HUSKY LINERS 47954 User manual

47954_Instruction Sheet.doc
09/11/2006
HUSKY STORAGE BOX INSTALLATION INSTRUCTIONS
Please check contents and read instructions before beginning (some contents inside drawer of box)
You have received hardware for both Excursion and Suburban installation (not all hardware will be used)
PACKAGE CONTENTS
1- Drawer Unit
1- Cam Spacer 1- Handle Assembly
1- 3/8”-24 Lock Nut 2- 3/8”X 2-3/4” Hex Bolts
3- #8 X 1_” Stainless Steel Wood Screw 4- 3/8”X 1-1/2” Hex Bolts
2- 4” Long Straps 1- Cargo Liner Retention Block
1- 45_” Channel Iron (with 2 holes) 1- Cargo Liner
1- Cam latch 1- Drawer Liner (Foam)
2- 3 1/2” Long Clamp Plates 2- 1” Round Spacers
2- M10 X 60 Allen Bolts 2- 5” Long Nut Plates
8-3/8” Flat Washers
TOOLS REQUIRED
1/8” Allen Wrench 8mm Allen Wrench
3/8” Combination End Wrench T-50 Torx Wrench
9/16” Socket and Ratchet Phillips Head Screwdriver
INSTALLATION
1) Before beginning installation, check factory positioning of jack and jack tools. If Storage Box will
block access to these items when installed, remove them before installing Storage Box. These items may
be stored in your Storage Box once installation is completed.
2) Remove Storage Box from packaging. Check to insure you have received all the above listed Package
Contents and that no damage has occurred during shipping.
3) Position Storage Box top side down, placing it on a flat, non-marring surface. Remove shipping blocks
and Channel Iron from bottom of drawer using Phillips Head Screwdriver. Removing block will allow
drawer to slide out so use caution and avoid tilting Drawer Unit.
4) Turn Storage Box back over (right side up and laying flat on a non-marring surface) and extend the
drawer to the full open position.
5) Remove Detent Pin from each drawer slide by applying downward pressure on Detent Pin (see note #1).
Detent Pins will be re-inserted later so do not dispose of them.
6) Remove drawer from the Storage Box and stand it vertically on its back wall (once again on a non-
marring surface). Using a 1/8” Allen Wrench and 3/8” End Wrench, remove the two 10-32 flathead bolts
and nuts from handle installation area. Note that there are spacers (thick washers) located between the front
and rear extrusions that make up the drawer face. Should the spacers move out of position when the bolts are
removed, reposition them before completing handle installation. Repositioning a spacer that has fallen out is
easily done by resting the spacer on your finger and raising the spacer up into the handle opening from the
inside of the drawer. To avoid the spacer falling out do not tip drawer when handle bolts are removed.
7) Remove the 3/8”-24 lock nut, cam latch and spacer from Handle Assembly. Align handle with holes
(shank will pass through opening in drawer) and re-install the 10-32 flathead bolts/nuts using 1/8” Allen
Wrench. On the inside of the drawer, re-install the spacer, cam latch and 3/8”-24 lock nut on handle shank,
tighten nut only finger tight. Turn handle and note the position of the cam latch. The cam latch should be

47954_Instruction Sheet.doc
09/11/2006
oriented on handle shank so that it will secure drawer unit when handle is horizontal on drawer (see note
#2).
8). Remove 3rd row seat(s) from vehicle and fold second row seats forward.
9) With cargo hatch open, remove the two cargo tie-down loops from the cargo area using a T50 Torx
wrench. Position the two short 1” rounds spacers (provided) in the recesses where tie-down loops were
removed. The storage box will later be positioned over these stand-offs and bolted into place.
10) Position a long nut plate (has 3 drilled/tapped holes) under each of the most forward 3rd seat brackets
located on each side of the cargo area (see note #3). Note positioning of nut plate in the photo and situate nut
plate accordingly with the stamped “F” on the nut plate toward the front of the vehicle.
11) Place the two provided 1/2” X 1” X 3-1/2” clamp plates over 3rd seat mounting rods, positioning them
above each nut plate (see note #4). Note that clamp is positioned over the two drilled/tapped holes in the nut
plate that are closest to the rear of the vehicle.
12) Insert two (2) of the 3/8” X 1-1/2” Hex Bolts and flat washers through each clamp, threading them into
Nut Plates. Take care to insure that the Nut Plates/Clamps are positioned so that they will be pulled against
both of the 3rd seat mounting rods when bolts are tightened (review positioning in note #4). Do not tighten at
this time.
13) Remove Access Panel from rear of Storage Box using a 1/8” Allen Wrench. Carefully slide Storage Box
into cargo area.
14) Position Channel Iron horizontally over the forward set of holes in the nut plate and insert the two (2)
3/8” X 2-3/4” Hex Bolts and flat washers through the 2 holes in the channel iron, threading them into Nut
Plates (see note #5). Do not tighten at this time.
15) Insert the two, 4” pieces of strap so that one piece is centered under each end of the Channel Iron where
Channel Iron contacts Storage Box (see note #5).
16) Install M10 X 60 Allen bolts and washers through case and 1” round spacers and into threaded holes that
held tie-down loops. (It may be necessary to raise the front of the box to allow bolt to start) Tighten
securely.
17) Evenly tighten all eight bolts, do not over tighten.
18) Guide drawer back into drawer slides and re-insert detent pins.
19) Install Drawer Liner (foam) into drawer.
20) Install Cargo Liner by first centering liner on top of Drawer Unit. Then, insert the Cargo Liner Retention
Block into the recess molded into the cargo liner. Using the Phillips Head Screwdriver, install the three #8 X
1-1/4” Stainless Steel Wood Screws through the holes in the Retention Block and into the top of the Storage
Box (see note #6). Take care to make sure the liner is center before attaching.
21) Your Storage Box should be treated as you would the exterior of your vehicle. Wash with gentle soap
and water and rinse well. The easiest way to clean the drawer liner or cargo liner is with a damp cloth or
sponge. If using a cleaner, 409® or Glass Plus® work well. The use or Armor All®, Son-of-a-Gun® or
similar items is discouraged as the products make the liner slick.
22) Your Husky Storage Box comes with a limited one-year warranty. Winfield Consumer Products
warrants its SUV Storage Box to be free from defects in material and workmanship of the product for one
year, from the date of purchase, with proof of purchase.

47954_Instruction Sheet.doc
09/11/2006
Note #2-Position Handle so Cam Latch will
be pointing up when handle is horizontal.
Note #1-Removing Detent Pin
Cam Latch
Detent Pin
Note #3—Showing placement and orientation of
nut plate under seat mount brackets.
Note #4—Showing placement and orientation of
clamp plate over seat mount brackets and nut plate.

47954_Instruction Sheet.doc
09/11/2006
Retention
Block
Note #6-Retention Block shown installed. Take
care to center liner before installing block.
Note #5—Showing placement and orientation of Channel Iron and 4” Strap. Position strap on inside rail
of Storage Box, centered under Channel Iron.
4” Strap