Husky 33144 User manual

2TIERWDHITCHDISPLAYSTAND
1
01/15/18_REV2
PART#33144

Toolsrequired:
Ratchetwrench
¾”Socket
¾”Boxendwrench
TorqueWrench
Allhardwarewillbefinaltorquedto75ft.lbs.
2
01/15/18_REV2
PartsList

1.PositiontheBaseCenterTubeandBaseRearTubeasshown.
Connectthetubesusingtheproperhardwareandlightly tighten.
2.AttachtheLowerHitchBoxWeldmenttotheBaseCenterTubeusingthe
properhardwareandlightlytighten.
3.Attach(2)Feetusingtheproperhardwareandlightly tighten.
4.Ensurebothfeetandtherearbasetubelieflatonthefloor.Torqueall
hardwareto75ft.lbs.
3
01/15/18_REV2
BaseAssembly

5.AttachaBaseVerticalLegtoeachsideoftheBaseRearTube.Torqueall
hardwareto75ft.lbs.
4
01/15/18_REV2
UprightAssembly

LowerAFrameAssembly
6.AssembletheCouplerBodytoeachRectangularTubewhileonaworkbench
orfloorbeforeattachingtothestandbase.Note:Theendofthetubewiththe
singleholeisattachedtothecoupler.Lightlytightenhardware.
5
01/15/18_REV2

7.InstalltheShankandHeadAssemblywithHitchBallthatwillbedisplayedon
thestand(Notincluded).Thiswillallowyoutoalignthedisplaystandproperly.
8.Using2people,carefullyplacetheassembledAFrameonthestandand
attachtheCouplertotheHitchBall.
9.InstallthehardwaretoattachtheRectangularTubingtotheBaseVertical
Legs.Lightlytightenhardware.
6
01/15/18_REV2

BesurethehitchballisattheproperheighttoallowtheAframetositlevel.
Adjusttheballheightifnecessary.
7
01/15/18_REV2
AligntheAFramesobothsidesareatthesameangle.Torqueallhardwareto
75ft.lbs.

PlateAssembly
10.Theplatescanbeattached2ways.Forlongerlengthhitchdisplays,
assemblewiththestraightsidetowardsthefrontofthestand.Forshorter
lengthhitchdisplays,assemblewiththeangledsideoftheplatestowardsthe
frontofthestand.Installallhardwareandlightlytighten.
Note: Thehookplatecanbeinstalledoneitherside.
8
01/15/18_REV2
StraightSide AngledSide
Frontofstand

UpperAFrameAssembly
11.TemporarilyremovethehitchpinfromtheLowerHitchBox,installthe
UpperHitchBoxWeldment,thenreplacethehitchpin.
12.InstalltheShankandHeadAssemblywithHitchBallthatwillbedisplayed
onthestand(Notincluded)intheUpperHitchBox.Thiswillallowyoutoalign
thedisplaystandproperly.
9
01/15/18_REV2
HitchPin

Repeatstep6toassembletheupperAFrameAssembly.
13.Using2people,carefullyplacetheassembledAFrameonthestandand
attachtheCouplertotheHitchBall.
14.InstallthehardwaretoattachtheRectangularTubingtoPlatesA&B.
Lightlytightenhardware.
Note: Thehookplatecanbeinstalledoneitherside.
BesurethehitchballisattheproperheighttoallowtheAframetositlevel.
Adjusttheballheightifnecessary.
AligntheAFrameasdescribedonPage7,thentightenallhardwareto75ft.
lbs.
10
01/15/18_REV2
TheStandassemblyisnowcomplete.
Installspringbars,brackets,orswaycontrolsonyourdisplayasdesired.