Horizon Fitness Elite T3000 User manual

TREADMILL OWNER’S MANUAL
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Elite T3000
Elite T4000

23
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage
to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
WARNING
SERIAL NUMBER:
MODEL NAME: HoRIzoN TREADMILL

4 5
CONSOLE
ON/OFF SWITCH
CIRCUIT BRE AKER
POWER CORD
CONSOLE CONTROL S AND DISPL AY WINDOWS
USB PORT AND AU DIO IN JACK
SAFE TY KE Y PL ACEMENT
ROLLER END CAP
RE AR ROLLER TENSION/ADJ USTMENT BOLTS
SPEAKERS
WATE R BOTTLE HOLDER
GRIP PULSE HANDR AILS
DROP -DOWN HANDLEBAR
TRANSPORT WHEEL
RE ADING RACK / AUDIO CORD CHANNEL
HANDLEBARS
MOTOR COVER
SIDE R AIL
CONSOLE MAST
RUNNING BELT / RUNNING DECK
TooLS INCLUDED:
F8 mm T-Wrench
F5 mm T-Wrench
F5 mm L-Wrench
FScrewdriver
PARTS INCLUDED:
F1 Console Assembly
F2 Console Masts
F1 Hardware Kit
F1 Safety Key
F1 Power Cord
F1 Audio Adapter Cable
If you have questions or if
there are any missing parts,
contact your local dealer.
NEED HELP?
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled. Unpack and assemble the unit
where it will be used. Never grab hold of any portion of the incline frame and attempt to
lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
( T4000 )
PRE ASSEMBLY
T4000
SHOWN

6 7
HARDWARE foR STEP 1-1 :
ASSEMBLY STEP 1-1 (T3000 ONLY) ASSEMBLY STEP 1-1 (T3000 ONLY)
T3000
ONLY
T3000
ONLY
BOLTS (A)
SPRI NG WASHERS (B)
ARC WASHERS (C)
MAIN FRAME B RACKET
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
LEFT CONSOLE MAST
BOLT (A)
M8x20 mm
Qty: 6
SPRI NG WASHER (B)
8.2 mm
Qty: 6
ARC WASHER (C)
Φ8.2xΦ17 mm
Qty: 6
SCREW (D)
Φ4x20 mm
Qty: 4
* This step is for T3000 models only.
A Cut the yellow banding straps and lift the running
deck upward to remove all contents from underneath
the running deck.
B Open HARDWARE FOR STEP 1.
C Slide MAIN FRAME BOOT up CONSOLE MAST.
Pull LEAD WIRE through RIGHT CONSOLE MAST.
After pulling the LEAD WIRE through the mast, the
top of the CONSOLE CABLE should be located at
the top of the mast. Detach and discard LEAD WIRE.
D Place RIGHT CONSOLE MAST over MAIN FRAME
BRACKET.
E Attach CONSOLE MAST to MAIN FRAME
BRACKET using 3 BOLTS (A), 3 SPRING
WASHERS (B) and 3 ARC WASHERS (C).
NOTE: Do not pinch console cable when placing
the mast onto the main frame bracket.
SCREW (D)
MAIN FRAM BOOT
F Slide MAIN FRAME BOOT down over MAIN FRAME
BRACKET.
G Repeat steps D–F on other side.
H Attach MAIN FRAME BOOTS to main frame using 4
SCREWS (D).
(T3000)
(T3000)

8 9
ASSEMBLY STEP 1-2 (T4000 ONLY)ASSEMBLY STEP 1-2 (T4000 ONLY)
HARDWARE foR STEP 1-2 :
T4000
ONLY
T4000
ONLY
SCREW (D-1)
SCREW (D)
MAIN FRAM BOOT
MAIN FRAM
BOLTS (A)
SPRI NG WASHERS (B)
ARC WASHERS (C)
MAIN FRAME B RACKET
RIGHT CONSOLE MAST
LEAD WIRE
CONSOLE CABLE
LEFT CONSOLE MAST
E Pull LEAD WIRE through RIGHT CONSOLE MAST.
After pulling the LEAD WIRE through the mast, the
top of the CONSOLE CABLE should be located at
the top of the mast. Detach and discard LEAD WIRE.
F Place RIGHT CONSOLE MAST over MAIN FRAME
BRACKET.
G Attach CONSOLE MAST to MAIN FRAME
BRACKET using 3 BOLTS (A), 3 SPRING
WASHERS (B) and 3 ARC WASHERS (C).
H Repeat steps F–G on other side.
NOTE: Do not tighten bolts until step 3 is complete.
NOTE: Do not pinch console cable when placing
the mast onto the main frame bracket.
* This step is for T4000 models only.
A Cut the yellow banding straps and lift the running
deck upward to remove all contents from underneath
the running deck.
B Open HARDWARE FOR STEP 1.
C Place MAIN FRAME BOOTS over MAIN FRAME as
shown.
D Attach MAIN FRAME BOOTS to MAIN FRAME
using 6 SCREWS (D & D-1).
(T4000)
(T4000)
BOLT (A)
M8x20 mm
Qty: 6
SPRI NG WASHE R (B)
8.2 mm
Qty: 6
ARC WASHER (C)
Φ8.2xΦ17 mm
Qty: 6
SCREW (D-1)
Φ4x20 mm
Qty: 2
SCREW (D)
M4 x 12
Qty: 4

10 11
A Open HARDWARE FOR STEP 2.
B CONNECT HANDLEBAR CABLES, and slide
HANDLEBARS into CENTER BAR.
C Attach HANDLEBARS to CENTER BAR using 4
BOLTS (E), 4 SPRING WASHERS (F) and 4 ARC
WASHERS (G).
NOTE: Do not pinch wires while attaching the
handlebars. Please do not tighten the screws of
handlebar, tighten them when assembly process
is completed.
ASSEMBLY STEP 2 ASSEMBLY STEP 3
ALL
MoDELS
HARDWARE foR STEP 3HARDWARE foR STEP 2
BOLT (E)
M6 x 10 mm
Qty: 4
SPRING WASHER (F)
6.2 mm
Qty: 4
ARC WASHER (G)
Φ6.2 x Φ14
Qty: 4
CONSOLE CABLES
HANDLEBARS
CENTER BAR
BOLTS (E)
SPRING WASHERS (F)
ARC WASHERS (G)
ALL
MoDELS
FLAT WASHERS (I)
CONSOLE MAST CAP
SPRING WASHERS (B)
BOLTS (J)
CONSOLE (upside down)
A Open HARDWARE FOR STEP 3.
B With the CONSOLE upside down, attach the
CONSOLE MAST CAPS to the CONSOLE
using 6 BOLTS (J) , 6 SPRING WASHERS
(B) and 6 FLAT WASHERS (I).
BOLT (J)
M8x20 mm
Qty: 6
FLAT WASHE R (I)
Φ8.2x16 mm
Qty: 6
SPRI NG WASHE R (B)
8.2 mm
Qty: 6

12 13
ASSEMBLY STEP 4
HARDWARE foR STEP 4 :
ALL
MoDELS
BOLTS (J)
SPRI NG WASHE RS (B)
ARC WASHERS (C)
CONSOLE MAST
CONSOLE MAST CAP
CONSOLE
ASSEMBLE
THIS SIDE
FIRST
CONSOLE CABLES
A Open HARDWARE FOR STEP 4.
B Gently place the CONSOLE on top of the
CONSOLE MASTS. Attach the LEFT SIDE first
using 3 BOLTS (J), 3 SPRING WASHERS (B)
and 3 ARC WASHERS (C).
C Connect the CONSOLE CABLES, carefully
tucking wires in masts to avoid damage.
D Attach the RIGHT SIDE of the CONSOLE
using 3 BOLTS (J), 3 SPRING WASHERS (B)
and 3 ARC WASHERS (C).
NOTE: Be careful not to pinch any wires while
assembling.
NOTE: Be careful not to pinch any wires while
assembling.
BOLT (J)
M8 x 20mm
Qty: 6
ARC WASHER (C)
Φ8.2 x Φ16
Qty: 6
SPRI NG WASHE R (B)
8.2 mm
Qty: 6
ASSEMBLY STEP 5
A Attach CONSOLE CABLES from HANDLEBARS
to CONSOLE CABLES from CONSOLE. Gently
tuck excess cable into CONSOLE before sliding the
HANDLEBARS onto CONSOLE.
B Attach HANDLEBARS to CONSOLE using 6
BOLTS (H), 6 SPRING WASHERS (B) and 6 FLAT
WAHSERS (I).
ALL
MoDELS
HARDWARE foR STEP 5
BOLT (H)
M8 x 12 mm
Qty: 6
FLAT WAS HER (I)
Φ8.2 x Φ16
Qty: 6
SPRI NG WASHER (B)
8.2 mm
Qty: 6
FLAT WAS HERS (I)
SPRI NG WASHERS (B)
BOLTS (H)
HANDLE BARS
CONSOLE

14 15
BOLTS (K)
(T3000)
ASSEMBLY STEP 6-1 (T3000 ONLY)
A Open HARDWARE FOR STEP 6.
B Attach LEFT and RIGHT DROP DOWN
HANDLEBAR to the LONG HANDLEBAR and
BASE FRAME by using 6 BOLTS(K).
T4000
ONLY
HARDWARE foR STEP 6-1
BOLT (K)
M6 x 12mm
Qty: 6
ASSEMBLY STEP 6-2(T4000 ONLY)
T3000
oNLY
A Open HARDWARE FOR STEP 6.
B Attach LEFT and RIGHT DROP DOWN
HANDLEBAR to the LONG HANDLEBAR and
BASE FRAME by using 6 BOLTS(K).
C Carefully slide the DROP DOWN HANDLEBAR
COVER and fix to the BASE FRAME using 4
SCREWS(L).
(T4000)
HARDWARE foR STEP 6-2 :
SCREW (D)
M 4 x 12
Qty: 4
BOLT (K)
M6 x 12mm
Qty: 6
BOLTS(K)
SCREWS(D)

16
ASSEMBLY STEP 7
YOU ARE FINISHED!
Elite T3000
Max. User Weight: 160 kg / 350 lbs
Product Weight: 122kg / 268lbs
Overall Dimension: 205 x 93.5 x 145 cm / 673” x 307” x 476”
Elite T4000
Max. User Weight: 170 kg/ 375 lbs
Product Weight:130kg / 286 lbs
Overall Dimension: 215 x 93.5 x 145 cm / 705” x 307” x 476”
(T4000)
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
TREADMILL GUIDE has instructions for the following:
• LoCATIoN of THE TREADMILL
• USING THE SAfETY KEY
• foLDING THE TREADMILL
• MoVING THE TREADMILL
• LEVELING THE TREADMILL
• TENSIoNING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• USING THE HEART RATE fUNCTIoN
T4000
SHOWN

18 19
7 8 9
4 5 6
1 2 3
0
S T O P
HOL D TO R ES E T
S TA R T
QUI C K S TA R T
Confirm
Bestätigen Conf irm Bestätigen
SCHNELLSTART FÜR NULLSTELLUNG GE DRÜCKT H ALTEN
PROGRAMS
PROGRAMME
Manual Manuell
Intervals Intervall
Peak Intervals Hohe Intervalle
Stamina Builder Ausdauer
Weight Loss Gewichtsreduzier ung
Golf Course Golfparcours
Foot Hills Berggehen
Mountain Climb Bergsteigen
HR Intervals HR Intervall
THR Zone Zielherzfrequenz
Custom 1 Benutzer 1
Custom 2 Benutzer 2
1
2
3
4
5
6
7
8
9
10
11
12
AD C B T E O
HF S P LG K M JI
N
R R
QN
(T4000)
CoNSoLE oPERATIoN
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed
before use.
A) LED DISPLAY WINDoWS: time, incline, distance, speed, date and clock.
B) ALPHANUMERIC DISPLAY WINDoW: calories, heart rate, pace and PROFILE™ display information.
C) DoT MATRIx DISPLAY WINDoW: displays workout level and progress.
D) PRofILE™ BUTToN: used to scroll through PROFILE™ display modes. Must be pressed after
selecting user.
E) CHANGE DISPLAY BUTToN: used to scroll through display modes. Press to change display
feedback during workout.
f) START: press to begin exercising, start your workout, or resume exercising after pause.
G) SToP: press to pause/end your workout. Hold for 3 seconds to reset the console.
H) PRoGRAMMING BUTToN: used to select program, level and time, and other options.
I) INCLINE KEYS: used to adjust incline in small increments (0.5% Increments).
J) SPEED KEYS: used to adjust speed in small increments (0.1 KMH increments).
K) QUICK ADJUST KEYPAD: used to reach desired speed or incline more quickly.
L) CoNfIRM INCLINE: used to change incline to level entered into keypad.
M) CoNfIRM SPEED: used to change speed to level entered into keypad.
N) SPEAKERS: music plays through speakers when your media player is connected to the console.
o) AUDIo IN JACK / USB PoRT: plug your media player into the console using the included audio
adaptor cable. USB port is used for software updates.
P) AUDIo oUT / HEADPHoNE JACK: plug your headphones into this jack to listen to your music
through the headphones. Note: when headphones are plugged into the headphone jack the sound
will no longer come out through the speakers.
Q) READING RACK / MEDIA PLAYER HoLDER: holds reading material or your media player.
R) WATER BoTTLE PoCKETS: holds personal workout equipment.
S) SAfETY KEY PoSITIoN: enables treadmill when safety key is inserted.
T) ENERGY SAVER : To minimize energy consumption, your machine will enter energy saver mode automatically (after entering stand-by mode
for 10 mins) and could be quickly waken up with a touch of a button.
QUICK ADJUST KEYPAD (K)
Quickly access any speed or incline
level by typing the number and
pressing CONFIRM SPEED (M)
or CONFIRM INCLINE(L) keys.
Examples:
• To change the speed to 10 KMH,
press 1-0-0-CONFIRM SPEED.
• To change the incline to 10%,
press 1–0–0–SET INCLINE
(NOTE: If there is no decimal point,
you still must enter 0).
7 8 9
4 5 6
1 2 3
0
Confir m
Bestä tigen Conf irm Bestä tigen
T4000
SHOWN