hygena Berkeley 411/9681 User manual

MADE IN
BRITAIN
Dimensions
Width - 49.5cm
Depth - 33cm
Height - 165cm
Berkeley - Bookcase
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 11/05/15
Important - Please read these instructions fully before starting assembly
ALR3151
411/9681
hygena

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 24kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left End (DF2899)
(1498 x 325mm)
Top (DF2897)
(495 x 327mm)
2Right End (DF2900)
(1498 x 325mm)
Divider (DF1260)
(363 x 243mm) x 4
Back (X1524-487)
(1524 x 487mm)
Base (DF2898)
(495 x 327mm)
5 6 7
8
Top/Bottom Shelf (DF2902)
(461 x 323mm) x 2
4
Middle Shelf (DF3746)
(461 x 323mm)
3
These 2 holes are
through-holes
These 2 holes are
through-holes

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H
C
Nail (F51) x 30
40mm Screw (F910) x 4
I
Large locking
nut (F900) x 16
Metal dowel (F901) x 16 Wooden dowel (F22) x 16
Leg (F343) x 4 Leg Bracket
(F333) x 4
Strap Screw Washer x 2
Overbalance protector kit (F269) x 1
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
13mm Screw (F79) x 16

Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Step 2
Prepare the left end
Screw 6 metal dowels
into the left end .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
1
A
A
A
A
A
A
A
B
B
B
1
B
1
80% x 2
A
A
A
A
A
A
B
B
Prepare the right end
Screw 6 metal dowels
into the right end .
Insert 2 large locking
nuts into the right
side .
A
2
B
2
Step 3
Prepare the middle
shelf
Insert 4 large locking
nuts into the middle
shelf .
B
3
Finished
front edge
2
B
B
B
B
Finished
front edge
Through-holes
Note: The middle shelf
is similar to the top and
bottom shelf. Make sure
that the finished edge
and the holes are in the
same position as the
diagram.
3

C
Finished
front edge
Finished
front edge
Assembly Instructions
5
Step 4
Step 6
A
B
Fit the middle shelf to
the right end
Push the middle shelf
onto the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the middle shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
3
B
B
3
2
3
C
C
C
10mm
C
Finished
front edge
Prepare the 4 dividers
Tap 4 wooden dowels
into each of the 4
dividers .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
7
Step 5
Prepare the top and
bottom shelves
Insert 4 large locking
nuts into the top shelf
. and the bottom shelf
. .
B
4
4Finished
front edge
B
B
B
B
Finished
front edge
B
B
B
B
4
4
7
x 4
Through-holes
Through-holes
Through-holes

Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 7
Fit a divider
Push a divider onto
the middle shelf .
3
7
Fit the bottom shelf
Push the bottom shelf
onto the right end
and the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the bottom shelf .
2
7
4
B
4
3
7
7
4
2
Step 8
3
Step 9
7
Fit a divider
Push a divider onto
the middle shelf .
3
7
Through-holes

Assembly Instructions
7
Step 10
Finished
front edge
Finished
front edge
Step 12
Step 11
Fit the top shelf
Push the top shelf
onto the right end
and the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top shelf .
2
7
4
B
4
2
7
4
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the middle shelf , top
shelf and bottom
shelf .
1
B
3
4
4
1
3
4
4
Finished
front edge
Fit a divider
Push a divider onto
the bottom shelf .
4
7
7
4
Through-holes

Finished
front edge
7
Assembly Instructions
8
Step 13
Step 15
Step 14
Fit the base
Fit the base onto the
left end and the right
end using 4 screws .
6
D
1
2
DD
D
D
6
1
2
A
Prepare the top
Screw 4 metal dowels
into the top .
A
5
Finished
front edge
A
A
A
5
Fit a divider
Push a divider onto
the top shelf .
4
7
4

Finished
front edge
Assembly Instructions
9
Step 16
Step 17
Fit the top
Push the top onto
the left end and the
right end .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and the
right end .
1
2
1
2
5
B
1
5
2
Note: The raised part
of the leg bracket must
point towards the
centre of the panel.
Fit the leg brackets to
the base
a: Screw each leg
bracket . to the base
using 2 screws into
the mark holes.
b: Then use another 2
screws into the other
2 holes.
6
H
E
E
H
E
E
H
HH
H
6