Igloohome Smart IoT Deadbolt Installation and maintenance instructions

1
Version 0.1 10/20
Installers &
User guide
Smart IoT
Deadbolt.

As our iglooworks app is frequently updated, there may be changes to this manual.
Please refer to our website igloohome.co/support for the latest version of the manual.
Welcome!
This guide will get you up and running with your igloohome Smart IoT
Deadbolt. In the meantime, you should follow igloohome on Facebook
and Youtube!
Visit ourYoutubeLike us on Facebook

Table of Contents
What’s Included 4
Specifications 5
Installation Guide
Requirements 6
Prepare Door for Installation 7
Prepare Lock for Installation 9
Installation Instructions 10
Test Lock 17
Prepare the Door Frame 18
User Guide
Lock Anatomy 19
Features 20
Unlocking and Locking 22
Lock Pairing & Provisioning 23
iglooworks App Functions 24
Lock Behaviour 25
9V Jumpstart Feature 26
Audio and LED Indications 27
Troubleshooting 28

4
What’s Included
Front Assembly
& Rubber Gasket
Back Assembly
Rubber Gasket
Back Assembly
AA Alkaline Batteries x8
Bolt Assembly
Construction Keys x4
Permanent Keys x4
Screw Holder
Back Plate
Strike Plate Housing &
Strike Plate
Door Sensor & Magnet
Drill Sheet
Edge of the door Face of the door
Fold this line
60mm (2-3/8”) backset
70mm (2-3/4”)backset
Centerline
10mm (Optional)
54mm
Door Thickness
Drill for:
Drill for:
35mm (1-3/8”)
Drill for:
45mm (1-3/4”)
Drill for:
60mm (2-3/8”)
Drill for:
70mm (2-3/4”)backset60mm (2-3/8”) backset
Drill for: Drill for:
Drill a 25mm (1”) hole at the center
of dooredge based onyour
DoorThickness measurements
25mm
Drill Sheet
Version0.2 03/18
22mm (0.87”)
Wood Screw x6
40mm (1.57”)
Bolt Screw x3
6mm (0.24”)
Bolt Screw x1
4mm (0.16”)
Bolt Screw x2
Keyhole
Cover x1
8mm (0.31”)
Bolt Screw x4

5
Specifications
Model igloohome Smart IoT Deadbolt
Battery Type 8 x AA* Alkaline
Battery Life Up to 1 Year
Emergency Power 9V Alkaline Battery
Operation Temp -25°C to 55°C
Storage Temp -40°C to 70°C
IP Rating IP65
Material AI, Zinc Alloy, ABS
Weight Net: 450g, Gross: g
Unlock Mechanism Bluetooth, PIN code, Physical Keys, Thumbturn
Front BackSide
145mm (5.70”)
60mm (2.36”) 11mm (0.43”) 58mm (2.28”) 76mm (2.99”)
185mm (7.28”)
* DO NOT USE: Heavy Duty, Eveready, GP, or rechargeable batteries. Please note that using recommended
battery brands such as Panasonic, Duracell, or Energizer will improve the performance and lifespan of the lock.

6
Installation Guide
145mm (5.70”)
185mm (7.28”)
Requirements
Measurements
45mm (1.77”) to 80mm (3.15”)
10mm (0.39”)
20mm (0.78”)
>110mm (4.33”) for 60mm (2.36”) / >120mm (4.72”) for 70mm (2.75”) backset
50mm (1.96”)
a
b
c
d
e
a
bb
b
c
e
d
Clearance
Door Thickness

7
Please ensure that there is an existing handle on your door for push - pull access.
Not for: metal gates, glass doors or sliding doors.
If you are unsure if your door is suitable, send us web links to your door pictures to inf[email protected]
Prepare Door for Installation
Items needed:
Recommended
Door and door frame material : Wood
Recommended
Gap between door and door frame: <3mm (0.01”)
DrillDrill Sheet 10mm (0.39”)
Drill Bit
54mm (2.12”)
Hole Saw
25mm (0.98”)
Spade Bit
#2 Phillips Screw Driver 20mm (0.78”)
Chisel
Hammer

8
How to use the Drill Sheet
Mark the center of the holes and then drill for accuracy.
Drilling (Door)
Make sure this is
aligned to the centre
of door edge
Door edge
Fold here
before drilling
holes for side
Chiselling
Put the bolt tongue in &
chisel around the edge
54mm (2.12”)
Hole Saw
10mm (0.39“)
Drill Bit
54mm (2.12”) 54mm (2.12”)
Deep
57mm
(2.25”)
25mm (0.98”)
25mm (0.98”)
Spade Bit
20mm
(0.78”)
Chisel
20mm (0.78”)
Chisel

9
Remove Battery Cover from the Back Assembly
Slide Up
Set Back Assembly for Left / Right Hand Installation
Set the toggle to ‘R’ for
right-hand installation
Right Hand Installation
Set the toggle to ‘L’ for
left-hand installation
* Hinge is on your left.
* Hinge is on your right.
Left Hand Installation
Hinge
Outside
Hinge
Prepare Lock For Installation

10
Installation Instructions
Measure
If you are replacing your current deadbolt lock, industry standards are 60mm (2.36”) or 70mm
(2.75”) backset. To determine which backset length you should use, so measure the distance (x)
between the center of 54mm (2.12”) hole to door edge.
Prepare bolt assembly based on the distance (x)
Bolt ships with bolt assembly in 60mm (2.36”) position. If required, twist the bolt and pull to extend
(Simultaneously) to 70mm (2.75”) backset position.
Twist upwards
Pull
Twist downwards
to lock backset position
XX
54mm
(2.12”)
Hole

11
Insert bolt and front assembly into door edge
The ‘+ ‘ hole on the backset should be in the middle of the hole.
Screw Holder
Screws
15mm (0.59”)
Measure and cut the tailpiece if necessary
After inserting the tailpiece, measure the distance of protrusion from the door.
If the door thickness is 70-80mm, you will not need to cut tailpiece during installation.
c
c
Please ensure that tailpiece
is in horizontal position of INB1
Door thickness (mm) No. of notch to cut
65 1
60 2
55 3
50 4
45 5
Notch The recommended tailpiece protrusion
from the door is 15mm (0.6”).

12
Screws
40mm (1.57”)
Door Sensor Installation
Adjust the position of the door sensor according to the door handling (left or right hand installation).
Use the 2 x 5mm (0.24”) screws to secure the door sensor to the back plate.
Screws
4mm (0.16”)
Right-hand Installation Left-hand Installation
e
d
e
e
Secure the Front Assembly using the Back Plate.
To do this, place the Back Plate (ensuring the correct side placement).
5
Do not overtighten the screws
Follow this orientation
d
d
d
e
e

13
Right-hand Installation Left-hand Installation
Fit in the Rubber Gasket
Insert the front assembly cable through the rectangular hole on the rubber gasket.
The hole should be on the right side of the rubber gasket.
Assembly Cable
Door Sensor Cable
goes through the
arched hole on the
Rubber Gasket
6

14
Connect Assembly Cable
Connect the sensor cable to the Back Assembly then connect the assembly cable from the
Front assembly through the 54mm (2.12”) hole to the Back Assembly. Ensure that the wire
is installed properly and securely.
Fit Back Assembly to the Door Tailpiece
Ensure thumbturn position is turned to ‘unlock’ position.
Thumbturn
is in vertical
position
Thumbturn is
in horizontal
position
Assembly
Cable
7
8
Right-hand Installation Left-hand Installation
Door Sensor
Cable

15
Secure the Back Assembly
Press and pull the ends
of the communications
module to release it
Do not overtighten the screws
Screws
8mm (0.31”)
9
10 Install SIM Card to the Communications Module
Remove the communications module from the top of the unit. On the bottom of the
communications module, you’ll see a SIM card sticker label and a SIM card slot.
Insert your SIM card into the SIM card slot following the SIM card sticker label direction.
Insert SIM card
according to the
Sticker Label direction
The SIM card has to be an IoT SIM card, please
reach out to your local internet service providers
for getting the IoT SIM cards.

16
Insert 8 AA Alkaline Batteries and slide the battery cover
downwards to close
Before inserting the batteries, please ensure the ribbon is spread
across the battery compartment for easier battery removal in the future.
It is optional to secure the battery cover further with the additional screw.
11
Screws
6mm (0.24”)
e
Top View of Battery Cover
Tighten the screw
from the top to further
secure the batter cover
Side View
Slide Down

17
Still experiencing issues?
Test Lock
Place hand over your lock to activate touchpad and hold ‘Unlock’ icon to lock.
Does your bolt lock?
Ye s No
Congrats!
Your lock is correctly installed.
Proceed to next steps.
Bummer!
Does the bolt lock and unlock
when you turn the thumbturn?
Ye s
Left-Right toggle
incorrectly set
No
Tailpiece and/or thumbturn
incorrectly set
Troubleshoot: Try Setting the
left-right toggle on your back
assembly to the correct side.
(See Pg. 10)
Troubleshoot: Dissemble lock
and install it again.
Go to igloohome.co/support for more help

18
Prepare the Door Frame
Ensure to align the lock to the door frame
and mark it down.
Same height
Door
Frame
Mark out where the bolt tongue locks then
drill a corresponding hole on door frame.
Chisel to fit the strike plate in as well.
Mark & Drill Hole
Secure strike plate housing and strike
plate using 2x 25mm (0.98”) wood screws.
Paste the magnet opposite the door
sensor.
1mm
(0.0039”)
25mm (0.98”)
Spade Bit
20mm (0.78”)
Chisel
26mm
(1.02”)
58mm
(2.28”)
4
Door Sensor
Magnet
Door
Sensor

19
Front & Back Assembly
Touch Screen
Keypad
Unlock
Key hole Cover
(Remove cover to
access physical
key unlock)
9V Jumpstart
Clear
Thumbturn
Downlight LED
LED Indicator
Battery Cover
User Guide
Lock Anatomy

20
Features
Auto Re-lock
EmergencyJump-Start
The igloohome Smart IoT Deadbolt
relocks automatically when door is
closed. User can configure the delay
or deactivate relock if they prefer to.
Do note that function will only work
when Sensor is installed.
If battery power is drained, an
external 9 Volt battery can be used
to provide emergency power. The 2
contact points of the battery must be
aligned with the 2 contact points on
the Smart IoT Deadbolt for 2 seconds.
Manual Locking
Hold the ‘Unlock’ button for 1 second
to manually lock the Smart IoT
Deadbolt. It also can be locked by
manually rotating the thumbturn from
the inner side of the door.
Lock
Battery
Bluetooth Key
The igloohome Smart IoT Deadbolt
unlocks with Bluetooth via the app.
Master PIN Code
The igloohome Smart IoT Deadbolt
unlocks with a permanent Master PIN
Code.
User PIN Code
The iglooworks management
dashboard can generate multiple
types of User Pin codes, e.g.
One-Time, Permanent & Duration.
PIN / Bluetooth Unlock