hygena Bergen SHELF PACK User manual

Bergen SHELF PACK
180 x 200 x 53cm
Dimensions
Width - 87.7cm
Depth - 48.8cm
Height - 1.8cm
Assembly Instructions- Please keep for future reference 238/6777
DR8250340
Issue 3 - 05/11/15
Important–Please read these instructions fully before starting assembly
Alternatively, call the Spares Helpline on: 0370 112 1928
For any other queries please contact the Customer Helpline on: 0345 640 2020
If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk
or email: [email protected] (quoting your original order number)

Safety and Care Advice
Important –Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
the following pages.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
2

Tools required
Eye protection
(when using a
hammer or drill)
Note: The quantiti es below are the correct amount to complete the assembly. In some cases more 1/1
Please check you have all the fittings listed below
Components - Fittings
Scissors
Small locking screw x 6
FK1056
Cam 20x12mm Expando housing x 6
FK1051
12,5mm Screw x 8
FK1309
Shelf support with fixinghole x 8
FK1207
B
C
D
A
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
P1900
Horizontal
(87.7 x 48.8cm)
1
P1902
Shelf x 2
(87.7 x 48.8cm)
2
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head to the point (30mm screw shown).
For damaged or missing parts, please visit:
www.argos-support.co.uk or email: [email protected]
Components - Panels
Please check you have all the panels listed below
3

Assembly Instructions
Step 1
Insert the fittings
a:
change the place of one
hanging-rail as shown.
b:
Insert 6 small locking
screws Aas shown.
a:
b:
A
4

Assembly Instructions
Step 2
a: Push Cam Expando
housing Binto the hole of
the Horizontal 1.
b: Turn Horizontal 1and
lower it onto the small
locking screws A.
c: Tighten the Cams B
with a Philips screwdriver.
B
B
B
B
B
B
x6
1
b:
c:
B
a:
Inserting Horizontal
1
1
5
B
1

a:
b:
Assembly Instructions
Step 3
inserting shelves
a: Push shelf supports Cin
hole as shown.
b: Position shelves 2onto
shelf supports Cand fix by
screwing eight
chipboardscrews Dthrough
shelf supports Cinto
shelves 2.
2
2
C
2
C
D
6