Horizon Fitness T100 User manual

T100
TREADMILL OWNER’S MANUAL
MANUEL DU PROPRIÉTAIRE DU TAPIS ROULANT
MANUAL DEL PROPIETARIO DE LA CAMINADORA
Read the TREADMILL GUIDE before using this OWNER’S MANUAL.
Lire le GUIDE D’UTILISATION DU TAPIS ROULANT avant de se servir du présent MANUEL DU PROPRIÉTAIRE.
Lea la GUÍA DEL USUARIO DE LA CAMINADORA antes de usar este MANUAL DEL PROPIETARIO.

2
3 ENGLISH
22 FRANÇAIS
42 ESPAÑOL

3
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the
treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located near the on/off
power switch and power cord and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
SERIAL NUMBER:
MODEL NAME: HORIZON T100 TREADMILL
WARNING

4
GRIP PULSE HANDRAILS
ON/OFF SWITCH
CIRCUIT BREAKER
TRANSPORT WHEEL
FRAME EXTENSION TUBE
CUSHIONING
POWER CORD
READING RACK
TOUCH PAD PANEL
ATTACH SAFETY KEY CLIP TO CLOTHING BEFORE STARTING. TO
AVOID INJURY, STAND ON THE SIDE RAILS BEFORE STARTING
TREADMILL. READ AND FOLLOW ALL INSTRUCTIONS BEFORE
OPERATING. KEEP CHILDREN AWAY FROM THIS EQUIPMENT.
REMOVE SAFETY KEY WHEN NOT IN USE AND STORE OUT OF
REACH OF CHILDREN. CONSULT A PHYSICIAN BEFORE USING
THIS EQUIPMENT. STOP EXERCISING IF YOU FEEL PAIN, FAINT,
DIZZY OR SHORT OF BREATH. FOR CONSUMER USE ONLY.
WARNING
WATER BOTTLE HOLDER
CONSOLE
SAFETY KEY PLACEMENT
RUNNING BELT / RUNNING DECK
SIDE RAIL
ROLLER END CAP
CONSOLE MAST
HANDLEBARS
REAR ROLLER
ADJUSTMENT BOLTS
MOTOR COVER
DECK LOCK PIN
SUJETE LA LLAVE DE SEGURIDAD A SU ROPA ANTES DE COMENZAR. PARA EVITAR
LESIONES PÁRESE EN LO RIELES LATERALES ANTES DE PONER A FUNCIONAR LA
CAMINADORA. LEA Y SIGA LAS INSTRUCCIONES ANTES DE USAR ESTA
CAMINADORA. NO DEJE QUE LOS NIÑOS SE ACERQUEN A ESTE EQUIPO. CUANDO
NO LA ESTÉ USANDO, SAQUE LA LLAVE DE SEGURIDAD Y GUÁRDELA FUERA DEL
ALCANZE DE LOS NIÑOS. CONSULTE A UN MÉDICO ANTES DE USAR ESTE EQUIPO.
DEJE DE HACER EJERCICIO SI SIENTE DOLOR, DESMAYO, MAREO O SI LE FALTA EL
ALIENTO. ESTE EQUIPO ES SÓLO PARA EL USO DEL CONSUMIDOR.
ATTACHER LA PINCE DE LA CLÉ DE SÉCURITÉ AUX VÊTEMENTS AVANT DE METTRE L’APPAREIL
EN MARCHE. POUR ÉVITER TOUTE BLESSURE, METTRE LES PIEDS SUR LES RAILS LATÉRAUX
AVANT DE LANCER LE TAPIS ROULANT. LIRE ET SUIVRE TOUTES LES INSTRUCTIONS AVANT LA
MISE EN MARCHE. TENIR LES ENFANTS ÉLOIGNÉS DE L’APPAREIL. RETIRER LA CLÉ DE
SÉCURITÉ LORSQUE L’APPAREIL N’EST PAS UTILISÉ ET LA CONSERVER HORS DE PORTÉE DES
ENFANTS. CONSULTER UN MÉDECIN AVANT D’UTILISER CET APPAREIL. EN CAS DE
DOULEURS, DE NAUSÉES, DE VERTIGES OU D’ESSOUFFLEMENTS, ARRÊTER IMMÉDIATEMENT
TOUT EXERCICE. À L’USAGE DU CLIENT SEULEMENT.
ADVERTENCIA
AVERTISSEMENT
CAUTION ATTENTION PRECAUCIÓN
KEEP HANDS AND FEET
AWAY FROM THIS AREA.
GARDER LES MAINS ET LES
PIEDS LOIN DE CETTE REGION.
MANTENGA LAS MANOS Y LOS
PIES LEJOS DE ESTA ÁREA.
CAUTION ATTENTION PRECAUCIÓN
HOLD ONTO DECK WHEN
LATCH IS RELEASED.
TENIR LA PLATE-FORME LORSQUE LA
GOUPILLE DE VERROUILLAGE EST RETIRÉE.
SUJETE LA PLATAFORMA
CUANDO VAYA BAJANDO.

5
TOOLS INCLUDED:
F5 mm Allen Wrench
F6 mm T-Wrench
FScrewdriver
PARTS INCLUDED:
F1 Safety Key
F2 Frame Extension Tubes
F1 Console Assembly
F2 Console Masts
F1 Water Bottle Holder
F2 Hand Grips
F1 Deck Lock Pin
F2 End Caps
F6 Hardware Bags
F1 Bottle of Silicone Lubricant
(for 2 applications)
If you have questions or if
there are any missing parts,
contact Customer Tech
Support. Contact information
is located on the back panel
of this manual.
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. Never grab
hold of any portion of the incline frame and attempt to lift or move the treadmill.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
WARNING
NEED HELP?
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
PRE ASSEMBLY

6
ASSEMBLY STEP 1
A Open HARDWARE BAG 1.
B Slide the left FRAME EXTENSION TUBE onto
the CONSOLE MAST SUPPORT TUBE. Bolt
in place using 2 SCREWS (A) on the side.
C Repeat on the other side.
SCREW (A)
15 mm
Qty: 4
HARDWARE BAG 1 CONTENTS :
FRAME EXTENSION TUBE
CONSOLE MAST SUPPORT TUBE
SCREWS (A)

7
ASSEMBLY STEP 2
A Open HARDWARE BAG 2.
B Slide the LEFT CONSOLE MAST
down onto the CONSOLE MAST
SUPPORT TUBE. Bolt in place
using 2 BOLTS (B),2SPRING
WASHERS (C), and 2 FLAT
WASHERS (D) on the side. Then,
bolt in place using 2 BOLTS (B), 2
SPRING WASHERS (C), and 2 ARC
WASHERS (E) on the front.
C Repeat on the other side.
On RIGHT CONSOLE MAST, the
CONSOLE CABLE must be threaded
through the mast.
BOLT (B)
15 mm
Qty: 8
SPRING WASHER (C)
15 mm
Qty: 8
FLAT WASHER (D)
15 mm
Qty: 4
ARC WASHER (E)
17 mm
Qty: 4
HARDWARE BAG 2 CONTENTS :
RIGHT CONSOLE MAST
CONSOLE MAST
SUPPORT TUBE
BOLT (B)
SPRING WASHER (C)
FLAT WASHER (D)
BOLT (B)
SPRING WASHER (C)
ARC WASHER (E)
CONSOLE CABLE
(THREAD THROUGH
TOP OF CONSOLE MAST)
NOTE: Do not completely tighten any
screws or bolts until STEP 4 is complete!
NOTE: Be careful not to pinch any wires
while assembling the masts.

8
ASSEMBLY STEP 3
BOLT (B)
15 mm
Qty: 6
SPRING WASHER (C)
15 mm
Qty: 4
FLAT WASHER (D)
15 mm
Qty: 4
ARC WASHER (F)
18 mm
Qty: 2
HARDWARE BAG 3 CONTENTS :
CONSOLE CABLE
(THREAD THROUGH HOLE
IN RIGHT HAND GRIP)
BOLTS (B)
SPRING WASHERS (C)
FLAT WASHERS (D)
BOLTS (B)
ARC WASHERS (F)
CONSOLE MAST
HAND GRIP
A Open HARDWARE BAG 3.
B Insert LEFT HAND GRIP onto upright
CONSOLE MAST.
C Attach the LEFT HAND GRIP to the CONSOLE
MAST using 2 BOLTS (B), 2 SPRING
WASHERS (C) and 2 FLAT WASHERS (D)
from the inside and 1 BOLT (B) and 1 ARC
WASHER (F) from the front.
D Carefully thread the CONSOLE CABLE through
the hole in the RIGHT HAND GRIP.
E Attach the RIGHT HAND GRIP as explained
above in STEPS B–C.
NOTE: Do not completely tighten any
screws or bolts until STEP 4 is complete!
NOTE: Be careful not to pinch any wires
while assembling the masts.

9
ASSEMBLY STEP 4
A Open HARDWARE BAG 4.
B Slide the CONSOLE onto the HAND GRIP POSTS.
C Attach the HAND GRIP POSTS to the CONSOLE
using 4 SCREWS (G) and 4 ARC WASHERS (H)
from the below the CONSOLE.
D Connect the CONSOLE CABLES and carefully tuck
wires in mast to avoid damage. Note: do not pinch
console cable. Be sure the console cable prongs
are aligned and the ends are tightly seated into each
other.
E Attach CONSOLE CABLE COVER.
F Go back and completely tighten all bolts and screws
from STEPS 1-4.
SCREW (G)
10 mm
Qty: 4
ARC WASHER (H)
12 mm
Qty: 4
HARDWARE BAG 4 CONTENTS :
SCREWS (G)
ARC WASHERS (H)
CONSOLE
HAND GRIP POST
CONSOLE
UPRIGHT MAST
CONSOLE CABLE
CONSOLE CABLE
COVER
NOTE: Be careful not to pinch any wires
while attaching the console.

10
ASSEMBLY STEP 5
A Open HARDWARE BAG 5.
B Attach DECK LOCK PIN to the LEFT
CONSOLE MAST using 2 SCREWS (I).
C Insert CUP HOLDER into right console pocket.
SCREW (I)
15 mm
Qty: 2
HARDWARE BAG 5 CONTENTS :
LEFT CONSOLE MAST
CUP HOLDER
CONSOLE
DECK LOCK PIN
SCREWS (I)