hygena Amparo 633/3252 User manual

Amparo Chair
Dimensions
Width - 58cm
Depth - 49cm
Height - 75cm
Issue 1 - 02/04/11
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly Instructions - Please keep for future reference 633/3252
633/3276

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
page 2.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Only clean using a dry cloth,
do not use bleach or abrasive
cleaners.
• Make time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Maximum safe weight of user:
110kgs.

Components - Panels
Please check you have all the panels listed below
2
If you have damaged or missing components,
call the Customer Helpline:
0845 6400800
The quantities below are for 4 chairs
1Chair back x 4
(54.2 x 34.7 cm)
2Chair seat x 4
(52.6 x 39.5 cm)
4Chair leg x 4
(57.7 x 42.9 cm )
3Chair leg x 4
(48.8 x 43.2 cm)

A
Tools required
Ruler - Use this ruler to help correctly identify the screws
100 20 30 40 50 60 70 80 90 100
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Components - Fittings
Please check you have all the ttings listed below
64mm Bolt x 16 32mm Bolt x 16
B
28mm Bolt x 4
C
Note: The quantities below are the correct amount to complete the assembly of 4 chairs. In some cases
more ttings may be supplied than are required.
Nut x 4
D E F
G H I
Insert nut x 16 Plain washer x 20
Spring washer x 16 Bolt cap x 16
Flatblade screwdriver
3
Hex key x 1
Wrench x 1
J

Assembly Instructions
Step 1
Step 2
C
Assemble seat and
back
Two people are needed
here
a: Place chair seat 2
upside down, put insert
nuts Einto the holes on
the underside of the seat,
make sure the threaded
hole of the insert nut is
aligned with the holes in
the edge of the chair seat
as shown in the gure.
4
3
D
2
Assemble legs
Assemble chair leg 3
and 4using bolt C,
plain washer Fand nut
D.
Note: Do not fully
tighten the bolts.
4
F
E
E
E
E
a:
Continued on next page.

Assembly Instructions
Step 2 - continued
Step 3
2
A
Assemble legs
Fix the chair legs to the
seat using bolts B.
Note: Re-tighten all the
bolts and nuts.
B
b: Assemble chair back
1to the seat using bolts
A, spring washers G
and plain washer F, and
secure tightly by using
hex key J,
Note: Use a screwdriver
to turn the insert nut
slightly as shown in the
gure if the bolt could not
screw in.
B
B
B
F
G
b:
1

Assembly Instructions
Step 2 - continued
H
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
H
Assemble bolt cap
Turn the chair to back to
its up- right position, then
cover the bolts on the
back of the chair with bolt
cap H.
Assembly is complete.
H
H