IHP H0776 User manual

1
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INSTALLATION INSTRUCTIONS FOR FIREBOX LINER KITS
FOR USE WITH FIREPLACE MODELS LISTED BELOW
SHIPPING AND PACKING LIST
Package 1 of 2 contains:
1 - Left Side Panel (Kits: H0775, H0776, H0777, H0779, H0781, H0912,
H2067, H2068, H2069, H2071, H2073, H3207, H4683, H4684,
H4685, H4686).
1 - Right Side Panel (Kits: H0775, H0776, H0777, H0778, H0779,
H0780, H0912, H2066, H2067, H2068, H2069, H2070, H2071,
H2072, H2073, H3207, H4683, H4684, H4685, H4686).
1 - Rear Panel (Kits: H0775, H0776, H0777, H0780, H0781, H0912,
H2067, H2068, H2069, H2071, H2073, H4683, H4684, H4685,
H4686).
1 - Baffle (Kits: H0775, H0776, H0777, H2067, H2069, H2071, H2073).
1 - Template (Kit: H0779)
1 - Installation Instructions.
Package 2 of 2 (for Kits H2023, H2024, H2074 & H2075 only) contains:
1 - Rear Log (H1381).
FIREBOX LINER KITS
750160M
Rev. N 03/2016
Figure 1 (40" Front Open)
Left Side
Firebox Wall
Front Lintel
Lintel Securing
Screw (Both Sides)
Rear Lintel
Right Side
Firebox Wall
Grate Assembly Log Spacer Ceramic Fiber Floor
(Some Older Models)
Clay Tan Interior Shown
(Some Older Models)
MODELS
This Firebox Liner Kit (see Figure 1)is for use only in the following
models of fireplaces:
Color: Boston Buff
Catalog # Model # Where Used *
H0775 EBLK-35 EDV3530
H0776 EBLK-40 Altair™ 40, DRT4040, EDV4035
H0777 EBLK-45 Altair 45, DRT4045, EDV4540
H0778 EBLK-PF Libra™40PF, DRT40PF,
MHD40PF, EDVPF, EBVPF
H0779 EBLK-ST Libra40ST, DRT40ST,
MHD40ST, Marin™ 40ST, BRT40ST,
EDVST, EBVST
H0780 EBLK-CL Libra 40CL, DRT40CL, EDVCL
H0781 EBLK-CR Libra40CR, DRT40CR, EDVCR
H0912 MBLK-33T MPDT3328/MDT3328/DT400
H8596 BLKC-MP40 D600/DR600
H8614 BLKC-MP33R MPDR3328/MDR3328/DR400
H2023 MBLK-40L MPD4035
H2024 MBLK-45L MPD4540
H3207 MBL-35ST Eros™ 35ST/PF, DRT35ST/PF,
Rochester™ ST/PF, MPB35ST,
MPD35ST
H4683 MBLK-33B MPB-33
H4684 MBLK-35B MPB-35
H4685 MBLK-40B MPB-40
H4686 MBLK-45B MPB-45
Color: Black
Catalog # Model # Where Used
H2067 BBLK-4R(R) DR-400, MDR3328
H2068 BBLK-5T(R) DT-500
H2069 BBLK-5R(R) D500, DR500, MPD3530-B, BDM35
H2071 BBLK-6R(R) D600/DR600
H2073 BBLK-8R(R) D800/DR800
H2086 BBLK-45(R) MPD4540-B
* The accessories listed here will fit Lennox Hearth Products (LHP) fire-
place models that are shown above in a smaller font.
HEARTH PRODUCTS
KITS AND ACCESSORIES
fire-parts.com

2
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 4 (40" Front Open)
Baffle
Figure 3 (40" Front Open)
Left Side Panel Right Side Panel
Front Lintel Screws (5 Places)
INSTALLATION INSTRUCTIONS -
LHP FIREPLACE MODELS - MPD, MPB & SUPERIOR D-SERIES
(For Kits: H0912, H2023, H2024, H2067, H2068, H2069, H2071,
H2073, H2074, H2075, H4683, H4684, H4685 & H4686)
Step 1. Follow the procedure "Turning Off Gas To Unit", located on the
Lighting Instructions pullout labels in the control compartment of the
unit and in the Installation Instructions provided with the appliance.
Step 2. Refer to the appliance Installation and Operation Instructions
and gain access to and remove the front glass enclosure panel.
Step 3. Carefully remove the log set from the firebox.
Step 4. Remove the existing rear lintel (if applicable) as shown in
Figure 1 by removing the two screws. Use the screws to plug the two
screw holes.
Figure 2 (40" Front Open)
Rear Panel
INSTALLATION INSTRUCTIONS - FRONT OPEN FIREPLACES
(For Kits: H0775, H0776 & H0777)
Step 1. Follow the procedure "Turning Off Gas To Unit", located on the
Lighting Instructions pullout labels in the control compartment of the
unit and in the Installation Instructions provided with the appliance.
Step 2. Refer to the appliance Installation and Operation Instructions
and gain access to and remove the front glass enclosure panel.
Step 3. Carefully remove the log set from the firebox.
Step 4. Remove the existing rear lintel as shown in Figure 1 by removing
the two screws. Use the screws to plug the two screw holes.
Step 5. Remove and discard the log spacer as shown in Figure 1 by
removing the two screws.
Step 6. Insert the rear panel into firebox and position against the rear
wall of the firebox (see Figure 2).
Step 7. Carefully slide the left side panel into firebox between the left
side firebox wall and the front lintel (see Figure 3).
NOTE: For some older models, the front lintel needs to be removed by
unscrewing the five (5) attaching screws, and requires the field trim-
ming of 3/4" on each end, in order for the panels to fit. After trimming,
reinstall the front lintel using the five (5) existing screws.
NOTE: Previous EDV models with clay-tan painted interiors were shipped
from the factory with ceramic fiber brick pattern floor finish treatments.
These floor panels will raise the side panels of the newest brickaded
panel liner kits, causing a misalignment of the brick pattern relation to
the rear panel. To correct, either remove the floor panels and replace
with decorative volcanic stone to taste (Model FDVS - 80L42) or using
a box knife, cut 1/2" off the bottom edge of each side panel.
Step 8. Repeat Step 7 for the right side panel.
Step 9. Place the ceramic baffle into the firebox as shown in Figure 4.
Step 10. Carefully replace the log set. Refer to the Installation and
Operation Instructions and the detailed Log Set Placement Supplement,
included with the appliance.
fire-parts.com

3
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 5 (PF Models)
Figure 6
Cut-Out In Panel For Rear Vent Access
Right Side Panel
(Top Vented Shown)
Front Lintel Screws (5 Places)
Ceramic Fiber Floor (Some Older Models)
Step 4. EBLK-ST (Catalog # H0779)
A. For Top Vented application.
1. Slide the provided left and right side panels into the unit as
shown in Figure 9.
NOTE: For some older models, the front two (2) lintels need to be re-
moved by unscrewing the four (4) attaching screws on each lintel, and
requires the field trimming of 3/4" on the panel end of the lintel, in order
for the panels to fit. After trimming, reinstall the front lintels using the
four (4) existing screws.
Step 2. Refer to the appliance Care & Operations/Installation Instruc-
tions and gain access to and remove the front glass enclosure panel.
Step 3. EBLK-PF (Catalog # H0778)
A. For Top Vented application.
1. Slide the provided side panel into the unit as shown
in Figure 5.
NOTE: For some older models, the front two (2) lintels need to be re-
moved by unscrewing the five (5) attaching screws on each lintel, and
requires the field trimming of 3/4" on the panel end of the lintel, in order
for the panels to fit. After trimming, reinstall the front lintels using the
five (5) existing screws.
B. For Rear Vented application.
1. To allow for rear vent access, remove the U-Shaped cut-out
from the back of the provided panel. Using a standard utility
knife, cut through panel material along the U-shaped line
and then discard the cut out piece. See Figure 6.
2. Slide the panel into the unit as shown in Figure 5. (See Note
Above).
Step 5. Insert the rear panel into firebox and position against the rear
wall of the firebox (refer to Figure 2).
NOTE: (for Kits H0915, H2024 & H2075 only): Use a utility knife or
blade to remove excess material, using perforated line on the back of
the panel as a guide.
Step 6. Carefully slide the left side panel into firebox between the left
side firebox wall and the front lintel (refer to Figure 3).
NOTE: For some older models, the front lintel needs to be removed by
unscrewing the attaching screws, and requires the field trimming of 1/2"
on each end, in order for the panels to fit. After trimming, reinstall the
front lintel using the existing screws.
Step 6a. (For Kits: H2067, H2069, H2071, H2073, H2074 & H2075)
Install provided lintel using the existing screws.
Step 7. Repeat Step 6 for the right side panel.
Step 8. Place the ceramic baffle into the firebox (if applicable) as shown
in Figure 4.
Step 9. (For Kits: H2023, H2024, H2074 & H2075 only) Replace the
rear log (39-7 molded on back) with the log provided (138 molded on
back). Please save the original log for future burning without ceramic
panel (if desired).
Step 10. Carefully replace the log set. Refer to the Installation and
Operation Instructions and the detailed Log Set Placement Supplement,
included with the appliance.
INSTALLATION INSTRUCTIONS - MULTI OPEN FIREPLACES
(For Kits: H0778, H0779, H0780, H0781 & H3207)
Step 1. Follow the procedure "Turning Off Gas To Unit", located on the
Lighting Instructions pullout labels in the control compartment of the
unit and in the Installation Instructions provided with the appliance.
fire-parts.com

4
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 9
Step 5. EBLK-CL (Catalog # H0780), EBLK-CR (Catalog # H0781)
A. For Top Vented application.
1. Slide the provided rear panel into the unit as shown in
Figure 10.
NOTE: For some older models, the side and front lintels need to be
removed by unscrewing the two (2) and five (5) attaching screws
respectively, and requires the field trimming of 3/4" on the panel end
of the lintels, in order for the panels to fit. After trimming, reinstall
the side and front lintels using the existing screws.
2. Slide the provided side panel into the unit as shown in
Figure 11. (See Note Above).
Figure 7 - B-Vent ST Models
Figure 8 - B-Vent ST Models
Right Side Panel
(Top Vented Shown)
Left Side
Panel
Front Lintel Screws
(4 Places)
C. For Rear Vented application.
1. To allow for rear vent access, remove the U-Shaped cut-out
from the back of one of the provided panels. Using a standard
utility knife, cut through panel material along the U-shaped line
and discard the cut out piece. Refer to Figure 6. (See Note
at the bottom of Page 3).
2. Slide the panel with the U-shaped cut out removed into the
unit (on the vented side of the unit) as shown in Figure 9.
3. Slide the other provided panel into the unit, as shown in
Figure 9. (See Note at the bottom of Page 3).
Template
Cut along
dashed lined
B. For "B" Vent application.
1. To allow for relief opening access, place template on back side of
panel (see Figure 7)using a standard utility knife, cut through panel
material along the U-shaped line and discard the cut out piece (see
Figure 8).
2. Remove the two (2) front lintels by unscrewing the four (4) at-
taching screws on each lintel.
3. Slide the panel with the U-shaped cut-out removed into the unit
(on the relief opening of the unit) as shown in Figure 9.
4. Slide the other provided panel into the unit as shown in Figure 9.
5. Reinstall the front lintels using the existing screws.
fire-parts.com

5
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 10 (CR/CL Models)
Side Panel (Top Vented Shown) Rear Panel
Figure 11 (CR/CL Models)
Rear Panel
Front Lintel Screws
(5 Places)
Side Lintel Screws
(2 Places)
B. For Rear Vented application.
1. Slide the provided rear panel into the unit as shown in
Figure 10. (See Note Above).
2. To allow for rear vent access, remove the U-Shaped cut-out
from the back of one of the provided panels. Using a standard
utility knife, cut through panel material along the U-shaped line
and discard the cut out piece. Refer to Figure 6.
NOTE: Make sure to remove the appropriate cut out corresponding to
your unit model number, CL (corner left), CR (corner right).
3. Slide the side panel with the U-shaped cut out removed into
the unit (on the vented side of the unit).
NOTE: For some older models, the side and front lintels need to be
removed by unscrewing the two (2) and five (5) attaching screws
respectively, and requires the field trimming of 3/4" on the panel end
of the lintels, in order for the panels to fit. After trimming, reinstall
the side and front lintels using the existing screws.
fire-parts.com

6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Printed in U.S.A. © 2003 Innovative Hearth Products
P/N 750160M Rev. N 03/2016
IHP reserves the right to make changes at any time, without notice, in design, materials,
specifications, and prices, and also to discontinue colors, styles, and products. Consult your
local distributor for fireplace code information.
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
fire-parts.com