HUSKY LINERS 47111 User manual

4711 H2 Spare Tire Ca#116FA.doc
H2 Hummer Spare Tire Carrier Mounting Instructions
Tools Required for Installation: Package Contents:
Socket Wrench Swing arm Assembly
19 MM socket Hinge Plate
15 MM socket Striker Plate
7/16” Wrench License Plate Bracket
Torque Wrench Fastener Hardware Bag (Includes):
Drill M12 X 70 MM Flange head bolts X 4
7/16” Drill Bit 10-32 X 3/8” Button head bolts X 2
Center Punch Wire Tie X 3
Hammer Thick Grommet
Phillips Head Screwdriver Thin Grommet
1/8” Allen Wrench 3/8”-24 X _” Hex Bolt & 2” Fender Washer
License Plate Fastener Bag
Jack Support Bracket (Back Page)
Jack Bracket Vibration Dampener
Interior Panel Plug
End Caps (2”X 4”) X 2
Before beginning installation, check to make sure all components listed above are included in packaging.

4711 H2 Spare Tire Ca#116FA.doc
H2 Hummer Spare Tire Carrier Mounting Instructions
1. Remove both tow loops from rear bumper with 18 MM socket.
2. Remove hinge plate from packaged swing arm assembly. To aid in positioning and support of hinge
plate during installation, insert one M12 X 70MM bolt into a driver’s side tow hook mounting hole.
The hinge plate can now be temporarily “hung” on the bolt (head of bolt will fit through hole in hinge
plate). The hinge plate should be oriented with hinge boss towards passenger’s side (see Photo 1).
3. With hinge boss toward the passenger’s side of vehicle, attach hinge plate and tow loop to
passenger’s side using the two M12 X 60 MM flange head bolts provided. Snug bolts with 15 MM
socket but do not tighten. See photo #1 below.
4. Mark and center punch location to drill a 7/16” diameter hole through the bumper on the driver side
as shown in photo #2. Install thin grommet. Wiring for license plate light will pass through this hole.
5. Install thick grommet in 7/16” hole in striker plate assembly where license plate wiring will pass
through. Remove the temporarily placed bolt and install both M12 X 70MM mounting bolts through
the tow loop, striker plate and hinge plate into bumper.Do not tighten bolts until after threading wire.
Thread license plate bracket wires through both installed grommets (liquid soap can be used to
lubricate wires for easier assembly).
6. Mount license plate light/bracket to striker plate with two 10-32 X 3/8” button head bolts provided.
7. Snug the driver and passenger’s side bolts with striker plate in the center of its adjustment range.
8. Install the two (2) provided End Caps in the open ends of the swing arm assembly tubing using a
rubber mallet. Then, install the swing arm assembly by inserting hinge pin into the hinge plate.
9. Install the 3/8”-24 X _” bolt and 2” stainless steel fender washer into bottom of hinge pin, tightening
securely.
10. Close swing arm slowly to striker plate. Adjust striker plate so that the latch pin is centered left to
right in the rubber grommet in the swing arm and lift swing arm so that pin is just touching the
bottom of the grommet.
11. Tighten only the passenger’s side M12 X 60MM bolts to 50 foot-pounds
12. Fully open and close the swing arm several times noting that latch pin/grommet alignment is still in
place and latch is working properly.
13. Make any needed adjustments and tighten passenger’s side bolts to 75 foot-pounds. Repeat step 12.
14. The final torque for the two passenger’s side M12 X 60MM bolts is 100 foot-pounds. Mount the
spare tire using the lug nuts provided. Tighten nuts securely.
15. Open and close fully several times to insure the latch is operating smoothly and properly and the
striker pin is centered in the swing arm grommet. With the added weight of the tire, it may be
necessary to make a final adjustment to the striker plate.
16. Tighten striker plate (driver’s side--12M X 70MM) bolts to 100 foot-pounds
17. Refer to license plate wiring instruction sheet to finish installation.
Photo 1
Photo 2
8”

4711 H2 Spare Tire Ca#116FA.doc
License Plate Light Wiring Instructions
1. In front of rear bumper underneath vehicle on driver side, locate cluster of three plugs. The white
plug housing should have no existing wiring.
2. Remove the white plug housing from receptacle by pushing in the tab and pulling down.
3. Remove the wire retainer from the plug housing.
4. Remove the two orange plugs as shown in drawing.
5. Push terminal ends for tag light into plug as shown in drawing.
6. Replace wire retainer.
7. Route plug housing and wire back to receptacle and plug in firmly to engage tabs.
8. Use provided wire ties to secure excess wire.
Photo below shows finished installation.
9. Install license plate
10. Turn vehicle lights on, check to see that license plate light functions
WIRE
TERMINAL TAB MUST BE DOWN
WHEN INSERTED INTO PLUG
WIRE RETAINER
DO NOT REMOVE
THESE ORANGE PLUGS
WHITE PLUG
HOUSING
INSERT WHITE WIRE
REMOVE THESE
ORANGE PLUGS
Photo Showing Connection of
License Plate Wiring
INSERT BLACK WIRE
License Plate Wires
License Plate Mounting and
Striker Plate Assembly
NOTE: Your Hummer H2 tire carrier is manufactured using the highest quality materials. The
hinge pin is stainless steel and the bushings are oil-impregnated bronze. Lubrication should not be
required. We have included a grease fitting for supplemental lubrication if deemed necessary.
Hummer License Plate Frame Not Included

4711 H2 Spare Tire Ca#116FA.doc
Jack Support Bracket
Once you have removed the inside spare tire carrier, you will need to use the included Jack Support Bracket
to support the top of your jack. To install the bracket, you will need to use the factory bolts and spacer for
correct alignment. Below is a photo of the installed bracket (see photo 1 below). Note that a threaded stud is
attached to the jack bracket. This stud is for storage of the factory tire chocks that were previously attached
to the inside mounted spare tire assembly. Use the factory wing nut from this assembly to secure tire chocks
to the Jack Support Bracket as shown below in photo 2. You will also find in your packaging a Jack Bracket
Vibration Dampener (rubber bumper) that is used for vibration suppression. This bumper should be slid into
place as shown in the photograph below. It should be located approximately 2” from the top of the wheel
well and centered under the jack bracket.
You will also find that once the inside spare tire carrier is removed, an open hole will be left inside the rear
door trim panel where the tire carrier was attached (see photo 4). To fill this hole and give the panel a
“finished” look, we have included a panel plug (see photo 5).
Use the factory tire carrier spacer
behind jack bracket to achieve
necessary spacing.
Attach factory tire chocks to
stud on jack bracket using
factory wing nut.
Hole left by removal of the
factory tire carrier bracket.
Hole shown with provided
panel plug inserted.
PHOTO 2
PHOTO 1
PHOTO 4
PHOTO 5
Jack Bracket Vibration Dampener shown slid
into position behind factory jack support.
PHOTO 3