human care Fellow Classic User manual

Accessory manual
Fellow Classic, Fellow Supreme

2
www.humancaregroup.com
Content
Accessory overview 3
Assembly Tray 4
Assembly Basket 5
Assembly Slow Down Brake 5
Assembly Newspaper Strap 5
Assembly cane holder 6
Assembly Bag 7
Assembly Back Support 7
Assembly Curb Climber 8
Assembly IV-stand 8
Assembly Oxygen Holder 10
Assembly One Hand Brake 11
Tillbehörsöversikt 12
Montering bricka 13
Montering korg 14
Montering släpbroms 14
Montering käpphållare 15
Montering väska 16
Montering ryggband 16
Montering steghjälp 17
Montering droppställning 17
Montering tidningsband 19
Montering Syrgashållare 20
Montering enhandsbroms 20
Montering låsspärr 21

www.humancaregroup.com
3
Accessory Manual (ENG)
Fellow Classic, Fellow Supreme
Accessory overview
Tray
Practical for resting items.
Part no, Fellow Classic: 08806
(image 1)
Part no. Fellow Supreme: 10667
(Image 2)
Basket with handle
Basket ideal for shopping.
Part no, Fellow Classic standard:
08805. Fellow Classic low: 88052.
Fellow Classic narrow, wide and
high: 88052. (Image 1)
Part no Fellow Supreme: 10666
(Image 2)
Slow down brake
Prevents the rollator from moving
too fast. Part no: 10625 (set)
Cane holder
Simplifies the transportation of a
cane. Part no: 10603
Soft carry case ideal for personal
items.
Part no: 08808. (Cannot be used on
Fellow Classic low)
Back rest
Gives support for the back when
sitting.
Part no: 10668
Curb climber
Simplifies the transport over
obstacles. Integrated in rollator for
Fellow Supreme.
Part no (Fellow Classic):10661
IV-stand
Can only be used with Fellow
Classic.
Part no: 89654
Oxygen holder
Part no, Fellow Classic: 08811.
Part no. Fellow Supreme: 10671
Newspaper strap
Can only be used on Fellow
Supreme.
Part no. 10679.
One-hand brake
Allows control of brakes with one
hand. Part no, Fellow Classic, right:
10677, left: 10678. Part no. Fellow
Supreme, right: 10669, left: 10676.
1
2
1
2

4
www.humancaregroup.com
Attaching the Tray ENG
Fellow Classic
1. Attach the bracket of the tray over the back
edge of the seat.
2. Secure the tray by firmly pressing it over the
front edge of the seat.
Lift the tray in the front edge when removing it.
1.
2.
Fellow Supreme
Assemble the tray on to the seat of the rollator
as according to picture below.
1. Remove the tray by unfolding the seat.
Push underneath the tray’s feet to remove the
tray from the seat.

www.humancaregroup.com
5
Attaching the Basket ENG
Fellow Classic
Hang the basket on the pipe to the locking device
and place it on the grating. Max load 10kg.
Fellow Supreme
Place the basket on the grid and push the
bracket over the frame.
Slow down brake - right and left
The trailer brake is assembled by pushing it onto
the brake gear and fasten it through leading the
hook on the underside of the brake gear.
Adjust the roll resistance by screwing the
adjusting screw. Lock the adjusting screw with
the stop nut.
Attaching the Slow Down Brake ENG
Attaching the Newspaper Strap ENG
Pull the news paper strap over the seat to the
intended track. Only for Fellow Surpreme

6
www.humancaregroup.com
Assembly cane holder
Assembling upper part.
The cane holder is delivered in two main parts, an
upper and a lower. These are in turn composed of
two parts, verify that you have received them.
1. Open the clamp about that much it can be lead
over the handle pipe.
2. Before closing the clamp, take the attachment
and lead the pliers of the clamp through the
hole of the attachment. Attend on turning it in
preferred position.
3. Close the clamp and tighten the screw. Note!
Make sure that the attachment is secured.
Assembling lower part.
1. Open the clamp about that much it can be lead
over the handle pipe.
2. Before closing the clamp, take the cup and
lead the pliers of the clamp through the hole of
the attachment. Attend on turning it in preferred
position.
3. Close the clamp and tighten the screw. Note!
Make sure that the cup is secured.
ENG

www.humancaregroup.com
7
Attaching the Bag ENG
Form adjusted carrier bag that should be
adjusted around the pipe at the hold of the seat.
Assembly Back Support ENG
1. Loosen the screws and remove the knobs on
both sides.
2. Insert the back support into the end of the
handle.
3. Tighten the screws and the back support is
assembled.
The rollator can NOT be suspended,
carried or lifted in the back support.
Make sure the back support is securely
fastened. Pull the back support to make sure
it is fastened properly. NOTE! Pay aenon to
cracks or loose parts.

8
www.humancaregroup.com
Assembly Curb Climber ENG
8-10 mm
Assembly IV-stand ENG
Product descripon
The drip stand consist of following parts:
• Clamps, 3 pc
• Bottom support
• Pipe (lower) - including lock housing,
screws and handle
• Bended side pipes (right, left)
• Pipe (upper) with holder for drip -
including velcro.
• Counterweigth
• Bundle straps for counterweight, 2 pc.
• Allen key 5 mm.
Only for Fellow Classic
The heigth is
adjusted by
loosening this
screw, heightening
or lowering the
upper part, and
tightening the
screw.
The IV bag/bottle
is to be hanged
here.
Only for Fellow Classic

www.humancaregroup.com
9
8-10 mm
Important for technicians, prescribers and
users to know
• Rollator with IV stand must only be used on
a plane level.
• Point the hooks on the IV stand towards the
middle of the rollator to avoid skew load.
• Maximum load on the IV stand is 3 kg.
• Secure the intravenous drip bag/bottle with
the velcro.
• The IV stand must not be used as a support
when getting up.
• The IV stand can only be used with till Fellow
standard, wide and low.
Safety informaon
Assembling
1. Choose on which the side drip stand should
be assembled on.
2. Assemble a clamp between the pipe of the
front part and grating (screws to the outside
and clamp upwards).
3. Attach the bottom support to the clamp.
Rough adjustment - the attachment pipe of
the bottom support should be assembled
about 1 cm from the protection cover of the
bearings.
4. Assemble the other two clamps on the
frame of the front part under the lock pegs
(the screws pointing outwards and the clamp
straight forward).
5. Put down the pipe in the hole of the bottom
support.
6. Assemble the bended side pipes in the lock
housing. Make sure respectivley side pipe is
placed on the right side.
Note! Do not tighten firmly.

10
www.humancaregroup.com
Assembly Oxygen Holder ENG
Fellow Classic
1. Place the oxygen holder on the graiting of
the rollator.
2. Attach the two hooks on the rear end of the
graiting, A.
3. Attach the basket with a plastic clamp around
the front frame of the rollator, B.
4. Tighten with enclosed screw and knob.
5. Fix the oxygen tank with the velcro at the
oxygen holder, C.
B
C
A
7. Loosen the handle on the lock housing.
8. Put the ends of the side pipes in the clamps
from below.
Note! The pipe ends must match side to
side with the clamp.
8. Tighten firmly.
9. Adjusting to get a vertical dripstand:Achieve
to get the upper clamps to the same height,
pointing forward. Then loosen a little on the
lower clamp, turn it outwards or inwards
depending on preferred angle. There after
move the clamp sideways to achieve the right
sideway angle. When adjustment is ready
tightening all screws and clamps.
Note! Maximum heightening of the drip
stand is when the upper part of the white
mark is getting visible
10. If the drip stand is placed on the right side:
Place the counterweight at the left side, as
close to the side as possible, and secure it
with the two bundle straps.
If the drip stand is placed on the left side: Place
the counterweight at the right side, as close to
the side as possible, and secure it with the two
bundle straps.
The function of the counterweight is to give a
better balance to the rollator and to reduce the
tilt risk.