hygena 417/9810 User manual

Dimensions (4')
417/9810
Assembly Instructions Please keep for future reference
Important Please read these instructions fully before starting assembly
Length - 203cm
Width - 130cm
Height - 85cm
If you need help or have damaged or missing parts, call the Customer Helpline: 0345 6400 800
Issue 1-24/06/15
Attenborough 4',4'6"and 5' Ottoman Beds
404/8972
Dimensions (4'6)
Length - 203cm
Width - 145cm
Height - 85cm
hygena 413/6822
418/1279
417/8536
381/4561
418/6463
418/6614
418/7981
Dimensions (5')
Length - 213cm
Width - 160cm
Height - 85cm
417/9810

Safety and Care Advice
Check you have all the
components and tools listed on
pages 2, 3 and 4.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Assembly requires 2 people.
Do not fully tighten bolts until the
whole bed is assembled. Do not
overtihgten the nuts to avoid
causing damage to the threads.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers and
Allen keys.
Dispose of all packaging
carefully and responsibly.
Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Important Ottoman Safety Warnings
· Caution.This bed uses a pressurised mechanism.
· Use caution when operating - Always use two hands at arm’s length, and only where
illustrated on the product.
· You must ensure the mattress is on the bed frame before lifting the mechanism - Failure
to do so may result in injury.
· Please ensure Children and pets are kept away from the bed when operating the bed
mechanism.
· If removing the mattress, make sure that the frame is secured as it could flip open.
· Only use the storage compartment when the frame is fully raised in the ‘up’ position.
· No children or animals are left unattended when the frame is in the ‘up’ position.
· Do not remain on the bed whilst the lifting mechanism is in use.
· Beware of Entrapment - Keep both hands clear of mechanism when operating the
mechanism.
· When lifting the bed remove all bedding - Except the fitted sheet.
v.jpg X.jpg

2
0345 6400 800
Side rail x 2 (4'-1930 × 310mm)(4'6-1930 × 310mm)
(5'-2030 × 310mm)
Headboard
(4'-1300 × 810mm)(4'6'-1445 × 810mm)
(5'-1600 × 810mm)
Footboard
(4'-1300 × 310mm)(4'6-1445 × 310mm)
(5'-1600 × 310mm)
Hinges (x 1 pair)
(750 x 115mm)
Piston x 2
(420mm)
Base panel x 2
(4'-600× 1228mm)(4'6-600 × 1379mm)
(5'-600 × 1528mm)
Feet x 4
(62 x 33 x 41.6mm)
Long support leg x 1 (Ø25 × 190mm)
Ottoman end frame x 2
(4'-1210 × 118mm)(4'6-1360 × 118mm)
(5'-1510 × 118mm)
FRONT
INSIDE
Base panel x 1
(4'-724× 1228mm)(4'6-724 × 1379mm)
(5'-824 × 1528mm)

3
0345 6400 800
Ottoman side frame (4'-1822*30mm)(4'6-1822*30mm)
(5'-1925 × 30mm)
Note: Extra holes
Bentwood slats x28 (4'-598*9*53mm)
Bentwood slats x28 (4'6-673*9*53mm)
Bentwood slats x30 (5'-748*9*53mm)
Ottoman centre rail x 1
(4'-1822*30mm)(4'6-1822*30mm)(5'-1925 × 30mm)
Base support x 4
(120 x 20mm)
Central support x 1
(4'-1930*80mm) (4'6-1930*80mm) (5'-2030*80mm)
Short support leg x 2
(Ø25*36mm)
Wooden support rail x 2
(4'-1230*60mm)(4'6-1381*60mm)(5'-1530*60mm)
Double slat caps x 14 (4'-5.5mm)
Double slat caps x 14 (4.6-5.5mm)
Double slat caps x 15 (5'-5.5mm)
Single slat caps x 28 (4'-5.5mm)
Single slat caps x 28 (4'6-5.5mm)
Single slat caps x 30 (5'-5.5mm) Corner bracket x 4 (120 × 80mm)
Ottoman side frame
(4'-1822*30mm)(4'6-1822*30mm)(5'-1925 × 30mm)
Mattress support
bracket x 2 (Ø6*78mm)

Nut x 4
0345 6400 800
B C
D E
4
19mm Flat washer x 12
35mm M4 Wood screw x 28
A
F
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Ruler/tape
measure
Components - Fittings
G
25mm M8 Bolt x 20 15mm M6 Bolt x 30
H
14mm Flat washer x 4
5mm Allen key x 1
J
K
Phillips screwdriver
(Not supplied)
PLIERS (Not
supplied)
Plastic cap x 2
4mm Allen key x 1
Spanner x 1

Assembly Instructions
5
Attaching feet
a:Attach 2 x feet to
the underside of the
headboard using
screws as shown.
Repeat on the underside
of the footboard .
Note: The position is
outlined.
2
9
C
3
9
9
2
C
3
C
3

6
a: Attach base supports
to the headboard
and footboard using
screws as shown.
Note: The positions
should be outlined.
C
15 2
3
Assembly Instructions
b:
2
A
A
3
b: Loosely fit bolts into
headboard and
footboard as shown.
A
2
3
a:
2
3
C
C
15
15
Carefully place headboard
and footboard flat
on the floor with the fixing
holes facing up.
23

7
With help, raise the
headboard into the
standing position.
Hang the metal brackets
on the end of the side
rails , over the bolts in
the headboard .
Note: Do not fully tighten
bolts at this stage.
Finger tighten only.
Repeat to assemble
footboard .
1
2
1
2
1
2
3
A
Assembly Instructions
2
1
A
3

21
8
Preparing base
a:Attach the short
support legs to the
underside of the central
support using bolts
.
Fit plastic caps into
support legs .
b:Assemble central
support in between
headboard and
footboard using
fixings and at both
ends.
c:Assemble corner
brackets into each
corner using screws .
Note: Ensure these are
at the same height as all
other metal support bars.
The positions should be
outlined.
d:Assemble wooden
support rails in
between side rails
using screws .
Finally, fully tighten all
other fixing points from
previous step 3 .
d:
b:
17
16
B
17
F
16
2
3
B
C
21
18
1
B
Assembly Instructions
C
C:
a: F
B
17
16
16
B
16
3
2
1
1
1
18
18
18
1
1
2
21
1
21
2
J
J
B

9
Assembly Instructions
With help, carefully slide
base panels and
inside the bed frame as
shown.
6
Completing base
7