Honeywell SmartLine User manual

Honeywell Process Solutions
SmartLine Wireless Transmitter
User’s manual
34-SW-25-01
Revision 2
October 2018

iii SmartLine Wireless User's Manual Revision 2
Notices and Trademarks
Copyright 2018 by Honeywell International Inc.
Revisions 2, October 2018
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the implied
warranties of merchantability and fitness for a particular purpose and makes no express warranties except as may
be stated in its written agreement with and for its customers.
In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and
specifications in this document are subject to change without notice.
Honeywell, PlantScape, Experion PKS, and TotalPlant are registered trademarks of Honeywell International Inc.
Other brand or product names are trademarks of their respective owners.
Honeywell Process Solutions
1250 W Sam Houston Pkwy S
Houston, TX 77042

iv SmartLine Wireless User's Manual Revision 2
About This Document
This document describes preparation, operation and maintenance of the SmartLineTM Wireless Pressure
Transmitters. Mounting, installation and wiring are covered in other documents.
Honeywell does not recommend using devices for critical control where there is a single point of failure
or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop
control, supervisory control, and controls that do not have environmental or safety consequences. As
with any process control solution, the end-user must weigh the risks and benefits to determine if the
products used are the right match for the application based on security, safety, and performance.
Additionally, it is up to the end-user to ensure that the control strategy sheds to a safe operating condition
if any crucial segment of the control solution fails.
Revision Information
Document Name
SmartLine Wireless User's Manual
Document ID
(This document)
Revision
Number
Publication Date
1st Release
34-SW-25-01
1
September 2018
RoHS added
34-SW-25-01
2
October 2018
References
The following list identifies all documents that may be sources of reference for material discussed in this
publication.
Document Title
Doc #
STDW800 Wireless Specification, Differential Transmitter
34-SW-03-01
STAW800 Wireless Specification, Absolute Transmitter
34-SW-03-02
STGW800 Wireless Specification, Gauge Transmitter
34-SW-03-03
STFW700_800 Wireless Specification, Flanged Transmitter
34-SW-03-04
STRW700_800 Wireless Specification, Remote Seal Transmitter
34-SW-03-05
STDW700 Wireless Specification, Differential Transmitter
34-SW-03-06
STAW700 Wireless Specification, Absolute Transmitter
34-SW-03-07
STGW700 Wireless Specification, Gauge Transmitter
34-SW-03-08
OneWireless R310 Release Notes
OWDOC-X252-en-310A
OneWireless R310 Migration Users Guide
OWDOC-X258-en-310
OneWireless R310 Field Device Access Point Users Guide
OWDOC-X256-en-310
OneWireless R310 Wireless Device Manager Users Guide
OWDOC-X254-en-310
OneWireless R300 Experion PKS Integration Guide
OWDOC-X259-en-300
OneWireless R300 Wireless LAN Controller Configuration Guide
OWDOC-X255-en-300
OneWireless R300 Network Planning an Installation Guide
OWDOC-X253-en-300

Revision 2 SmartLine Wireles User's Manual v
Support and Contact Information
For Europe, Asia Pacific, North and South America contact details, refer to the back page of this
manual or the appropriate Honeywell Support web site:
Honeywell Corporate www.honeywell.com
Honeywell Process Solutions https://www.honeywellprocess.com/*
Training Classes https://www.honeywellprocess.com/en-US/training
Telephone and Email Contacts
Area
Organization
Phone Number
United States and
Canada
Honeywell Inc.
1-800-343-0228 Customer Service
1-800-423-9883 Global Technical Support
Global Email
Support
Honeywell Process Solutions
[e-mail]

vi SmartLine Wireless User's Manual Revision 2
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol
Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a task.
CAUTION
Indicates a situation which, if not avoided, may result in equipment or work (data) on
the system being damaged or lost, or may result in the inability to properly operate
the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury. It may also be used to alert against unsafe
practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in serious injury or death.
WARNING symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in the
manual.
WARNING, Risk of electrical shock: Potential shock hazard where HAZARDOUS
LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC may be accessible.
ESD HAZARD: Danger of an electro-static discharge to which equipment may be
sensitive. Observe precautions for handling electrostatic sensitive devices.
Protective Earth (PE) terminal: Provided for connection of the protective earth
(green or green/yellow) supply system conductor.
Functional earth terminal: Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to Protective Earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground:Functional earth connection. NOTE: This connection shall be
bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.
Chassis Ground: Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.
continued

Revision 2 SmartLine Wireles User's Manual vii
Symbol
Description
The Factory Mutual®Approval mark means the equipment has
been rigorously tested and certified to FM standards for safety
and/or performance.
The Canadian Standards mark means the equipment has been
tested and meets applicable standards for safety and/or
performance.
The Ex mark means the equipment complies with the requirements
of the European standards that are harmonized with the 94/9/EC
Directive (ATEX Directive, named after the French "ATmosphere
EXplosible").
For radio equipment used in the European Union in accordance
with the Radio Equipment Directive (RED) and the CE Mark. The
alert sign must be used when a restriction on use (output power
limit by a country at certain frequencies) applies to the equipment
and must follow the CE marking.
The C-Tick mark is a certification trade mark registered to ACMA
(Australian Communications and Media Authority) in Australia under
the Trade Marks Act 1995 and to RSM in New Zealand under
section 47 of the NZ Trade Marks Act. The mark is only to be used
in accordance with conditions laid down by ACMA and RSM. This
mark is equal to the CE Mark used in the European Union.
N314 directly under the logo is Honeywell’s unique supplier
identification number.
The ISA100 Wireless Compliant logo indicates the device has
received ISA100.11a conformance certification and is registered
with the Wireless Compliance Institute, assuring device
interoperability.
CRN
Canadian Registration Number

ix SmartLine Wireless User's Manual Revision 2
Contents
Honeywell Process Solutions................................................................................................................iii
Symbol Definitions..................................................................................................................................vi
1. INTRODUCTION....................................................................................................1
1.1 Purpose..........................................................................................................................................1
1.2 Scope..............................................................................................................................................1
1.3 OneWireless network overview ...................................................................................................1
1.4 Security Considerations...............................................................................................................1
1.5 Licensing and License Keys for Anti-Aliasing Filter.................................................................1
1.6 About the transmitter....................................................................................................................2
1.7 Physical Characteristics...............................................................................................................4
2. PREPARATION AND QUICK START ...................................................................6
2.1 Introduction ...................................................................................................................................6
2.2 Set up the Network........................................................................................................................6
2.3 Transmitter Quick Start ................................................................................................................6
3. INSTALLATION .....................................................................................................8
3.1 Installation Site Evaluation ..........................................................................................................8
3.2 Maximum Working Pressure:.......................................................................................................8
3.3 Environmental Conditions: ..........................................................................................................8
3.4 Transmitter Weights and Dimensions.........................................................................................9
Weights ..................................................................................................................................................................9
Dimensions...........................................................................................................................................................10
3.5 Installation drawing number tables...........................................................................................14
3.6 Conduit / Cable Entries...............................................................................................................15
Summary..............................................................................................................................................................15
3.7 Mounting Summary.....................................................................................................................16
3.8 Piping the SmartLine Wireless Transmitter .............................................................................23
3.9 Rotate transmitter housing ........................................................................................................27
3.10 Rotate display ..........................................................................................................................27
Tools required ......................................................................................................................................................27
Procedure.............................................................................................................................................................27
Display adjustment...............................................................................................................................................28
3.11 Antenna adjustment and mounting.......................................................................................29
Requirements.......................................................................................................................................................29
Integral antenna ...................................................................................................................................................29

Contents
Telephone and Email Contacts
x SmartLine Wireless User's Manual Revision 2
3.12 Remote antenna.......................................................................................................................31
Outdoor installation warnings...............................................................................................................................31
Choosing a Mounting Location.............................................................................................................................32
Site Selection.......................................................................................................................................................32
Mounting the Antenna..........................................................................................................................................33
Directional mounting procedure ...........................................................................................................................34
Omnidirectional mounting procedure ...................................................................................................................35
Grounding the antenna ........................................................................................................................................36
4. START UP ...........................................................................................................38
4.1 Battery Power Option..................................................................................................................38
Install/Replace batteries.......................................................................................................................................38
Battery Pack installation and replacement procedure..........................................................................................40
Battery Pack Test Terminals................................................................................................................................40
4.2 24V Power Supply Option ..........................................................................................................41
24V Power Supply ...............................................................................................................................................42
24V Power Supply Connection/Replacement Procedure.....................................................................................43
4.3 Grounding....................................................................................................................................44
24V dc Power Supply Option (DC) System Diagram ...........................................................................................44
4.4 Display sequence........................................................................................................................45
4.5 Provisioning.................................................................................................................................45
4.6 Calibrating the transmitter .........................................................................................................46
Overview..............................................................................................................................................................46
Calibrate zero.......................................................................................................................................................46
Procedure for field calibration of Honeywell compound characterized SmartLine Wireless Transmitters............47
5. FUNCTION BLOCKS...........................................................................................50
5.1 Introduction .................................................................................................................................50
5.2 Block description ........................................................................................................................50
Block types...........................................................................................................................................................50
Block diagram......................................................................................................................................................50
6. OPERATION........................................................................................................51
6.1 Overview ......................................................................................................................................51
Display modes .....................................................................................................................................................51
6.2 Transmitter connection status...................................................................................................52
6.3 Transmitter PV display ...............................................................................................................54
PV status..............................................................................................................................................................57
6.4 Provisioning Device menus .......................................................................................................60
Overview..............................................................................................................................................................60
Main menu...........................................................................................................................................................60
Security and Node Deployment ...........................................................................................................................60
De-provisioning....................................................................................................................................................62
Read Device Information......................................................................................................................................62
Advanced Options................................................................................................................................................64