Honeywell ADEMCO 745VSD3 Assembly instructions

K6210V1 2/09 Rev. C
ADEMCO 745VSD3
Voice Siren Driver
INSTALLATION AND SETUP GUIDE
FEATURES
•Generates siren as well as voice output in English,
Spanish, and French.
•Separate messages for FIRE, BURGLARY, and
Carbon Monoxide (CO) conditions.
•Separate siren sounds for FIRE, BURGLARY, and
Carbon Monoxide conditions.
•Terminal strip for secure connection to control panel.
•Selectable input level (High/Low) for
FIRE/BURGLARY/CO inputs.
•Supervision feature for speaker and speaker wiring.
•Compatible with 8 - 32 ohm speakers.
•Operates on 12-16V DC; 15mA standby current draw
•Small compact size for easy installation using double-
sided tape provided – measures 4” x 2-3/4” x 1-3/4”.
NOTE: 745VSD3 annunciates alarms in the following
priority order: FIRE, Carbon Monoxide (CO), Burglary.
WIRING CONNECTIONS
IMPORTANT: 745VSD3 must be mounted in the control
cabinet. Wiring connections to the terminals are as
follows:
234561
ON
78
745VSD3-001-V0
SW 1
1
2
3
4
5
6
7
8
- GROUND
+ POWER
SPEAKER
SPEAKER
FIRE INPUT
BURG/FIRE INPUT
CARBON MONOXIDE INPUT
SPEAKER SUPERVISION
8
1
VOICE/SIREN
SELECTIONS
(SEETEXT)
Figure 1: 745VSD3 Voice Siren Driver Circuit Board
TERMINAL DESCRIPTIONS
Term Function Notes
1 (-) GND(-)
GROUND
INPUT
Connect to panel’s
aux power (-)
2 (+) 12VDC(+)
INPUT Connect to 12VDC (+) source on panel.
See “Fused
Method for Providing Battery
Power”on Page 3 if needed.
3
SPKR
4
SPKR
SPEAKER
TERMINALS Connect 8- , 16- , or 32-ohm
15-watt speaker. See Figure 6
for multiple speaker config-
urations.
For Listed
installations, Listed Ademco
705-820, 713, or 746-32
speakers must be used.
5 F FIRE INPUT Connect the control panel’s
output designated as the FIRE
(steady) output to this terminal
(unless this output was
connected to terminal 6).
6 B/F BURGLARY/
FIRE INPUT Connect the control’s Burglary
(steady) output to this terminal.
This terminal may also be
used to trip the Fire message
(or siren sounds) with a
Temporal Fire signal input. For
these secondary uses, no
connection to terminal 5 is
required.
7 CO CARBON
MONOXIDE
INPUT
Connect the control’s output
designated as the Carbon
Monoxide output to this
terminal.
8
SUPV SPEAKER/ WIRING
SUPERVISION
(OPTIONAL)
To supervise speaker and
associated wiring, connect to
the high (+) side of a 24-hour
zone that is activated by a
short. Disconnecting or
shorting either speaker
terminal to ground will appear
as a short on the zone. Note
that in series-connected
multiple speaker systems,
cutting any speaker will trip the
panel’s supervision zone. In
parallel-connected speaker
systems, each branch must be
cut before the control’s
supervision zone will trip.
NOTE: Check the control’s
documentation for supervision
compatibility (most Honeywell
controls are compatible.)

- 2 -
WIRING FOR BURG/FIRE INSTALLATIONS
Refer to Terminal Descriptions on Page 1, and connect
the panel bell output directly to the appropriate terminals.
1. ANNUNCIATING CO ALARM ON
VISTA P Series (21iP/20P/15P/10P, variants)
a. Hookup
To achieve proper operation for Carbon Monoxide
alarms with VISTA panels, configure the 745VSD3 for a
negative (0V) trigger by setting DIP Switch 8 to OFF.
On the panel, configure a low-going output (Trigger 17)
to alert on CO alarm. Connect 745VSD3 as shown:
234561
ON
78
SW 1
1 2 3 4 5 6 7 8
81
OUTPUTTRIGGER HARNESS
TO 12VOLT SOURCE
8-. 16-, or
32-OHM
SPEAKER
NOTE: 32-OHM SPEAKER
REQUIRED FOR ETL
LISTED INSTALLATIONS
GROUND (-)
+12V
BELL
CO
FI/B
GROUND
TOTRIGGER
VISTA 20P/15P/10P
CONTROL PANEL
745VSD3
745VSD3-002-V0
Set DIP Switch
#8 to OFF
Figure 2: VISTA P Series CO Trigger Configuration
b. Programming Trigger Output (Vista P Series)
1. Enter panel’s Program mode.
2. Select field *79
*79 Enter Output No (enter 17) *
17 OUT Norm Low? (enter 0) *
3. Enter Output No (enter 00) exits out of *79 menu.
4. Enter *80 Output Function # menu programming mode.
5. Configure the first Output function for the following:
Activated by Zone type option selection (2)
Enter Zone Type (14) Carbon Monoxide
Output Action Stay Closed selection (2)
Output Number Select (17)
6. Configure the second Output function for the following:
Activated by Zone type option selection (2)
Enter Zone Type (22) Disarm
Output Action Off selection (0)
Output Number Select (17)
7. Exit the panel’s Programming mode.
2. ANNUNCIATING CO ALARM ON
VISTA-32, -128, -250 (and variants)
a. Hookup
If using a VISTA-32, -128, -250, or other variant that
supports CO Zone Response Type 14
: Configure
7845VSD3 for a positive (+12V) trigger by setting DIP
Switch 8 to ON. On the panel, configure a relay output
(4204/4101SN)) to alert on Zone Response Type 14.
Connect 745VSD3 as shown:
234561
ON
78
SW 1
1 2 3 4 5 6 7 8
18
TO 12 VOLT SOURCE
8-. 16-, or
32-OHM
SPEAKER
NOTE: 32-OHM SPEAKER
REQUIRED FOR ETL
LISTED INSTALLATIONS
GROUND (-)
+12V
CO
FI/B
745VSD3
TB2
121110
9
87654321
(–) GROUND
(+) 12V
YEL
BLK
GRN
RED
13 14 15 16
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
COVER TAMPER (REED) SWITCH
TB1
4204
4-PIN TOUCHPAD PLUG
3
2
RELAY
1
4
RELAY CONTACTS ARE
NOT SUPERVISED
TYPICAL
(SHOWN "OFF")
C
NC
NO
C
NC
NO
C
NCNC
NO
C
NC
NO
EITHER OR BOTH
CAN BE USED
DATA IN
FROM CONTROL
DATA OUT
TO CONTROL
RELAY
RELAY
RELAY
➞
➞
➞
➞
➞
4204 CONNECTIONS
➞
Program Relay to Activate
on Zone Response Type 14 (CO)
745VSD3-003-V0
Set DIP Switch
#8 to ON
Figure 3: High End VISTA Configuration
(4204 Relay shown)
b. Programming Output (High End Vista)
Refer to the diagram above, the terminal descriptions on
Page 1, and the programming data for the panel and
selected relay/output module to configure the activation
and restore for Zone Response Type 14 (Carbon
Monoxide).
3. ANNUNCIATING CO ALARM ON ALL
OTHER PANELS
Refer to the installation documentation for the control
panel and to the “Terminal Descriptions”table on the
previous page to properly connect and configure
745VSD3.

- 3 -
OUTPUT SELECTION SWITCH SETTINGS
8-Position DIP switch SW1 is used to select Voice/Siren
outputs as well as bell/ringback and trigger options
1. Voice/Siren Outputs: SW1 Switches 1 - 4
Fire
Output Burg Output CO Output DIP Setting
1* English English English
234561
ON
78
2* English/
French English/ French English/ French
234561
ON
78
3* English/
Spanish English/ Spanish English/ Spanish
234561
ON
78
4* Eng/Span/
French Eng/Span/ French Eng/Span/ French
234561
ON
78
5* French French French
234561
ON
78
6* Spanish Spanish Spanish
234561
ON
78
7 Temporal
Fire Sweep Temporal CO
234561
ON
78
8 English Sweep English
234561
ON
78
9 English/
French Sweep English/ French
234561
ON
78
10 Temporal
Fire Eng/Span/ French Temporal CO
234561
ON
78
11 Temporal
Fire Spanish Temporal CO
234561
ON
78
12 Temporal
Fire English Temporal CO
234561
ON
78
13 English/
Spanish Sweep English/ Spanish
234561
ON
78
14 Temporal
Fire French Temporal CO
234561
ON
78
15 Eng/Span/
French Sweep Eng/Span/ French
234561
ON
78
* Most Commonly Used Settings
2. Bell, Trigger Options: SW1 Switches 5-8
SW1 switches 5 through 8 set bell test and trigger
options as shown.
234561
ON
78
BELLTEST/
RINGBACK OPTIONS
MUST BE ON FOR
LISTED INSTALLATIONS
BURG/FIRETRIGGER
ON = POSITIVE (+12V) TRIGGER
OFF = NEGATIVE (0V) TRIGGER
FIRETRIGGER
ON = POSITIVE (+12V) TRIGGER
OFF = NEGATIVE (0V) TRIGGER
CARBON MONOXIDETRIGGER
ON = POSITIVE (+12V) TRIGGER
OFF = NEGATIVE (0V) TRIGGER
745VSD3-005-V0
Figure 4. SW1 Switches 5 - 8
NOTE: If Bell Test/Ringback is selected (dip switch 5),
a fire signal will momentarily generate a warbled siren
sound for the initial portion of the siren sound and then
revert to the normal siren sound and voice message.
Configuring Multiple Speakers
Depending on the installation, 745VSD3 provides
multiple speaker configurations as shown:
745VSD3-004-V0
2 SPEAKERS
16 OHM
LOAD 4 SPEAKERS
8 OHM LOAD 8
8
8
8
8
8
4
3
4
3
Figure 5. Typical Multiple Speaker Configurations
Fused Method for Providing Battery Power
For installations requiring more power than the panel
aux power can provide (such as when using 8- or 16-
ohm speakers) you may need to obtain additional power.
You may obtain power from an external power supply, or
through a fused connection directly to the control panel
backup battery, as shown:
745x3-002-V0
VOICE
SIREN
DRIVER
CONTROL
GROUND
12V ( )
POS
( )
NEG
( )
2 AMP
IN-LINE FUSE
BATT
Figure 6. Connecting Power from the System’s Battery

- 4 -
745VSD3 SPECIFICATIONS
Physical Specifications
Measurements: 4” x 2-3/4” x 1-3/4”
Electrical Specifications
Voltage Requirements: 12-16 VDC
Current (Standby): 15mA
Speaker Specifications
Note: Use 8-ohm, 16-ohm, or 32-ohm, 15 watt speakers
8-ohm Speaker: 1400mA (max, steady siren)
16-ohm Speaker: 1050mA (max, steady siren)
32-ohm Speaker: 500mA (max, steady siren)
WARRANTY INFORMATION
For the latest warranty information, please go to:
http://www.security.honeywell.com/hsc/resources/wa/index.html
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL
PANEL THAT IS USED WITH THIS DEVICE FOR WARRANTY
INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2009 Honeywell International Inc.
www.honeywell.com/security
ÊK6210V1,Š
ÊK6210V1,ŠÊK6210V1,Š
ÊK6210V1,Š
K6210V1 2/09 Rev C