hygena Berkeley User manual

MADE IN
BRITAIN
Dimensions
Width - 99.5cm
Depth - 39.5cm
Height - 71.5cm
Berkeley - 4+1 Sideboard
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 11/05/15
Important - Please read these instructions fully before starting assembly
417/8976
ALR3152
hygena

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 31kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
4
Left End (DF2882)
(563 x 392mm)
Top (DF2880)
(995 x 394mm)
Shelf (DF2886)
(447 x 373mm)
Right End (DF2883)
(563 x 392mm)
Divider (DF2884)
(563 x 392mm)
Base (DF2881)
(995 x 394mm)
Drawer Front (DF2885)
(495 x 137mm) x 4
Drawer Back (W447-95)
(447 x 95mm) x 4
Left Drawer Side (W350-95LH)
(350 x 95mm) x 4
Drawer Base (T458-347)
(458 x 347mm) x 4
Back (X987 x 589)
(987 x 589mm)
Right Drawer Side (W350-95RH)
(350 x 95mm) x 4
5
6
7 9
108
11
Door (DF2887)
(557 x 457mm)
12 13

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
M N
C
Metal dowel (F901) x 14
Wooden dowel (F22) x 12
Small locking
nut (F3) x 8 Large locking
nut (F900) x 6
40mm Screw (F910) x 6
RR Runner (F160) x 4
b
L Runner (F161) x 4
Rc
L Runner (F159) x 4
Ra
R Runner (F162) x 4
Rd
350mm long
J
13mm Screw (F52) x 24 13mm Screw (F63) x 28
Knock-in Peg (F171GY) x 16
K
Wedgefix (F639) x 8
13mm Screw (F79) x 16
L
S
OStrap
Screw Washer x 2
Overbalance protector kit (F269) x 1
P Q
Hinge (F518) x 2
Hinge plate
(F523) x 2
Nail (F51) x 22
T
Leg Bracket
(F333) x 4
Handle (F415WAL) x 1
Leg (F343) x 4
Shelf stud (F110) x 4
25mm Screw (F50) x 1

7
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 4
x 4 x 4
A
B
A
B
B
BB
910
Step 2
Prepare the 4 drawer
fronts
Screw 2 metal dowels
into each of the 4 drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
7
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
9
10
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
7
B
B
9
10
9
10
A
A
7

7
Assembly Instructions
5
Step 4
J
J
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
11
9 10
7
8
9 10
11
8
8
J
9 10
Step 6
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
K
J
J
K
K
K
11
9
8
9
10
11
10 x 4
x 4
x 4

Assembly Instructions
6
Step 7
Fit runners to the
drawers
Fit the runner to the
bottom edge of the left
drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the runner to the
bottom edge of the right
drawer side using the
same method.
10
R c
9
7
G
R d x 4
G
G
G
G
R c
R d
Runners must be
pushed up against
the drawer front
10
9
7
D
D
Prepare the right end
Tap 4 wooden dowels
into the right end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the right end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the
finished front edge.
C
C
P
P
P
C
2
P
2
D
D
D
2
2
Finished
front edge
Step 8
C
10mm
D

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 9
Step 10
C
A
Fit the right end to
the top
Push the right end
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right end .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
C
2
Prepare the top
Screw 6 metal dowels
into the top .
A
4
A
A
A
A
A
A
4
Finished
front edge
2
4

Assembly Instructions
Step 11
8
Finished front edge
Finished front edge D
D
Finished front edge
a:
Prepare the left end
a: Fit 4 runners to
the left end .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
c: Tap 4 wooden
dowels into the left
end .
Insert 2 large locking
nuts into the left end
. .
b:
D
C
1
1
R a
1
I
I
c:
R a
I
Finished front edge
I
1st
screw
2nd
screw
I
3rd
screw
R a
Finished front edge
G
G
R a
I
R a
I
I
I
R a
I
I
I
R a
I
I
I
R a
I
I
G
G
G
G
C
C
D
D
1
1
1

Assembly Instructions
9
Step 12
D
D
Finished
front edge
Fit the left end to the
top
Push the left end
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left end .
4
1
C
1
1
4
Step 13
a:
b:
Prepare the divider
a: Fit 4 runners to
the divider .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the 2nd hole in at the top
of the runner .
Tap 4 wooden dowels
into the divider .
Insert 2 large locking
nuts into the divider
. .
C
3
R b
3
I
I
G
R b
R b
I
Finished front edge
I1st
screw
2nd
screw
I3rd
screw
R b
Finished front edge
G
I
I
R b
I
I
I
R b
I
I
I
R b
I
I
I
R b
I
Finished
front edge
G
G
G
G
C
C
D
D
D
3
3
3