................................................................4
MOUNTING THE CONTROL.....................................................................................................................5
WIRING CONNECTIONS...........................................................................................................................6
CONNECTING/CONFIGURINGCOMMUNICATIONS DEVICES .........................................................8
AC POWER AND BACKUP BATTERY....................................................................................................11
INSTALLING WIRELESS ZONES...........................................................................................................13
MECHANICS OF PROGRAMMING ........................................................................................................16
ZONE RESPONSE TYPE DEFINITIONS ...............................................................................................18
DATA FIELD DESCRIPTIONS ................................................................................................................20
✻56 ENHANCED ZONE PROGRAMMING MODE ................................................................................29
✻80 DEVICE PROGRAMMING MENU MODE ......................................................................................34
✻81 ZONE LIST MENU MODE................................................................................................................37
✻83 ENHANCED SEQUENTIAL MODE ................................................................................................38
✻84 ASSIGN ZONE VOICE DESCRIPTORS ..........................................................................................41
✻85 RECORD CUSTOM VOICE DESCRIPTORS...................................................................................43
VOICE PROMPT PROGRAMMING.........................................................................................................44
REMOTE PROGRAMMING/CONTROL (DOWNLOADING) ................................................................48
SYSTEM OPERATION..............................................................................................................................50
TESTING THE SYSTEM ..........................................................................................................................56
SYSTEM COMMUNICATION ..................................................................................................................57
TROUBLESHOOTING GUIDE ................................................................................................................59
PROGRAMMING DEFAULT TABLES....................................................................................................62
INDEX.........................................................................................................................................................65
REGULATORY AGENCY STATEMENTS ..............................................................................................68
LIMITATIONS OF THIS SYSTEM STATEMENT..................................................................................69
SPECIFICATIONS.....................................................................................................................................70
CONTACTING TECHNICAL SUPPORT.................................................................................................70
SUMMARY OF CONNECTIONS DIAGRAM ..........................................................................................71
WARRANTY ............................................................................................................................... Back Cover

LYNXR-I Installation and Setup Guide
- 4 -
System Features
U
UU
UL
LL
L
LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.
Powerline Carrier Devices have not been evaluated by UL.
The LYNXR-I control is a self-contained, rechargeable wireless control/communicators that feature easy
installation and usage. A built-in speaker provides voice annunciation of system status along with voice
descriptors of each zone. An internal module (if provided) allows the LYNXR-I to communicate with the
Central Station via the Internet. The following illustration highlights the main features of this system.
AWAY
OFF
STAY
AUX
LIGHTS ON
RECORD
LIGHTS OFF
STATUS
TEST
VOLUME
CODE
NO DELAY
BYPASS
PLAY
CHIME
FUNCTION
DELETE
ESCAPE
ADD
SELECT
ARMED READY
456
789
0#
123
ZONES and DEVICES
•Up to 24 wireless zones
(5800 Series Transmitters)
•Up to 16 wireless button zones
•Up to 8 Powerline Carrier Devices
•Supports wireless keypads
8 USER CODES
•Installer code
•Master code
•5 Secondary codes
•Duress code
•3 Panic functions
ALARM OUTPUT
•Built-in sounder
•Piezo output
(30mA max.)
•Bell output
(120mA max.)
•Steady output for
burglary/panic
•Temporal pulse
output for fire alarms
•Long Range
Radio/Audio alarm
verification
PROGRAMMING
•Options stored in EEROM
•Can be uploaded, downloaded or
controlled via IBM-compatible
computer using Compass
downloader software and specified
HAYES modem
•Voice Prompt programming mode
COMMUNICATION
•Ademco Low Speed
•Sescoa/Radionics
•Ademco Express
•Ademco Contact ID
•Paging feature
•Internet Central
Station Communication
•GSM Cellular Central
Station Communication
SYSTEM POWER
•Primary Power: Ademco K10145X10
Plug-in Transformer, 110VAC to
9VAC, 25VA output (K10145CN in
Canada)
•Backup battery: Rechargeable
nickel-metal hydride battery pack
rated at 7.7Vdc.
FEATURES
•Real-time Clock display and Fixed-Word display
•Message Center (for user recorded messages)
•Voice announcement of system and zone status
•Voice chime
•Alarm Clock
•Reminder
•X-10 Scheduling
•Latch Key Reports
•Automatic Stay Arming
•Remote Phone Control
•“Follow Me” Reminder and System Announcements
OTHER FEATURES
•Exit error feature (detects difference between an
actual alarm and exit alarm caused by leaving a door
open after the exit delay expires)
•Event log stores up to 84 events
•Macro/ 1-button paging
•RF Jam Detection
•Remote Phone Control
•Compatible with Encrypted (High-Security) Devices
SPECIAL FEATURES
•Two-way voice communication
•Speaker phone operation

LYNXR-I Installation and Setup Guide
- 5 -
Mounting the Control
Wall Mounting
The illustration below shows the front assembly separated from the back plate.
!
DO NOT disconnect the ribbon cable from the terminal strip board. Disconnect the cable only from the
front assembly board.
1. Release the front assembly from the back
plate by depressing the two locking tabs
at the top of the unit with the blade of a
medium size screwdriver.
2. Once these tabs have been released,
insert the screwdriver in the side of the
case and release the side locking tabs by
gently twisting.
3. Carefully disconnect the ribbon cable from
the front assembly, leaving the ribbon
cable connected to the terminal block
PC board. The back plate contains the
terminal block for making wiring
connections.
4. Mount the back plate to a sturdy wall,
feeding the field wiring through the
appropriate openings in the back plate.
5. After wiring connections are made,
carefully reconnect the ribbon cable to
the front assembly PC board connector
(properly aligning the red wire).
6. Snap the front assembly to the back plate
so it is secured by the locking tabs.
LOCKING
TABS
LOCKING
TABS
LOCKING TABS
RED WIRE
MARKING
DISCONNECT
THIS END ONLY!
07000-003-V1
Desktop Mounting
For desktop use the optional mounting base (model LYNX-DM, purchased separately) must be used.
1. Slide the control panel onto the mounting
base locking tabs.
2. Bring all wiring through the bottom of the
mounting base, using one of the three
wire entry locations, before making
connections to the control panel.
3. Use tie-wraps to secure the wiring to the
built-in wire loops as needed. Use the two
supplied screws to secure the control
panel to the mounting base.
ADD
ESCAPE
DELETE
SELECT
AWAY
OFF
STAY
AUX
01009-004-V1
WIRE ENTRY
KNOCKOUT
(1 of 3)

LYNXR-I Installation and Setup Guide
- 6 -
Wiring Connections
Wiring Overview
The following summarizes the connections required. Refer to the Wiring Connections paragraph and the
Summary of Connections diagram on the inside back cover when making connections.
U
UU
UL
LL
L
External sounders have not been evaluated by UL.
07000-005-V1
7845i-L COMMUNICATIONS PORT
(INTERNAL MODULE ONLY)
ALARMNET LRR/IP
COMMUNICATION PORT
LOCAL SOUNDER
DISABLE JUMPER
TERMINAL
STRIP
TELEPHONE
CONNECTIONS
STANDARD AND HIGH CAPACITY
BATTERY CONNECTOR
SUPER HIGH CAPACITY
BATTERY CONNECTOR
INCOMING
PHONE
LINE
TO
HANDSET
PHONE
LINE
WARNING:
TO PREVENT
RISK OF SHOCK
DISCONNECT
TELEPHONE LINE
AT TELECOM
JACK BEFORE
SERVICING
THIS UNIT.
WEEKLY TESTING IS
REQUIRED TO ENSURE
PROPER OPERATION
OF THIS SYSTEM
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
PREMISES
TELEPHONE
1234865 11
710 12 15 16
13 14
PHONE
FUTURE
USE
FUTURE
USE SOUNDERS PLCD AC
EARTH
GROUND
EARTH
GROUND
INCOMING
TELEPHONE
LINE
RING
TIP
RING
TIP ( ) ( ) (+)
(+)( )
PIEZO
6-14VDC
120mA max.
(e.g. WAVE2EX)
6-14VDC
30mA max.
DATA
OUT
SYNC
IN
POWERLINE CARRIER DEVICES
RJ11
8
POS
JACK
AC
AC
SYNC
COM
DATA
9
BELL
07000-009-V1
NOTE
USE ONLY THE K10145X10
OR K10145CN
TRANSFORMERS PROVIDED
K10145X10
PLUG-IN
TRANSFORMER
9VAC, 25VA
X10
ONLY
CONNECTIONS
GND
D ATA I N
GND
DATA OUT
LOCAL SOUNDER DISABLE
SHUNT REMOVE TO DISABLE
STANDARD/HIGH
CAPACITY BATTERY
CONNECTOR
SUPER HIGH CAPACITY
BATTERY CONNECTOR
ALARMNET LRR/IP
COMMUNICATIONS PORT
INTERNAL 7845i-L*
MODULE ONLY
THE LYNXR-I CONTROL IS COMPATIBLE WITH
THE FOLLOWING INTEGRAL RECHARGEABLE
BATTERY PACKS:
REPLACE EVERY FOUR YEARS
P/N LYNXRCHKIT-SC
P/N LYNXRCHKIT-HC
P/N LYNXRCHKIT-SHA
* WHEN AVAILBLE
UL NOTE
THE MINIMUM WIRE SIZE USED FOR TELEPHONE
INSTALLATIONS MUST BE #26 GAUGE
LYNXR-I Wiring Connections

LYNXR-I Installation and Setup Guide
- 7 -
Wiring Connections
1. Make Earth Ground Connection - The designated earth ground terminal (1) must be terminated in a good earth ground
for the lightning transient protective devices in this product to be effective. The following are examples of good earth
grounds available at most installations:
Metal Cold Water Pipe - Secure a non-corrosive metal strap (copper is recommended) to the pipe that is electrically
connected and secured to which the ground lead is electrically connected and secured.
AC Power Outlet Ground - Available from 3-prong, 120VAC power outlets only. To test the integrity of the ground
terminal, use a three-wire circuit tester with neon lamp indicators, such as the UL Listed Ideal Model 61–035, or
equivalent, available at most electrical supply stores.
a. Connect terminal 1 to a good earth ground.
2. Make Phone Line Connections - For local or full line seizure proceed to the appropriate steps below.
Local Seizure
a. Connect the incoming phone line to either the
8-position jack or terminals 2 (TIP) and 3
(RING) on the Lynx.
b. Connect the handset phone lines to either the
RJ11 jack or terminals 4 (TIP) and 5 (RING).
Full Line Seizure: The control must be
placed in series with the incoming phone
line. Plugging the Direct Connect Cord
directly into the RJ31X jack, allows the control
to seize the phone line when an alarm occurs
and normal phone line usage by the premises
phones if the plug needs to be removed.
c. Cut the incoming RING and TIP phone lines
(typically red and green, respectively) and
connect them to RJ31X terminals 4 (red) and
5 (green).
d. Connect the premises end of the cut RING
and TIP wires to RJ31X terminals 1 (grey) and
8 (brown) respectively.
e. Wire the flying leads of a Direct Connect Cord
to the control’s phone terminals as shown in
the diagram or plug into the 8-position jack.
f. Plug the Direct Connect Cord into the RJ31X
jack.
RJ31X
1
2
3
45
6
7
8
RING
TIP
INCOMING
PHONE LINE
TO
PREMISES PHONES
TIP RING TIP RING
BROWN
GREY
RED
GREEN
INCOMING
PHONE LINE
TO
PREMISES
PHONES
}
}
GREENRED
GREY BROWN
RING
TIP
DIRECT
CONNECT
CORD
OR
OR
8-POSITION
JACK
01000-008-V0
Full Line Seizure Connections
U
UU
UL
LL
L
Do not remove the local sounder shorting jumper (shunt).
External sounders and powerline carrier devices have not been evaluated by UL
LOCAL SOUNDER DISABLE: The Master Keypad’s built-in piezo sounder can be disabled by removing the
shorting jumper (shunt) on the terminal board. If disabled, however, no sounding will occur upon AC loss,
since the external sounder does not operate when AC power is lost.
3. Make External Sounder Connections - The control panel supports either a 6-14VDC piezo sounder (30mA max.) or
6-14VDC bell (120mA max.; e.g. ADEMCO WAVE2EX).
a. Connect a piezo sounder to terminals 10 (+) and 11 (–); OR a bell to terminals 11 (–) and 12 (+).
4. Disable Local Sounder Option - If required the Master Keypad’s built-in piezo sounder can be disabled.
a. Remove the shorting jumper (shunt) on the terminal board.
5. Make Powerline Carrier Device Connections - The control panel supports up to 8 Powerline Carrier Devices. If using
these devices, they must be connected to the K10145X10 transformer, as shown in the SUMMARY OF
CONNECTIONS diagram.
a. Connect the com/data/sync/ lines from the transformer to terminals 9, 13, and 14, respectively.
If not using the supplied connection cable, you may need to reverse the black and yellow wire connections.
Refer to the ✻
✻✻
✻80 Device Programming Menu Mode section for details on programming Powerline Carrier
Devices.

LYNXR-I Installation and Setup Guide
- 8 -
Connecting/Configuring Communication Modules
General
This LYNXR-I supports central station reporting via long range radio and internet. It also supports
upload/download programming capability via the Internet or a Private local area network (Intranet). This
allows site maintenance independent of central station monitoring, and modification to sites globally via the
Internet or through a private LAN. Refer to the instructions provided with the LRR/IP Communications
Device being installed for additional information regarding its installation, programming, and registration.
Zone 103 is the supervisory zone for the Communications Device.
LYNXR-I does not support the 7845i-ENT remote access feature.
Connecting Long Range Radio and Internet Communication Devices
Connect and configure the communications device as follows (refer to the Installation Instructions for device
that you are installing for additional information):
The wire run between the LYNXR-I and the Communications Device must not exceed ten (10) feet.
U
UU
UL
LL
L
The 7845ENT and 7845CV2 have been evaluated by UL for Household Burglary installations. The
communications modules have not been evaluated for Household Fire installations.
AlarmNet 7845i-L* Communications Device
1. Install the module into the LYNXR-I back plate and secure it with the two provided screws. Refer to the diagrams below.
2. Connect the provided ribbon cable between the module and the PC board. This cable provides DC power and ground for
the module and data in/data out connections.
3. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet
connection.
* When available. The 7845i-L module has not been evaluated by UL.
07000-004-V0
LRR / IP PORT
RJ45 (FOR INTERNET
CONNECTION)
COMMUNICATIONS
PORT FOR
INTERNAL 7845i-L
MODULE ONLY
7720P PROGRAMMER
CONNECTION
CABLE
Installing the 7845i-L Communications Module

LYNXR-I Installation and Setup Guide
- 9 -
AlarmNet 7845GSM*, 7845i-GSM*, 7845i-ENT or 7845i, Communications Device
!
The 7845i-ENT/7845i and 7845CV2 can not be used for installations requiring 24-hour standby.
1. Connect the 4-wire communications cable to the LRR/IP Communications port on the LYNXR-I.
2. Connect the four wires to the specific Communications device as shown in the accompanying figures.
3. If you are installing a 7845GSM or 7845i-GSM you must also install a jumper between terminals 2 and 3 on the
communications device.
4. Connect the device to the Internet via a cable/DSL modem and router or to an Intranet (LAN) via the appropriate Ethernet
connection, if applicable.
7845GSM / 7845i-GSM
LYNX
SUPER HIGH
CAPACITY
BATTERY
(OPTIONAL)
REQUIRED FOR
24-HR BACKUP
7845i-GSM-010-V0
GND
Z3 OR DATA OUT
Z1/Z2 OR DATA IN
ECP (+) VOLTAGE INPUT
RED
BLK
GRN
YEL
RED
BLK
GRN
YEL
4
5
6
3
5
4
4-WIRE CABLE (N4632-4)
1
2
TB1
LRR/IP COMMUNICATIONS PORT
LYNXR-I CONTROL PANEL
NC
+12 VDC
GND
D ATA I N
DATA OUT
LYNX
STANDARD
CAPACITY
BATTERY
Connecting AlarmNet 7845GSM* / 7845i-GSM*
* When available. The AlarmNet 7845GSM and 7845i-GSM modules have not been evaluated by UL.
7845i-ENT / 7845i
07000-013-V2
GND D ATA I N DATA OUT (+) VOLTAGE INPUT
RED BLK GRN YEL
RED
BLK
GRN
YEL
TB 1
LYNXR-I CONTROL PANEL
NC RED
BLK
GRN
YEL
+12 VDC
GND
D ATA I N
DATA OUT
4-WIRE CABLE (N4632-4)
LYNX
STANDARD
CAPACITY
BATTERY
LRR/IP COMMUNICATIONS PORT
Connecting AlarmNet 7845i-ENT/7845i

LYNXR-I Installation and Setup Guide
- 10 -
LRR/IP Communications Device 24-Hour Standby Power
If you are installing the AlarmNet 7845GSM/7845i-GSM or 7845i-L you must install the Super High Capacity battery
P/N WALYNX-RCHB-SHA in the LYNXR-I.
!
The 7845i-ENT/7845i and 7845CV2 can not be used for installations requiring 24-hour standby.
AlarmNet 7845CV2
1. Connect the 4-wire communications cable to the LRR/IP communications port on the LYNXR-I.
2. Connect the four wires to the 7845CV2 as shown below:
LRR/IP COMMUNICATIONS PORT
07000-011-V2
7845CV2
TB1
V+
GND
Z1/DATA IN
RAD FLT/ DATA OUT
P1 BAT
LYNXR-I CONTROL PANEL
RED
NC
BLK
GRN
YEL
RED
BLK
GRN
YEL
+12 VDC
GND
D ATA I N
DATA OUT
4-WIRE CABLE (N4632-4)
LYNX
STANDARD
CAPACITY
BATTERY
BATTERY
ADEMCO
K4362
Connecting AlarmNet 7845CV2
Configuring Long Range Radio and Internet Communication Devices
1. Enable the communications device in programming field *55 and configure alarm reporting and module supervision in
programming field *77.
2. Program the device as required using the 7720P programmer (refer to the Installation Instruction for the device that you
are installing for additional information). Note that the device address must be set to 3.
1. When programming an AlarmNet 7845CV2 the radio’s “current limit” most option must be set
to [Y] (yes).
2. The device must be registered before downloading or alarm reporting can take place.