hygena Luna 460/5339 Datasheet

Assembly lnstructions - Please keep for future reference
Luna Coffee Table
Width - 90cm
Depth - 45cm
Height -45cm
Dimensions
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Important - Please read these instructions fully before starting assembly
Issue 1-23-10-15
460/5339
hygena

Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Assembly requires 2 people.
Do not stand or put excessive
weight on the product,this could
cause damage.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers and
Allen keys.
Dispose of all packaging
carefully and responsibly.
1
Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
This product has been finished using natrual materials. As a living material, you may notice some
variation in the grain and colour shade between the different components.
Unlike a synthetic or man-made material which has a uniform finish, a feature of natural wood is its
variation in grain and colour. We wish to reassure you that this is quite normal and is not the result
of any manufacturing fault.
Where sheets of wood are joined together, a line may be detected. Again, this is normal and is not
an imperfection.
The natural finish should be cared for by the periodic application of a good quality 'was' based
domestic furniture polish (Not silicone!!). Occasional / small spills should be removed immediately
using a damp cloth.
Do not allow hot articles to come into contact with the surface, as damage will occur!

Components - Parts lf you have damaged or missing components.
call the Customer Helpline: 0345 6400 800
2
6
5
4
12
Rear stretcher (with groove)
(74x50x1.5cm)
Front stretcher
(74x50x1.5cm)
Side frame (right)
(42.5x42x5cm)
3
Side frame (left)
(42.5x42x5cm)
Back panel
(75x16x0.3cm)
Top
(90x45x2.5cm)
7Drawer back
(70.9x11.9x1.2cm)
8Drawer side panel (right)
(31x11.9x1.2cm)
10
9
(31x11.9x1.2cm)
Drawer base
(71.5x30.4x0.3cm)
11
(73.7x16.5x1.5cm)
Drawer side panel (left)
Drawer front
12
(29.7x5x1.2cm)
Drawer support
inside
underside
inside
underside
13
(74x2.5x1.5cm)
Apron
groove

3
0345 6400 800
BC
D
G
EF
A
F
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
0
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150
1 2 3 4 5 6 Ruler/tape measure
Components - Fittings
Metal dowel x 13
Wooden dowel x 10 (6X30mm)
Phillips screwdriver
(Not supplied)
Drawer runner x 2 (L342mm) Wood screw x 8 (4x30mm) Screw x 4 (3x12mm)
Screw x 2 (4x10mm)
H
Wood screw x 2 (4x25mm)
J
K
Handle x 2
Large locking nut x 4
Small locking nut x 9

1
2
2
3
11
B
B
B
E
EE
E
E
E
E
E
A
F
F
13
Preparing panels
Assembling drawer
runners
Assemble drawer runners
to side frames and
using screws .
A
A
3
E
Place top , side frames
and , and drawer front
flat onto the floor with the
fixing holes facing up .
Screw metal dowels into
all panels as shown.
Insert wood dowels into
side frames and and
top as shown.
Assemble apron to top
using screws .
2
2
13
1
1
3
23
3 11
1
B
Note:Screw metal dowels
as far as shown. Do not
overtighten.
Note: The drawer runners
should be fixed through the
holes shown. It will be
necessary to extend/close
the runners to gain access to
the holes.
A
F
F
D
E
B
B
D
D
D
D
D

1
2
2
3
3
6
K
C
A
BK
BK
BC
5
3
Step 4
Align
Grooves
4
5
Rear
Front
Assembling stretchers
Locate front and rear
stretchers and in
between side frames
and .
4
4
2
3
5
3
1
6
2
32
A
Insert large locking nuts
into the holes in the underside
of stretchers and .
Turn locking nuts clockwise to
secure.
Note:Ensure the groove in
the top surface of rear
stretcher is correctly
aligned withthe grooves
in the side the frames.
45
Assembling top and back
panel
Carefully slide back panel
into the grooves in side
frames and .
With help carefully stand the
unit upright.
Insert wood dowels
into the top of side frames
and .
Insert small locking nuts
into side frames and
.
Locate top into position.
Turn locking nuts clockwise
to secure.
C
3
2

7
8
9
11
11
12
a:
b:
c:
d:
C
C
F
F
F
F
BC
6
Step 5
G
H
10
11
12
8
9
C
F
F
G
H
Assembling Drawer
a: Locate drawer sides
and and support onto
drawer front .
Note:Ensure the grooves
on all panels align at the
bottom.
Insert small locking nuts
into the drawer sides and
support as shown.
Turn locking nuts clockwise
to secure.
b: Slide drawer base into
the grooves.
c: Assemble drawer back
using screws .
d: Fit handles to drawer
front using screws .
11
7
10
Align grooves

7
Step 6
J
JJ
J
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Home Retail Group. 489-499 Avebury Boulevard. Saxon Gate West. Central Milton Keynes. MK9 2NW
Locating drawer
With help, turn the whole unit
upright.
Extend the drawer runners
fully out.
Locate the drawer onto the
runners and secure using
screws as shown.