Inepro PayCon Touch - First Time Log On User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | PayCon Touch - First Time Log
On
PayCon Touch - First
Time Log On

PayCon Touch - First Time Log On
Congratulations on your selection of the Inepro . We are certain you will be pleased
with your purchase of one of the flexibele solutions of the market.
We want to help you get the best result from your . This manual contains information
on how to do that; please read it carefully. Due to continuous product improvements
this manual is subject to changes without notice.
We strongly recommend you read the license agreement to fully understand its
coverage and your responsibilities of ownership.
Your Inepro dealer is dedicated to your satisfaction and will be pleased to answer your
questions and your concerns.
Best wishes,
Inepro BV.
The most versatile payment solution

All rights reserved. No parts of this work may be reproduced in any form or by any means -
graphic, electronic, or mechanical, including photocopying, recording, taping, or information
storage and retrieval systems - without the written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered
trademarks of the respective owners. The publisher and the author make no claim to these
trademarks.
While every precaution has been taken in the preparation of this document, the publisher and
the author assume no responsibility for errors or omissions, or for damages resulting from the
use of information contained in this document or from the use of programs and source code
that may accompany it. In no event shall the publisher and the author be liable for any loss of
profit or any other commercial damage caused or alleged to have been caused directly or
indirectly by this document.
Created: May 2019 in Nieuw-Vennep.
Publisher
Managing Editor
Technical Editors
Cover Design
Inepro B.V.
K. de Graaf
P. Grimmerink
K. de Graaf
Production
Inepro B.V.
Team Coordinator
R. Groen
H. Wagenaar
PayCon Touch - First Time Log On
J. van den Berg
PayCon Touch - First Time Log On
P. Blom

http://www.inepro.com
Table of Contents
Introduction 1
Setup 3

ATTENTION!!
Read this manual carefully before installing the P ay C on Touch!
Mains connection
Guar entee
Security
Before connecting the appliance to the mains, check that the mains supply v oltage corresponds
to the v oltage printed on the ty pe plate of the adapter. If the mains v oltage is different, consult
y our supplier.
No guarantee can be giv en if safety regulations are not follow ed.
A lw ay s disconnect the pow er supply before handling any thing inside the dev ice.
This dev ice is in conformity w ith the EM C directiv e and low -v oltage directiv e.
CE Confor mité Eur opeène (Conform Eur opean Nor m)
End of life dir ectives
Inepro is pay ing a lot of attention to env ironmentally -friendly production. Your new dev ice contain
materials w hich can be recy cled and reused. A t the end of its life specialised companies can
dismantle the discarded dev ice to recy cle the reusable materials and to minimise the amount of
materials to be disposed of. P lease observ e the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.
This dev ice may only be used indoors.
Indoor User O nly
Directives

I
Introduction
Part

2 - PayCon Touch - First Time Log On
Introduction
PayCon Touch LED indicator
De LED on the PayCon touch can have 3 colours and
indicates the status of the PayCon Touch.
PayCon Touch
Colour
Status
Blue
Busy / Connecting...
Green
Standby
Red
No Connection / Error

II
Setup
Part

4 - PayCon Touch - First Time Log On
Setup
Configure PayCon Touch terminals
When the PayCon Touch starts when it hasn't been configured, you
will be able to set these connection settings. To do this press the
touchscreen at the lower right corner.
The setup menu will be available when; the settings have not yet
been set, when the network cable is not connected, or when the
Business Server is offline.
In the setup menu, carry out the following:
Fill out the Location ID and the Server address.

Setup
5
Enable or disable the DHCP.
Fill out the IP and Netmask.
Fill out the DNS and Gateway.