hygena 833/4455 User manual

Floor Cabinet
Dimensions
Width - 35cm
Depth - 30cm
Height - 90.5cm
Important – Please read these instructions fully before starting assembly
Assembly Instructions- please keep for future reference 833/4455
Issue 1 - 21/04/11
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 1 and 2.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp
cloth and mild detergent, do
not use bleach or abrasive
cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
1 Top x 1
(35(w)cm x 30(d)cm)
2 Left side x 1
(89(h)cm x 28.5(d)cm)
3 Right side x 1
(89(h)cm x 28.5(d)cm)
4 Base x 1
(29(w)cm x 28.5(d)cm)
5 Back panel x 1
(80.5(h)cm x 31(w)cm)
6 Door x 1
(78(h)cm x 28.5(w)cm)
7 Shelf x 2
(30(w)cm x 26(d)cm)
1

Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
A B C D
35mm Male camlock x 8 Female camlock x 8 30mm Wooden dowel x 2 Magnetic catch x 1
E F G H
14mm Screw x 2 Hinge x 2 10mm Screw x 9 Magnetic catch plate x 1
I J K L
16mm Screw x 2 Handle x 1 Shelf bracket x 8 Safety strap x 1
M N O P
10mm Screw x 1 Back panel screw x 12 35mm Screw x 1 Washer x 1
Q
Rawl plug x 1
Tools required
Phillips screwdriver
(medium & large) Drill (for wall drilling only)
Ruler – Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
2

3
Assembly Instructions
Step 1
Fix 4 x 35mm male
camlock A and 2 x
30mm wooden dowel C
into underside of top 1
as shown.
Connect safety strap L
to underside of top 1
using 1 x 10mm screw
M as shown (a:).
Connect magnetic catch
D to underside of top
1 using 2 x 14mm
screw E as shown (b:).
Step 2
Insert 4 x female
camlock B into
underside of base 4 as
shown.
Using Camlocks
Step 1
Connect the male
camlock as directed in
the assembly instructions
using a screwdriver.
Step 2
Insert the female
camlock as shown in the
instructions.
Note: ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Step 3
Push the male camlock
into the entry hole.
Step 4
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
1
A
C
a:
b:
L
M
D
E
B
4

4
Assembly Instructions
Step 3
Screw 2 x male camlock
A into reverse of drawer
front 13 as shown.
Step 4
Connect hinges B to
top door 5 and bottom
door 6 using 15mm
screws F as shown.
Step 5
Insert 4 x 15mm female
camlock E into under
side of top base 7 as
shown.
Insert 4 x small wooden
dowel D into top shelf
9 as shown.
Assembly Instructions
Step 3
Fix 2 x female camlock
B and 2 x 35mm male
camlock A into left side
2 and right side 3 as
shown.
Step 4
Connect base 4
to right side 3 as
shown and tighten the
female camlocks in the
underside of base 4
with a screwdriver.
Note: the groove in base
4 must line up to the
groove in right side 3
(i.e. to the rear of the
unit).
Step 5
Connect left side
2 to base 4 as
shown and tighten the
female camlocks in the
underside of base 4
with a screwdriver.
B
A
23
4
3
2
4

5
Assembly Instructions
Step 6
Connect top base 7
and top shelf 9 to top
right side 2.
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 7
Connect top left side 1
to exposed ends of top
base 7 and top shelf
9 as shown
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 8
Screw 4 x male camlock
A into the under side of
top 10 as shown.
Step 9
Connect top 10 as
shown.
Tighten female camlocks
with a screwdriver.
Assembly Instructions
Step 6
Connect top 1 to left
and right sides as shown
and tighten the female
camlocks inside the unit
with a screwdriver.
Note: the groove in top
must line up with the
grooves in the left and
right sides (i.e. to the rear
of the unit).
Step 7
Connect back panel 5
to the rear of the unit as
shown using 12 x back
panel screw N.
Note: ensure the safety
strap sticks through the
hole in the back panel to
enable securing to a wall
(see Step 10).
1
5
N

6
Assembly Instructions
Step 8
Connect door 6 to the
unit using 2 x hinge F
and 8 x 10mm screw G
as shown (c:).
Connect handle J to
door using 2 x 16mm
bolt I as shown (d:).
Connect catch plate H
to door using 1 x 10mm
screw G.
Note: catch plate H
must be attached with
the countersink facing
outwards so as to
accommodate the screw
head.
Step 9
Insert 8 x shelf bracket
K into holes inside
the unit at the desired
heights ensuring
that each set of shelf
brackets are level with
each other.
Set 2 x shelf 7 onto
shelf brackets as shown.
Note: the cut away
edges of shelf 7 must
face the sides of the unit.
c:
d:
F
G
J
I
K
7
7
H
G
6

7
Assembly Instructions
Step 10
To prevent accidental
toppling it is
recommended to x the
safety strap to a wall as
shown using 1 x rawl
plug Q, 1 x washer P
and 1 x 35mm screw O.
Note: see the back cover
for more information
on wall mounting and
the suitable use of the
supplied rawl plugs.
Warning:
Before drilling,
check wall for
hidden pipes
and cables.
Assembly complete.
Q
P
O

8