hygena 656/5831 User manual

MADE IN
BRITAIN
Dimensions
Width - 60cm
Depth - 59cm
Height - 87cm
Valencia - Under Oven Cabinet
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 05/08/14
Important - Please read these instructions fully before starting assembly
ALR2659
hygena
hygena
656/5831
656/6720
656/6744
205/4281
656/6737
203/8104
Cabinet
Black Door Pack
Cream Door Pack
Oak Door Pack
White Gloss Door Pack
White HN Door Pack
Issue 2 - 05/08/14 - Replaced Grey and Plum codes with Oak and White HN codes.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 16.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Parts of the assembly will be
easier with 2 people.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
+
90%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
2
4
3
Left Side (DPF068A)
(720 x 560mm)
Right Side (DPF069A)
(720 x 560mm)
Base (DPF078A)
(569 x 494mm)
Cross Rail (DPF080A)
(569 x 96mm) x 2
5Support Rail (DPF112A)
(495 x 105mm) x 4
The front surface of this fascia
is protected with a peel-off film
Appliance Fascia (DPF124B)
(596 x 120mm)
6

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
see malibu fitment mk2 for large number of panels and fittings
Tools required
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 8
C
D
Large locking
nut (F900) x 8
G H
K
I a
I c
I d
I e
I b
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
Electric drill
E
13mm Screw (F79) x 14
Connecting Sleeve (F432) x 2 19mm Connecting bolt (F461) x 2
Bracket (F945) x 8
Leg Bracket
(F127) x 2
Leg Socket
(F120) x 4
Leg Clip
(F128) x 2
16mm Screw
(F129) x 16
Leg (F122) x 4
45mm Screw (F65) x 4
F
25mm Screw (F50) x 2
38mm Screw (F933) x 4

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
80% x 2
B
B
J
J
J
E
1
BJ
E
5mm
150mm
B
B
B
1st 5mm hole
2nd 5mm hole
1
Prepare the left side
Screw a metal dowel
into one of the holes
shown on the left side
. .
Note: Tighten metal
dowels up fully against
the panels.
Important: The position
of the metal dowel
depends on where you
would like the cross rail
to be.
B
1
B
The hole chosen for the metal
dowel determines the position of
the rear cross rail.
This will depend on where the
services to the oven will be located.
We recommend that you consult a
qualified joiner or kitchen fitter.
Step 2
Prepare the left side
Screw 3 metal dowels
into the holes shown on
the left side .
Note: Tighten metal
dowels up fully against
the panels.
Fit a bracket flush to
the top edge of the left
side , about 150mm
in from the groove, see
diagram.
Secure the bracket
using screw .
Fit another bracket
flush to the back edge of
the left side , about
5mm down from the top
edge, see diagram.
Secure the bracket
using screw .
Note: The brackets must
be flush with the
top/back edge of the
panel.
B
1
J
J
1
J
1
E
J
E
Only screw ONE metal dowel into
one of these holes.

Assembly Instructions
5
Step 3
Step 4
Prepare the right side
Screw 3 metal dowels
into the holes shown on
the right side .
Fit a bracket flush to
the top edge of the right
side , about 150mm
in from the groove, see
diagram.
Secure the bracket
using screw .
Fit another bracket
flush to the back edge of
the right side , about
5mm down from the top
edge, see diagram.
Secure the bracket
using screw .
B
2
J
J
2
J
2
E
J
E
J
E
B
B
B
J
J
2
J
E
Prepare the right side
Screw a metal dowel
into one of the holes
shown on the right side
. .
Use the same hole that
you used for the left side
in step 1.
B
B
2
2
Only screw ONE metal dowel
into one of these holes (use
the same hole that you used
for the left side in step 1).

Assembly Instructions
6
Step 5
Step 6
Step 11
Secure the back
The bottom edge of the
back must be flush
with the bottom edge of
the base .
Secure the back to
the back edge of the
base using 3 screws
. .
Stand the unit up for
the next stage.
F
6
6
3
3
F
6
3
F
F
Fit the back
Slide the back along
the grooves in the side
panels and .
3
6
6
1 2
1
2
I a I a
I b
b: c: d:
Fit the legs to the
base
a: Push the leg sockets
. into the holes in the
base as shown.
b: Secure each leg
socket with 3
screws .
c: Tap in the centre plug
on each leg socket .
d: Push the leg into
the leg socket .
I a
I a
I a
I e I e
3
x 3
I a
I a
I b
I a
I a
I a
I a
3
A
A
Prepare the base
Insert 4 large locking
nuts into the base
as shown.
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Tap 6 wooden dowels
into the base as
shown.
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
C
C3
10mm
A
A
3
A
A
A
C
C
C
C
A
3

Assembly Instructions
7
Step 7
4
Fit the 2 cross rails
Push each cross rail
onto the right side .
Use a screwdriver to
tighten the large locking
nut fitted to each
cross rail .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
C
C
4
2
4
4
Support the rear cross rail
until the left side has been
fitted in the next step.
Finished
front edge
Step 6
Step 8
A
C
Prepare the 2 cross
rails
Insert 2 large locking
nuts into the cross
rails as shown.
Tap 2 wooden dowels
into the cross rails as
shown.
Step 9
4
4
A
Join the right side and
base
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
F
3
3
2
C
C
2
3
A
C
C
4
You may have
selected to fit the
rear cross rail here
(refer back to step 1).

Assembly Instructions
8
Step 10
Step 11
Fit 2 support rails
Fit a support rail to
the right side using 2
screws .
Fit a support rail to
the left side using 2
screws .
Note: The support rails
must be flush with the
front of the unit.
Step 12
Prepare the other 2
support rails
Fit 2 brackets flush to
one end of the remaing
support rails using
screw .
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the large locking
nut fitted to the 2
cross rails and the 2
fitted to the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
1
C
C
4
4
1
4
3
1
2
K
K
K
K
5
5
5
1
2
K
5
K
J
J
J
E
E
J
J
E
E
5
5
E

Assembly Instructions
9
Step 13
M
Step 14
Fit 2 support rails
Fit a support rail flush
with the support rail on
the right side using 2
screws .
Fit a support rail flush
with the support rail on
the left side using 2
screws .
D
D
1
2
5
1
2
D
5
D
Warning: Take
care when
drilling the wall
that you do not
drill into any pipes, wires
etc. If in doubt, consult
an expert.
1
2
D
D
5
5
Secure the unit to the
wall
Using the brackets
fitted to the back edge of
the sides and
screw the unit to the
wall.
Fixings are not supplied
as they will need to suit
the wall type, and the
length of screw will
depend on the distance
of the back of the Unit to
the wall.
J
1 2