Igloohome RG1 Installation and maintenance instructions

1
Version 0.1 07/21
Installers &
User guide
Glass Door Lock.
RG1

As our igloohome app is frequently updated, there may be changes to this manual.
Please refer to our website igloohome.co/support for the latest version of the manual.
Welcome!
This guide will get you up and running with your igloohome Glass Door Lock.
In the meantime, you should follow igloohome on Facebook and Youtube!
Visit ourYoutubeLike us on Facebook

Table of Contents
What’s Included 4
Specifications 5
Installation Guide
Requirements 6
Prepare Lock for Installation 7
Installing/Replacing Batteries 9
Installation Instructions
Double Glass Doors 10
Single Glass Doors 13
User Guide
Lock Anatomy 16
Features 17
Unlocking from the Outside 19
Unlocking from the Inside 21
Locking from the Outside 23
Locking from the Inside 25
App Onboarding 26
Managing Access in App 27
Lock Behaviour 29
9V Jumpstart 31
Audio and LED Indications 32
Troubleshooting 33

4
What’s Included
Lock Assembly Clip-On Striker
AA Alkaline Batteries x4 RFID Tags x2
Drill Sheet RFID Stickers x2
Smart Module
Magnet Sensor

5
Specifications
Model
Battery Type
Battery Life
Emergency Power
RG1
4 x AA* Alkaline
Up to 10 months
9V Alkaline Battery
Operation Temp -20°C to 50°C
Battery Operation Temp -10°C to 50°C
IP Rating IP54
Material ABS, PC , Al, Zn
Weight Net: 1.3kg, Gross: 1.6kg
Unlock Mechanism Bluetooth, PIN code, RFID Tags/Stickers
Front BackSide
171mm
190mm
77mm47mm 20mm 47mm
22mm
66mm
43mm
171mm
* DO NOT USE: Heavy Duty, Eveready, GP, or rechargeable batteries. Please note that using recommended
battery brands such as Panasonic, Duracell, or Energizer will improve the performance and lifespan of the lock.
77mm 47mm
66mm
43mm

6
Measurements
Supported glass door thickness : 12mm
The Glass Door Lock is designed to fit 12mm swinging glass doors only. Do ensure that
there is sucient clearance on your glass door for lock unit and clip-on striker.
> 20mm
> 47mm
> 77mm
Door Thickness
Installation Guide
Requirements
a
c d
Clearance
a
c
d
b
> 190mm
b

7
Prepare Lock For Installation
Install Smart Module
1. Unfasten the screws of the indoor unit and remove the housing
2. Snap the Smart Module into position and connect the cable
3. Assemble back the housing and fasten with the screws.
Snap the
Smart Module
Connect
the Cable

8
Glass Door and Lock Assembly orientation
Left Hand Installation ‘LH’ Lock Assembly Orientation
Right Hand Installation ‘RH’ Lock Assembly Orientation
* Hinge is on your right.
Hinge
Outside
Clip-On
Striker
* Hinge is on your left.
Outside
Hinge
Clip-On
Striker
The keypad will be orientated automatically depending on how the lock is positioned during
installation.
Note: After a period of use, the keypad orientation will become fixed. To reset this, simply remove
and reinstall the batteries.

9
Installing/Replacing Batteries
Put back the battery cover and
tighten the screw.
Using your fingers, loosen the screw on the battery cover
and remove the battery cover.
Install or replace with 4 new
AA alkaline batteries
Twist to loosen screw
Battery Cover

10
Installation Instructions
Lock one side of the glass doors in place. This must remain
locked to use the lock.
Use a wet wipe/wet cloth to wipe the area of the glass door
where the glass door lock will be installed on.
Double Glass Doors
If this is not done, the lock
will not secure the glass
doors properly.